Brahim DENNAI^1*, Mohammed EL Bizani BELBOUKHARI¹ , Tawfiq CHEKIFI¹, Rachid KHELFAOUl¹

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.3, pp. 102-110, 2016, DOI:10.3970/fdmp.2016.012.102

Abstract Microfluidic systems are used and exploited in various fields, as they are highly specific and developed in their use. The micro devices are used in various analyzes of medical disciplines, chemical and other fields. Our research team "MAAt" within ENERGARID laboratory is in the process of triggered several lines of research in this area, the micro-mixing, separation of micro particles, droplet production. For that, we need tools and micro devices to study the phenomena.. In this work, we present a theoretical study and numerical simulation of micro device (micro diode Tesla). A Diode Tesla is More >

Hayder A. Abdulbari ^1,2, Hassan D. Mahammed¹, Z. Hassan, Wafaa K. Mahmood³

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.2, pp. 86-101, 2016, DOI:10.3970/fdmp.2016.012.086

Abstract An experimental investigation was carried out to study the response of a turbulent pressure drop fluctuations to longitudinal groove riblets, involved two configurations being triangular and spaced triangular grooves with height 600, 800, 1000 μm and peak to peak spacing 1000 μm and 2000 μm respectively. Experiments were therefore performed at free stream velocity up to 0.44 m/sec, which were corresponding to Reynolds number (Re) 53000. The development of the obtained turbulent layer downstream of the grooves was then compared with the results from the corresponding smooth-wall case. To conclude, the effect of the spaced More >

Antoine Fabre¹, Jordan Hristov^2*, Rachid Bennacer¹

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.2, pp. 69-85, 2016, DOI:10.3970/fdmp.2016.012.069

Abstract Closed form approximate solutions to nonlinear transient heat conduction with linear power-law k = k₀(1±βT^m) temperature-dependent thermal diffusivity have been developed by the integral-balance integral method under transient conditions. The solutions use improved direct approaches of the integral method and avoid the commonly used linearization by the Kirchhoff transformation. The main steps in the new solutions are improvements in the integration technique of the double-integration technique and the optimization of the exponent of the approximate parabolic profile with unspecified exponent. Solutions to Dirichlet boundary condition problem have been developed as examples by the classical Heat-balance Integral More >

Meryem NAOUM¹, Mustapha EL ALAMI²

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.2, pp. 56-68, 2016, DOI:10.3970/fdmp.2016.012.056

Abstract A numerical study of mixed convection from a U-shaped channel is carried out. The flow is considered two dimensionnel. The inlet opening is adjusted in the right vertical part of the channel, while the outlet one is placed on the left vertical part. Navier–Stokes equations are solved using a control volume method and the SIMPLEC algorithm is considered for the treatment of pressure–velocity coupling. Special emphasis is given to detail the effect of the Reynolds and Rayleigh numbers on the heat transfer generated by mixed convection. The results are given for the parameters of control More >

M. Zitoune^{1, 2} , O. Ourrad Meziani², B. Meziani², M. Adnani^{1, 2}

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.1, pp. 33-55, 2016, DOI:10.3970/fdmp.2016.012.033

Abstract A finite volume code used for detailed analysis of forced-convection flow in a horizontal channel containing eight heat sources simulating electronic components. The study deals the effect of variations of Reynolds number, the volume fraction and the good choice of type of nanoparticles added to the base fluid. The study shows that the rate of heat transfer increases with increasing Reynolds number and the volume fraction of nanofluids but not infinitely. The analysis of the dynamic and thermal field shows that the heat transfer is improved, with the increase in the Reynolds number and the More >

M. Bouzaid¹, M. Oubrek, O. Ansari, A. Sabri, M. Taha-Janan

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.1, pp. 15-32, 2016, DOI:10.3970/fdmp.2016.012.015

Abstract Fresh water available on earth is very scared. Yet the demand of fresh water is incessantly increasing, due to population growth and rapid industrialization. According to the United Nations, in 2025, 63% of the world’s population will be living in scarce water areas. The provision of freshwater is becoming a gradually more important issue in many areas of the world. Oceans are the only available source for large amount of water. Ocean water presents high salinity, so there is a need to desalinate ocean water for everyday consumption. Solar stills are widely used in solar… More >

ADNANI Massinissa¹, MEZIANI Bachir², OURRAD Ouerdia², ZITOUNE Mounir¹

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.1, pp. 1-14, 2016, DOI:10.3970/fdmp.2016.012.001

Abstract A numerical study of natural convection in a square cavity subjected to the thermals boundary conditions on the sidewalls is presented and discussed. The fluid is Newtonian and equations governing the flow field and the heat transfer are given in dimensionless form. The finite volume method was adopted to solve the algebraic system. Influence of the Prandtl and the Rayleigh numbers on heat transfer and the flow field is illustrated and discussed as the stream functions, isotherms, horizontal velocity, local and average Nusselt numbers. Results indicate that improved heat transfer is more pronounced with increasing More >

N. Laaroussi^1*, Y. Chihab¹, M. Garoum¹, L-V. Bénet², F. Lacroux³

FDMP-Fluid Dynamics & Materials Processing, Vol.11, No.4, pp. 354-365, 2015, DOI:10.3970/fdmp.2015.011.354

Abstract This study is based on the modeling of the air flow in the hall building including heating and air-conditioning systems. The building contains two converter stations “valves” considered as heat sources. Heat transfer in the hall is numerically simulated using the standard k-ε model of turbulence. For a very hot weather, this study aims to evaluate the local temperatures in the ambient air of the hall, with assuming running valves and air conditioning device in open loop with a 35°C inlet temperature. The study has shown that the air conditioning is efficient enough to maintain More >

SouadMorsli^1,*, Amina Sabeur¹, Mohammed El Ganaoui²

FDMP-Fluid Dynamics & Materials Processing, Vol.11, No.4, pp. 342-353, 2015, DOI:10.3970/fdmp.2015.011.342

Abstract The aim of this work is the numerical simulation of the combustion of hydrogen with air in a burner and the numerical solution of local entropy generation rate in the combustion chamber. The effects of equivalence ratio φ and oxygen percentage γ on combustion and entropy generation rates are studied for different φ(ranging from 0 to 1.0) and γ values (ranging from 10 to 30%). The predictions show that the increase of φ (or the decrease of λ ) reduces notably the reaction rate levels. The equations of continuity, of energy and momentum are solved by More >

R. Savino¹, M . Visone², D. Rossetto³, V. D'Oriano⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.11, No.4, pp. 331-341, 2015, DOI:10.3970/fdmp.2015.011.331

Abstract This paper presents two applications of Computational Fluid Dynamics (CFD) to super and mega yacht design, based on the Volume of Fluid method. After an overview of recent literature on the subject, the analysis of the hydrodynamic performances of different hull configurations and of different appendage configurations is presented. More >