images
Computer Modeling in Engineering & Sciences
images

DOI: 10.32604/cmes.2023.027427

ARTICLE

Performance Analysis of Intelligent Reflecting Surface Assisted Wireless Communication System

Weiqiang Tan1,*, Quanquan Zhou1, Weijie Tan2, Longcheng Yang3 and Chunguo Li4

1School of Computer Science and Cyber Engineering, Guangzhou University, Guangzhou, 510006, China
2Key Laboratory of Advanced Manufacturing Technology, Ministry of Education, Guizhou University, Guiyang, 550025, China
3Sichuan Key Laboratory of Indoor Space Layout Optimization and Security Guarantee, Chengdu Normal University, Chengdu, 611130, China
4School of Information Science and Engineering, Southeast University, Nanjing, 210096, China
*Corresponding Author: Weiqiang Tan. Email: wqtan@gzhu.edu.cn
Received: 28 October 2022; Accepted: 13 December 2022

Abstract: In this paper, we investigate the end-to-end performance of intelligent reflecting surface (IRS)-assisted wireless communication systems. We consider a system in which an IRS is deployed on a uniform planar array (UPA) configuration, including a large number of reflecting elements, where the transmitters and receivers are only equipped with a single antenna. Our objective is to analytically obtain the achievable ergodic rate, outage probability, and bit error rate (BER) of the system. Furthermore, to maximize the system’s signal-to-noise ratio (SNR), we design the phase shift of each reflecting element and derive the optimal reflection phase of the IRS based on the channel state information (CSI). We also derive the exact expression of the SNR probability density function (p.d.f.) and show that it follows a non-central Chi-square distribution. Using the p.d.f., we then derive the theoretical results of the achievable rate, outage probability, and BER. The accuracy of the obtained theoretical results is also verified through numerical simulation. It was shown that the achievable rate, outage probability, and BER could be improved by increasing the number of reflecting elements and choosing an appropriate SNR regime. Furthermore, we also find that the IRS-assisted communication system achieves better performance than the existing end-to-end wireless communication.

Keywords: Massive MIMO; intelligent reflecting surface; uniform planar array; achievable ergodic rate

1  Introduction

With the evolution of modern communication systems, the beyond fifth-generation (B5G) and forthcoming sixth-generation (6G) are expected to provide ultrahigh throughput, massive connectivity, intelligent features, and high resource utilization [1–3]. The intelligent reflecting surface (IRS) is considered an emerging enabling technology for future wireless communications [4–6]. IRS is a low-cost planar array consisting of a large number of passive reflecting elements, which enables reconfiguration of the wireless propagation environment through a programmable controller. Furthermore, compared to conventional wireless communications systems, the IRS-assisted system can attain higher ergodic capacity, better outage probability, and lower BER [7,8].

The existing research on IRS-assisted MIMO communication systems is focused on system performance analysis, design optimization algorithms, and system architecture configuration. For system performance analysis, Han et al. [9] deduced the closed-form upper bound expression for the ergodic capacity of IRS-assisted communications in the Rice fading channel. For Rayleigh fading channels, Xu et al. [10] also showed that the received signal power could be approximated as the sum of two Gammas and two non-central Chi-squares and considered IRS-assisted communication system performance. With the results in [10], an analytical expression of the spectrum of wireless communication systems assisted by multiple IRS was obtained in [11], where the channel elements were assumed to follow a Gamma distribution. The research results showed that the IRS-assisted MIMO communication system could significantly improve system performance. The work in [12] studied the IRS-assisted communication channel model and showed that the equivalent channel of the IRS-assisted system follows the F distribution. The above research works are mainly based on statistical fading channel models such as Gaussian, Gamma, Rayleigh, or Rice random distributions. Nevertheless, experimental results show that the actual channels do not necessarily follow the assumption of independent and identical distribution. The channel behavior is also significantly affected by the carrier frequency and the configuration of the antenna array at the base station (BS) and the IRS. This is because the energy of wireless signals is often concentrated in a limited space, resulting in the existence of near- and far-field signals. The authors in [13] also investigated the secrecy performance of the simultaneously transmitting and reflecting reconfigurable intelligent surface under the Nakagami-m fading channels. They then derived analytical expressions for the secrecy outage probability (SOP) and showed that the system secrecy performance can be improved by increasing the number of configurable elements. In practice, an accurate channel model is a necessary condition for accurate analysis of the channel capacity. Furthermore, one needs to verify if the original research methods and the experimental conclusions are consistent. Therefore, it is an immediate need to establish an accurate channel model to characterize the performance limits of IRS-assisted mmWave MIMO systems.

In terms of designing optimization algorithms, the researchers designed active beamforming techniques at the BS and/or passive beamforming at the IRS. They then constructed an objective function to maximize performance indicators such as energy efficiency, spectral efficiency, latency, outage probability, bit error rate (BER), or computational complexity. In [14], the authors proposed an algorithm based on alternating optimization to design the optimal passive IRS beamforming to maximize energy efficiency. To reduce the computational complexity, Wu et al. [15] adopted the branch-and-bound method along with an exhaustive search method. They also proposed a unit-by-unit optimization algorithm to obtain passive beamforming assuming discrete reflection phase shifts. In [16], the authors also utilized the fixed-point iterative method and the manifold optimization algorithm to design the optimal passive beamforming and maximize system spectral efficiency. The computational complexity of the proposed method in [16] is however high due to multiple iterations. In [17], the authors converted the system spectral efficiency maximization problem into an SINR maximization problem and used the alternating direction multiplier method to derive the optimal IRS beamforming. By applying the power allocation scheme, Huang et al. [18] adopted the gradient descent algorithm and designed the optimal IRS beamforming to maximize energy efficiency. Furthermore, You et al. [19] proposed a channel estimation algorithm by controlling the overhead of IRS and joint optimization of the reflection phase shift. They then designed the transceiver that greatly improves the energy efficiency of the system. In the above research work, the authors utilized an ideal constant modulus phase based on the IRS reflection unit, where the base stations are assumed to have access to the perfect CSI. However, in the actual design, the IRS reflection unit has a discrete phase and it is difficult for the base station to obtain the perfect CSI. Therefore, the channel estimation and beamforming of mmWave massive MIMO systems in the case of inaccurate CSI and IRS discrete phases need to be investigated. In terms of system architecture configuration, Wang et al. [20] analyzed the IRS-assisted millimeter-wave massive MIMO system by joint optimization of the quantization phase shift for the analog and digital coding matrices assuming using IRS at the base stations. For this system, they then minimized the mean square error between the received symbols and the transmitted symbols. In [21], the authors studied the hybrid precoding design of multi-user IRS-assisted mmWave MIMO systems and performed MSE minimization by using the gradient projection method. Nevertheless, these works assume an all-digital high-precision analog-to-digital converter (ADC) architecture. In practice, however, the core high-precision ADC devices are not only expensive but also often consume lots of energy, especially for large bandwidths.

In this paper, we investigate the end-to-end performance of an IRS-assisted wireless communication system. In the considered system, the IRS is deployed to a uniform planar array (UPA) configuration with a large number of reflecting elements, and the transmitters and receivers are equipped with a single antenna. Our objective is to calculate the analytical expression of the achievable ergodic rate, outage probability, and BER of the system. To maximize the system’s SNR, we also design the phase shift of each reflecting element and derive the optimal reflection phase of the IRS in terms of the channel state information (CSI). We further derive the exact expression of the probability density function (p.d.f.) of the SNR, which follows non-central Chi-square distribution. Using p.d.f., we then derive the achievable rate, outage probability, and BER, and further verify their accuracy through numerical simulation.

Regarding the notation, bold upper and lower case letters such as A and a denote matrices and vectors, respectively. The vector or matrix transpose and conjugate transpose are represented by AT and AH, and get the real and imaginary parts from the corresponding vector or matrix, respectively. Additionally, diag [A] is a diagonal matrix only containing the diagonal elements of A. The inverse of the sine function is denoted by A−1. The expectation operator is denoted as E{⋅}. The Kronecker product is denoted by A⊗B.

2  System Model

We consider a single-cell centralized IRS-assisted wireless communication system, where there is no direct communication between the base station and the user. The IRS is utilized to assist wireless communication between the BS and users as shown in Fig. 1. In particular, the IRS is mounted on the walls of the surrounding tall buildings. We also assume that there is a single-antenna base station that transmits signals and serves single-antenna users. The IRS consists of N reflecting elements and the reflecting elements are arranged within a rectangle. In practice, the IRS can be installed on the walls of buildings or roadside structures to help with signal transmission. Supposing that the transmitting signal is a Gaussian signal, the received signal assuming a high-precision ADC is

y=phΘgx+n,(1)

where h∈C1×N denotes the vector of channel gains between the user and the IRS, g∈CN×1 denotes the vector of channel gains between the base station and the IRS, x is represents the input signal using M-ary phase shift keying (MPSK) modulation, and n is a white Gaussian noise n∼𝒞𝒩(0,N0), and Θ denotes the phase shift matrix of the IRS, which is represented by

Θ=diag⁡[ejθ1,ejθ2,…ejθN].(2)

Figure 1: A point-point wireless communication system with IRS configuration

In the above, θn denotes the phase shift of the n-th element of the IRS. It is usually assumed that the phase shift of the ideal reflection unit can be adjusted continuously. In practice, however, the phase shift of the reflection unit can only take discrete values within the [0,2π) interval.

In this paper, we assume ideal IRS reflection elements without power loss. A cascade channel consists of two channels from the BS to the IRS and from between the IRS and the user. The wireless channel also follows the Rayleigh fading where gi,hi∼𝒞𝒩(0,1). The channel vectors between the BS and the IRS and between the IRS and the user are therefore [22]

g=[g1,…gn…gN]T,(3)

and

h=[h1,…hn…hN],(4)

where gi=βie−jφi, hi=αie−jϕi, φ,and ϕ represents the angle of arrival (AoA) of the signal to the smart reflector and the angle of departure (AoD) from the base station to the smart reflector and from the smart reflector to the user, respectively.

In communication systems, analytical results can effectively characterize the system performance and the physical parameters can explore the performance trend and system parameters, e.g., the number of IRS elements, the number of transmit antennas at the base station, the number of users, and the transmit power of the base station. These parameters can accurately characterize the system’s achievable theoretical performance limits. Besides, we can utilize the derived analytical results as the benchmark and further optimize the physical parameters to boost the system performance under certain requirements. In the following section, we investigate the end-to-end performance of IRS-assisted wireless communication systems, where the IRS is deployed to a UPA configuration with a large number of reflecting elements.

3  Performance Analysis

In this section, we derive a closed-form expression for the p.d.f. of SNR. Using the p.d.f. of the SNR we then analytically obtain the effective rate, outage probability, and BER.

3.1 SNR Analysis

The IRS results in the co-existence of direct and indirect links. Here, however, we ignore the direct path and only consider the reflected path as in the slowly varying and flat fading channels. The received baseband signal reflected via the IRS with N passive elements is

y=p ∑i=1Nαiβiej(θi−ϕi−ψi)x+n.(5)

Using (1), the instantaneous SNR at the user end is expressed as

γ=p|hΘg|2N0=p|∑i=1Nαiβiej(θi−ϕi−ψi)|2N0,(6)

where p is the average transmitted energy per symbol and N0 is the variance of the noise n.

To order to analyze the performance of the system, it is necessary to obtain the p.d.f. of SNR in (6). The problem formulation is as the following:

P1:maxθiγ=p|∑i=1Nαiβiej(θi−ϕi−φi)|2N0, s.t. θi∈[0,2π),∀i,(7)

where N0 denotes the noise power that is a fixed value. To maximize γ, it is necessary to obtain the optimal IRS reflection phase θi for each, to maximize the received signal power p|∑i=1Nαiβiej(θi−ϕi−φi)|2. The SNR of the received signal is then maximized within a limited range. Note that we also need to obtain θi=ϕi+φi such that γ is maximized. The corresponding SNR is

γ=p|hΘg|2N0=p|∑i=1Nαiβi|2N0=pXN0.(8)

For the sake of brevity, let X=|∑i=1Nαiβi|2, where αi and βi are independent Rayleigh distributed random variables and E[αiβi]=π4 VAR[αiβi]=1−π216 [23]. Noting the definition of the non-central Chi-squared distribution [24], the p.d.f. is then written as

fY(y|σ,λ)=12σ2(yλ2)(n−2)/4e−(y+λ2)2σ2In/2−1(yλσ2).(9)

where λ and σ2 represent the mean and variance of Y, respectively, n denotes the number of Gaussian random variables, and Iv(⋅) is the modified Bessel function of the first kind, which is written as

Iv(y)=∑k=0∞(y2)v+2kk!Γ(v+k+1),(10)

In the above, Γ(⋅) is the Gamma function. We note that |α1β1|,|α2β2|,⋯,|αNβN| are independent random variables with means π4 and variances 1−π216. Therefore for N≫1, we can write

|∑i=1Nαiβi|2∼(Nπ4,N(16−π2)16).(11)

Considering the definition of the non-central Chi-squared distribution, it is easy to show that the random variable X follows a non-central Chi-square distribution with the degrees of freedom n=1, the mean of the non-centrality parameter λ=(Nπ4), and the variance of the non-centrality parameter σ2=N(16−π2)16. The p.d.f of the random variables X is then expressed as

fX(x)=4πN(16−π2)e−Nπ22(16−π2)(1x)14e−8xN(16−π2)In/2−1(x4π(16−π2)).(12)

For brevity, the p.d.f. of X is simplified as the following:

fX(x)=a(1x)1/4e−bxIn/2−1(cx),(13)

where a=4πN(16−π2)eNπ22(16−π2), b=8N(16−π2), c=4π(16−π2). A simple transformation of random variables shows that the series representation of Bessel functions I−1/2(⋅) can be given by

I−1/2(x)=12πe−x+exx.(14)

Therefore, the p.d.f of X can be further simplified to

fX(x)=a2cπ(1x)1/2e−bx(e−cx+ecx).(15)

In the following three sections, we will use the derived p.d.f. in (15) to analyze the key performance of the communication system including the achievable ergodic rate, outage probability, and symbol error rate.

3.2 Achievable Ergodic Rate Analysis

The achievable rate is an important service quality indicator in communication systems which represents the maximum theoretical achievable rate at the receiver. The achievable rate of the system using IRS assistance can be calculated from Shannon’s formula as

R=E{log2⁡(1+pX)},(16)

Using the p.d.f. of X, the system’s ergodic rate can be calculated as

R=∫0∞log2⁡(1+pxfX(x))dx.(17)

As can be seen in (17), the exact derivation over the range of SNR regimes is mathematically intractable and the expectation operation needs to be calculated through all vector realizations of the random variables X involving the modified Bessel function of the first kind. Therefore, it is difficult to directly derive an exact expression of the achievable rate. Alternatively, we attempt to infer a tractable upper bound on the achievable rate using Jensen’s inequality. This enables us to draw engineering insights into the system’s performance. Here we note that for X>0, E{log2⁡(1+X)} is a concave function [25]. Therefore, noting E{log2⁡(1+X)}<log2⁡(1+E{X}), we obtain the following upper bound for the achievable rate:

R<Ru=log2⁡(1+pE{X})=log2⁡(1+p∫0∞xfX(x)dx).(18)

By employing the derived p.d.f of X and substituting the (15) into (18), we have

Ru=log2⁡(1+pa2cπ∫0∞x(1x)12e−bx(e−cx+ecx)dx)=log2⁡(1+2pa2cπec24b(∫0∞x2e−b(x+c2b)2dx+∫0∞x2e−b(x−c2b)2dx))=log2⁡(1+pa2cπec24b1bb(π+cbe−c24b+c2π2b)),(19)

where a, b, and c were defined in (13). Therefore, we have derived an upper bound to the ergodic rate and observed that the analytical result is the function of the SNR regime and the number of reflecting elements. This reveals the tendency of physical parameters to change with the performance of the system.

3.3 Outage Probability Analysis

The outage probability is defined as the point that a given ergodic rate is not supported if the receiver power value falls below a threshold SNR. The outage probability is defined as

Pout=p(γ<γ0).(20)

In wireless communications, the outage probability is an important quality of service indicator. If the communication quality drops to a certain level, communication interruption occurs. This is defined as the probability that the received SNR drops below the acceptable minimum threshold. To provide insight into the system performance, the diversity order is often used to evaluate the outage behaviors for communication systems. This measure describes how quickly the outage probability decreases with the increase of the received power. By applying the definition of outage probability in (15), we write

Pout=∫0γ0pfX(x)dx,(21)

where γ0 represents the minimum acceptable SNR. Substituting (15) into (21) yields

Pout=∫0γ0pfX(x)dx=p∫0γ0a2cπ(1x)12e−bx(e−cx+ecx)dx=p2[erf(b(γ0+πN4))+erf(b(γ0−πN4))],(22)

where erf(⋅) represents the error function [26] erf(x)=2π∫0xe−t2dt. It is seen that the outage probability is a function of the SNR regime, the number of reflecting elements. The threshold SNR also significantly affects the outage probability.

3.4 Symbol Error Rate Analysis

The symbol error rate is an indicator measuring the accuracy of data transmission within a specified time. It is often defined as the frequency of bit errors in the transmission process. The research on BER is of great significance to enhance the performance of wireless communication systems and to improve the quality of data transmission. The formula for calculating the BER is as follows:

SER(p)=∫0∞σ1Q(2σ2px)pfX(x)dx,(23)

where σ1 and σ2 denote the modulation parameters and different values represent different modulation modes, Q(⋅) represents the right-tailed function Q(x)=12erfc(x2) of the standard normal distribution [27], and erfc(x)=2π∫x∞e−t2dt is the complementary error function [28]. Inserting (12) into (5), we have

SER(γ¯)=pσ12a2cπ∫0∞erfc(σ2γ¯x)(1x)1/2×e−bx(e−cx+ecx)dx=paσ12cπ∫0∞(1−erf(σ2γ¯x))×e−bx2(e−cx+ecx)dx=paσ12cπ(∫0∞e−bx2(e−cx+ecx)dx−∫0∞erf(σ2γ¯x)e−bx2(e−cx+ecx)dx).(24)

From (24), one can see that it is hard to obtain the closed-form expression of the SER. Alternatively, this result can be evaluated numerically by using standard software packages such as Matlab or Mathematica.

4  Simulation Results

In this section, we simulate and compare the performance of the system from different perspectives described in the previous section. We assume that the BS has a single antenna, the IRS is a UPA composed of N passive reflecting elements, and g and h follow Rayleigh distribution. In our simulations, different parameters, such as SNR and the number of IRS elements are set separately.

Fig. 2 depicts the total achievable ergodic rate vs. SNR for different numbers of reflecting elements, including the theoretical analysis result, the upper bound, and the Monte Carlo simulation provided in (17), and (19), respectively. It is seen that the total achievable ergodic rate is significantly improved by increasing SNR. It is also seen that the analytical results are in good agreement with the Monte Carlo simulations validating the correctness of the upper bound obtained in (19). Moreover, the ergodic rate is significantly increased by increasing the number of emitted elements which indicates that the high SNR regimes can bring significant performance gains. For comparison, we also present the total rate of the system with different numbers of reflecting elements. It is seen that using a large number of reflecting elements leads to significant performance gains.

Figure 2: Total achievable ergodic rate vs. SNR for different numbers of reflecting elements

Fig. 2 depicts the total achievable ergodic rate vs. SNR for the different numbers of reflecting elements, which includes the theoretical analysis result, the upper bound, and the Monte Carlo simulation provided in (17), and (19), respectively. It can be seen intuitively that the total achievable ergodic rate improves significantly with the increase of SNR. Besides, we also see that the analysis results are in good agreement with the Monte Carlo simulation results, which validates the correctness of the upper bound of (19). Moreover, the ergodic rate increases significantly with the number of emitted elements which indicates that the high SNR regimes can bring significant performance gains. For comparison, we also depict the total rate of the system with different numbers of reflecting elements, showing that using a large number of reflecting elements can lead to significant performance gains.

Fig. 3 shows the total achievable ergodic rate vs. the number of reflecting elements. It is seen that the ergodic capacity significantly increases with the increasing numbers of reflecting elements. This indicates that the use of a large number of reflecting elements can lead to significant performance gains. Of course, when the number of reflected elements is small, there is a certain gap, but when the number of reflecting elements is about 30, the gap almost disappears. This further indicates that the use of a large number of reflecting elements brings significant performance gain.

Figure 3: Total achievable ergodic rate vs. the number of reflecting elements

Fig. 4 shows the outage probability of the system vs. the number of reflecting elements. In the simulation, the minimum acceptable SNR and the average transmitted power p are both set to 1 dB. It is seen that the outage probability decreases by increasing the number of emitted elements demonstrating a linear relationship. This implies that for a fixed transmit power, the outage probability can be improved by including a larger number of reflecting elements.

Figure 4: The outage probability vs. the number of reflecting elements

Figs. 5 and 6 present the SER vs. SNR. In Fig. 5, the BPSK system is considered and the performance is presented vs. the numbers of reflecting elements. In the simulations, the number of reflecting elements is set to N = 16, N = 64, and N = 100, and we consider BPSK (σ1 = 1, σ2 = 1), 2FSK (σ1=1,σ2=0.715) and 4PSK (σ1=1,σ2=sin2⁡(π4)) modes. It is seen that increasing N greatly improves the SER. As expected, deploying a large number of reflecting elements results in a higher ergodic rate verifying the conclusion drawn from Fig. 3. These observations further suggest that the wireless communication system should use IRS technology. In Fig. 6, we also compare the above three modulation techniques for different numbers of reflecting elements. It is seen that the number of reflecting elements, N, has a significant impact on the system performance. It is also seen that it is close to performance saturation and suffers a trifling performance when the average SNR is 10 dB. In such a condition, the application of the IRS offers higher throughput and more reliable communication.

Figure 5: The binary phase shift keying (BPSK) vs. SNR for different numbers of reflecting elements

Figure 6: The SER vs. SNR for different modulation techniques for N =16 and N =64

5  Summary

We studied the end-to-end performance of an IRS-assisted wireless communication system. To maximize the system’s SNR, we designed the phase shifts of the reflecting elements and derived the optimal reflection phase of the IRS based on the perfect CSI. The exact expression of the p.d.f. of the SNR was also obtained, which follows a non-central Chi-square distribution. By utilizing the p.d.f. of the SNR, we further analytically derived the achievable rate, outage probability, and bit error rate and further confirmed their accuracy through numerical simulation. The obtained results showed that the achievable rate, outage probability, and BER could be boosted by increasing the number of reflecting elements, and the choice of SNR regimes. It was also seen that IRS-assisted transmission effectively improves the received SNR and enables achieving reliable communication at extremely low SNR regimes. These indicate that IRS-assisted wireless communication systems achieve better performance than the existing wireless communication systems.

Acknowledgement: The authors wish to express their appreciation to the reviewers for their helpful suggestions which greatly improved the presentation of this paper. And we would like to express our gratitude to EditSprings (https://www.editsprings.cn) for the expert linguistic services provided.

Funding Statement: This work was supported in part by the Joint Research Fund for Guangzhou University and Hong Kong University of Science and Technology under Grant No. YH202203, the Guangzhou Basic Research Program Municipal School (College) Joint Funding Project, the Research Project of Guizhou University for Talent Introduction under Grant No. [2020]61, the Cultivation Project of Guizhou University under Grant No. [2019]56, the Open Fund of Key Laboratory of Advanced Manufacturing Technology, Ministry of Education under Grant No. GZUAMT2021KF[01], the National Natural Science Foundation of China under Grant Nos. 51978089 and 62171119, the Key R&D Plan of Sichuan Science and Technology Department under Grant No. 22ZDYF2726, the Chengdu Normal University Scientific Research and Innovation Team under Grant Nos. CSCXTD2020B09, ZZBS201907, CS21ZC01, the Open Project of Intelligent Manufacturing Industry Technology Research Institute under Grant No. ZNZZ2208, the National Key Research and Development Program of China under Grant No. 2020YFB1807201, and Key research and development plan of Jiangsu Province under Grant No. BE2021013-3.

Conflicts of Interest: The authors declare that they have no conflicts of interest to report regarding the present study.

References

1. Wang, H., Xu, L., Yan, Z., Gulliver, T. A. (2020). Low-complexity MIMO-FBMC sparse channel parameter estimation for industrial big data communications. IEEE Transactions on Industrial Informatics, 17(5), 3422–3430. https://doi.org/10.1109/TII.2020.2995598

2. Zhang, Z., Xiao, Y., Ma, Z., Xiao, M., Ding, Z. et al. (2019). 6G wireless networks: Vision, requirements, architecture, and key technologies. IEEE Vehicular Technology Magazine, 14(3), 28–41. https://doi.org/10.1109/MVT.2019.2921208

3. Wang, H., Xiao, P., Li, X. (2022). Channel parameter estimation of mmWave MIMO system in urban traffic scene: A training channel-based method. IEEE Transactions on Intelligent Transportation Systems, 1–9. https://doi.org/10.1109/TITS.2022.3145363

4. Liu, H., Li, G., Li, X., Liu, Y., Huang, G. et al. (2022). Effective capacity analysis of STAR-RIS-Assisted NOMA networks. IEEE Wireless Communications Letters, 11(9), 1930–1934. https://doi.org/10.1109/LWC.2022.3188443

5. Tang, W., Li, X., Dai, J. Y., Jin, S., Zeng, Y. et al. (2019). Wireless communications with programmable metasurface: Transceiver design and experimental results. China Communications, 16(5), 46–61. https://doi.org/10.23919/j.cc.2019.05.004

6. Yu, X., Jamali, V., Xu, D., Ng, D. W. K., Schober, R. (2021). Smart and reconfigurable wireless communications: From IRS modeling to algorithm design. IEEE Wireless Communications, 28(6), 118–125. https://doi.org/10.1109/MWC.001.2100145

7. Li, G., Liu, H., Huang, G., Li, X., Raj, B. et al. (2021). Effective capacity analysis of reconfigurable intelligent surfaces aided NOMA network. EURASIP Journal on Wireless Communications and Networking, 2021(1), 1–16. https://doi.org/10.1186/s13638-020-01861-8

8. Li, X., Xie, Z., Chu, Z., Menon, V. G., Mumtaz, S. et al. (2022). Exploiting benefits of IRS in wireless powered NOMA networks. IEEE Transactions on Green Communications and Networking, 6(1), 175–186. https://doi.org/10.1109/TGCN.2022.3144744

9. Han, Y., Tang, W., Jin, S., Wen, C. K., Ma, X. (2019). Large intelligent surface-assisted wireless communication exploiting statistical CSI. IEEE Transactions on Vehicular Technology, 68(8), 8238–8242. https://doi.org/10.1109/TVT.2019.2923997

10. Xu, J., Liu, Y. (2021). A novel physics-based channel model for reconfigurable intelligent surface-assisted multi-user communication systems. IEEE Transactions on Wireless Communications, 21(2), 1183–1196. https://doi.org/10.1109/TWC.2021.3102887

11. Lyu, J., Zhang, R. (2020). Spatial throughput characterization for intelligent reflecting surface aided multiuser system. IEEE Wireless Communications Letters, 9(6), 834–838. https://doi.org/10.1109/LWC.2020.2972527

12. Makarfi, A. U., Rabie, K. M., Kaiwartya, O., Badarneh, O. S., Li, X. et al. (2020). Reconfigurable intelligent surface enabled IoT networks in generalized fading channels. 2020 IEEE International Conference on Communications (ICC), Dublin, Ireland, IEEE.

13. Li, X., Zheng, Y., Zeng, M., Liu, Y., Dobre, O. A. (2022). Enhancing secrecy performance for STAR-RIS NOMA networks. IEEE Transactions on Vehicular Technology, 1–6. https://doi.org/10.1109/TVT.2022.3213334

14. Wu, Q., Zhang, R. (2019). Intelligent reflecting surface enhanced wireless network via joint active and passive beamforming. IEEE Transactions on Wireless Communications, 18(11), 5394–5409. https://doi.org/10.1109/TWC.2019.2936025

15. Wu, Q., Zhang, R. (2019). Beamforming optimization for wireless network aided by intelligent reflecting surface with discrete phase shifts. IEEE Transactions on Communications, 68(3), 1838–1851. https://doi.org/10.1109/TCOMM.2019.2958916

16. Yu, X., Xu, D., Schober, R. (2020). Optimal beamforming for MISO communications via intelligent reflecting surfaces. 2020 IEEE 21st International Workshop on Signal Processing Advances in Wireless Communications (SPAWC), Oulu, Finland, IEEE.

17. Ning, B., Chen, Z., Chen, W., Fang, J. (2020). Beamforming optimization for intelligent reflecting surface assisted MIMO: A sum-path-gain maximization approach. IEEE Wireless Communications Letters, 9(7), 1105–1109. https://doi.org/10.1109/LWC.2020.2982140

18. Huang, C., Zappone, A., Alexandropoulos, G. C., Debbah, M., Yuen, C. (2019). Reconfigurable intelligent surfaces for energy efficiency in wireless communication. IEEE Transactions on Wireless Communications, 18(8), 4157–4170. https://doi.org/10.1109/TWC.2019.2922609

19. You, C., Zheng, B., Zhang, R. (2020). Channel estimation and passive beamforming for intelligent reflecting surface: Discrete phase shift and progressive refinement. IEEE Journal on Selected Areas in Communications, 38(11), 2604–2620. https://doi.org/10.1109/JSAC.2020.3007056

20. Wang, P., Fang, J., Yuan, X., Chen, Z., Li, H. (2020). Intelligent reflecting surface-assisted millimeter wave communications: Joint active and passive precoding design. IEEE Transactions on Vehicular Technology, 69(12), 14960–14973. https://doi.org/10.1109/TVT.2020.3031657

21. Pradhan, C., Li, A., Song, L., Vucetic, B., Li, Y. (2020). Hybrid precoding design for reconfigurable intelligent surface aided mmwave communication systems. IEEE Wireless Communications Letters, 9(7), 1041–1045. https://doi.org/10.1109/LWC.2020.2980225

22. Tan, W., Yang, X., Ma, S. (2021). Spectral efficiency of massive MIMO With LMMSE receivers under finite dimensional channels. IEEE Wireless Communications Letters, 11(1), 18–22. https://doi.org/10.1109/LWC.2021.3118700

23. Basar, E. (2019). Transmission through large intelligent surfaces: A new frontier in wireless communications. 2019 European Conference on Networks and Communications (EuCNC), Valencia, Spain, IEEE.

24. Abramowitz, M., Stegun, I. A. (1964). Handbook of mathematical functions with formulas, graphs, and mathematical tables, vol. 55. New York, USA: US Government printing office.

25. Tan, W., Ma, S. (2022). Antenna array topologies for mmWave massive MIMO systems: Spectral efficiency analysis. IEEE Transactions on Vehicular Technology, 71(12), 12901–12915. https://doi.org/10.1109/TVT.2022.3197600

26. Andrews, L. C. (1998). Special functions of mathematics for engineers, vol. 49. Washington State, USA: SPIE Press.

27. Karagiannidis, G. K., Lioumpas, A. S. (2007). An improved approximation for the Gaussian Q-function. IEEE Communications Letters, 11(8), 644–646. https://doi.org/10.1109/LCOMM.2007.070470

28. Gradshteyn, I. S., Ryzhik, I. M. (2014). Table of integrals, series, and products. San Diego, California, USA: Academic Press.

images
This work is licensed under a Creative Commons Attribution 4.0 International License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.