R.V. Reji, S. Anil Lal^†

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-8, 2016, DOI:10.5098/hmt.7.27

Abstract DSMC simulation of re-entry of an object with shape and size close to that of ISRO’s Space Recovery Experiment (SRE) capsule has been analysed using the open-source tool dsmcFoam for three altitude conditions, viz. 85 km, 100 km and 115 km, and for three angles of attack, viz. 0 o , 20o&40o . The hypersonic free stream velocity of 8000 m/s and boundary surface temperature of 300 K have been used for the simulations. The variation of parameters such as surface heat flux, surface pressure, shear stress, slip velocity, temperature jump and integrals such as More >

P. Chandra Reddy¹, M.C. Raju^1,*, G.S.S. Raju², S.V.K. Varma³

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-11, 2016, DOI:10.5098/hmt.7.28

Abstract The present analysis is focused on free convective heat and mass transfer characteristics of magneto-nanofluid flow through a moving vertical plate in the presence of thermal radiation and thermal diffusion. The water-based nanofluid containing copper is taken into consideration. A uniform magnetic field is applied perpendicular to the plate. The governing equations are solved by applying finite difference method. Numerical results of the fluid velocity, temperature, concentration, shear stress, rate of heat transfer and rate of mass transfer are presented graphically for different values of the physical parameters encountered in the problem. It is noticed More >

S.V. Subhashini^a,* , Nancy Samuel^b

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-7, 2016, DOI:10.5098/hmt.7.29

Abstract The aim of this paper is to present non-similar solutions of a steady laminar compressible boundary layer flow past a long thin circular cylinder including the effects of wall enthalpy and surface mass transfer. The governing equations along with the boundary conditions are first converted into dimensionless form by a non-similar transformation, and then the resulting system of coupled non-linear partial differential equations is solved by an implicit finite difference scheme in combination with the quasi-linearization technique. The increase in the value of power law variation of viscosity causes an increase in the boundary layer More >

Niki Rezazadeh, Rezvan Abdi^*

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-6, 2016, DOI:10.5098/hmt.7.30

Abstract This study investigates the heat transfer in the mode of natural convection from a pair of hot cylinders to a cold square enclosure. Effects of boundary conditions of the enclosure on the rate of heat transfer from a pair of isothermal hot cylinders are investigated at a Rayleigh number of 10⁵ . The cylinders are arranged in a horizontal array at the middle height of enclosure. The commercial software, Fluent (V.6.3.26), is utilized to solve the problem using the Finite Volume Method. The streamlines as well as isothermal lines of the problem are reported. Moreover, the More >

Dave Martin^a,b,† , Hicham Chaouki^a,b, Jean-Loup Robert^a, Donald Ziegler^c, Mario Fafard^a,b

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-9, 2016, DOI:10.5098/hmt.7.31

Abstract The two dimensional phase change problem was solved using the extended finite element method with a Lagrange formulation to apply the interface boundary condition. The Lagrange multiplier space is identical to the solution space and does not require stabilization. The solid-liquid interface velocity is determined by the jump in heat flux across the i nterface. Two methods to calculate the jump are used and c ompared. The first is based on an averaged temperature gradient near the interface. The second uses the Lagrange multiplier values to evaluate the jump. The Lagrange multiplier based approach was More >

Odelu Ojjela^*, K. Pravin Kashyap, N. Naresh Kuma, Samir Kumar Das

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-9, 2016, DOI:10.5098/hmt.7.32

Abstract This article presents an unsteady incompressible Upper Convected Maxwell (UCM) fluid flow with temperature dependent thermal conductivity between parallel porous plates which are maintained at different temperatures varying periodically with time. Assume that there is a periodic suction and injection at the upper and lower plates respectively. The governing partial differential equations are reduced to non linear ordinary differential equations by using similarity transformations and the solution is obtained using differential transform method. The effects of various fluid and geometric parameters on the velocity components, temperature distribution and skin friction are discussed in detail through More >

Mohammad Hasan Khademi^a,*, Abbas Mozafari^b

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-8, 2016, DOI:10.5098/hmt.7.33

Abstract An integral energy equation model is used to calculate the heat transfer coefficient/Nusselt number, thermal boundary layer thickness and temperature distribution in the turbulent boundary layer for forced convection over a smooth flat plate. The proposed model is based on two polynomial temperature profiles in a thermal laminar sublayer as well as in a fully developed boundary layer and two integral energy equations. The performance of this new model is compared with the most commonly used semi-empirical correlations and the complex established models such as k-ε, k-ω, RSM, and a good agreement is achieved. More >

Jacob Thottathil Varghese^a,*, Sat Ghosh^a,b

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-7, 2016, DOI:10.5098/hmt.7.34

Abstract Nature has its own astonishing capabilities to cleanse polluted environment. Living green drapes on buildings look elegant providing sustainable solutions in congested metropolises. VIT University promotes green values within the country. The walls of a subway connecting the main campus and hostel premises are draped with Vernonia elaeagnifolia, which was found to be efficient in capturing vehicular pollution. An experimental study established deposition patterns of pollutants. Thereafter, diffusive uptake modelling elucidated the mechanistic details of mass transport through the plant tissues. It is expected that the results of this paper will promote the use of green More >

A. Zoubir^a , R. Agounoun^a,*, I. Kadiri^b, K. Sbai^a , M. Rahmoune^a

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-6, 2016, DOI:10.5098/hmt.7.35

Abstract Boiling heat transfer process is important because it is a way to increase the flux density transmitted at low temperature differences. To quantify the thermal exchanges, we performed an experimental study of the nitrogen pool boiling, in transient conditions, on a horizontal brass ribbon for a fixed flux density. The results show that there is no break between the monophasic convection zone and the nucleated boiling region. In the nucleated boiling zone, the temperature variations are very small. We also note that the overheating required to trigger boiling increases with the time delay after the More >

Xiaoqian Ma^a , Mo Yang^a,*, Yuwen Zhang^b

Frontiers in Heat and Mass Transfer, Vol.7, pp. 1-8, 2016, DOI:10.5098/hmt.7.36

Abstract Combustion mechanism of a 300 MW pulverized coal boiler is analyzed and the optimization of the performance of the boiler is carried out. The flow field, temperature field, devolatilization, char combustion and CO generation in the boiler furnace under actual condition is obtained by using Fluent. Three methods to improve the efficiency of boiler combustion are proposed based on the pulverized coal combustion mechanism; their feasibilities are verified through numerical simulation and analysis. The three proposed methods to increase the combustion efficiency may give theoretical reference for air arrangement and combustion optimization of the same More >