Lina Gogoi¹, Rumi Narzari¹, Nirmali Gogoi², Muhammad Farooq³, Rupam Kataki^1,*

Phyton-International Journal of Experimental Botany, Vol.88, No.4, pp. 349-365, 2019, DOI:10.32604/phyton.2019.08406

Abstract The increasing deforestation with an alarming rate is the prime cause of upsetting the balance in the natural ecosystem and the livelihood of local communities. Sustainable forest management and reforestation efforts can equilibrium this destruction and maintain the protected areas. In this regard, soil management strategies for reforestation of the degraded forest land can be helpful. In this review, the potential of using biochar, a solid carbon rich product of biomass thermochemical conversion, as a soil amendment in forest soils has been discussed. The production procedures of biochar, availability of feedstocks and the biochar properties More >

Haiyang Ding¹, Xiaohua Yang¹, Lina Xu¹, Mei Li¹, Shouhai Li¹, Jianling Xia^1,*

Journal of Renewable Materials, Vol.7, No.12, pp. 1391-1401, 2019, DOI:10.32604/jrm.2019.07207

Abstract A water-soluble lubricant additive (RSOPE) was prepared by esterification reaction using fatty acid from rubber seed oil. The RSOPE was added into water-ethylene glycol (W-EG) solution as lubricant additive. Dispersion stability and rheological properties were investigated. We used a four-ball tribotester to assess the lubrication performance of W-EG based fluid with the RSOPE additive. The stainless-steel surface was analyzed using scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). Good dispersion stability was observed in the RSOPE/W-EG solutions. Furthermore, nonNewtonian fluid behavior at low shear rates and Newtonian fluid behavior at high shear rates was More >

Jie Xu^1,3, Jiayao Yang¹, Peng Lin², Xiaohuan Liu^1,*, Jinjie Zhang¹, Shenyuan Fu^1,*, Yuxun Tang^2,*

Journal of Renewable Materials, Vol.7, No.12, pp. 1333-1346, 2019, DOI:10.32604/jrm.2019.07905

Abstract It is essential to design economic and efficient tougheners to prepare high-performance epoxy resin; however, this has remained a huge challenge. Herein, an eco-friendly, low-cost, and facile-fabricated bio-based hyperbranched toughener, carboxylic acid-functionalized tannic acid (CATA), was successfully prepared and applicated to the preparation of solvent-free epoxy resins. The mechanical performance, morphology, structural characterization, and thermal characterization of toughened epoxy resin system were studied. The toughened epoxy resin system with only 1.0wt% CATA reached the highest impact strength, 111% higher than the neat epoxy resin system. Notably, the tensile strength and elongation at break of toughened More >

Xiaoliang Zhao^1,#, Yuting Wang^1,#, Xiuying Pu¹, Jianzhong Ma¹, Feifan Leng¹, Yonggang Wang¹, Yanling Wang¹, Shuhong Yang¹, Fen Ran², Weijie Zhang^1,*

Journal of Renewable Materials, Vol.7, No.12, pp. 1321-1332, 2019, DOI:10.32604/jrm.2019.07757

Abstract A series of the Guiqi polysaccharides/chitosan/alginate composite hydrogel microspheres (GPcM) with different particle sizes were prepared with Guiqi polysaccharides (GP), chitosan (CS) and sodium alginate (Alg). The optimum preparation process was also determined by single factor and orthogonal experiment analysis. The GPcM were characterized by fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), drug loading efficiency test (LE), encapsulation efficiency test (EE) and in vitro release study. The results showed that the Guiqi polysaccharides chitosan hydrogel (GPCH) and sodium alginate hydrogel (SAH) formed a crossover system in GPcM. The GPcM have a uniform particle More >

Yongfang Zhang^1,2, Wensheng Hou¹, Hong Guo¹, Sheng Shi¹, Jinming Dai^1,2,*

Journal of Renewable Materials, Vol.7, No.12, pp. 1309-1319, 2019, DOI:10.32604/jrm.2019.07884

Abstract Carbon microspheres were prepared from waste cotton fibers by hydrothermal carbonization (HTC) with the addition of copper sulphate in this work. The important influence factors, temperature, concentration of copper sulphate, resident time were explored here. The smooth and regular carbon microspheres could be formed at 330°C with 0.15 wt% copper sulphate after 6 h from waste cotton fibers. The crystal structures of cotton fibers were destructed in a short resident time with 0.15 wt% copper sulphate from SEM images and XRD patterns of solid products. This strategy provides a new, mild and efficient method to… More >

Narsimha Pandi¹, Shirish H. Sonawane^1,*, Sarang P. Gumfekar², Anand Kishore Kola¹, Pramod H. Borse³, Swapnil B. Ambade⁴, Sripadh Guptha¹, Muthupandian Ashokkumar⁵

Journal of Renewable Materials, Vol.7, No.12, pp. 1279-1293, 2019, DOI:10.32604/jrm.2019.07609

Abstract The present study deals with the intensified synthesis of starchpolyaniline (starch-PANI) nanocomposite using an ultrasound-assisted method. Starch is a key component in this nanocomposite, which acts as a backbone of the nucleation of PANI. The Electrochemical property of the nanocomposite arises due to the addition of PANI. This is one of green approach for the synthesis of bio nanocomposite using ultrasound. The crystallinity of the composite is evaluated using the Scherrer Formula. The starch-PANI nanocomposite was characterized by XRD, FT-IR, Raman, XPS and TEM. The composite nanoparticles show spherical morphology. The elemental composition of starch-PANI More >

Yixiong Yu^*

Sound & Vibration, Vol.53, No.5, pp. 237-243, 2019, DOI:10.32604/sv.2019.07887

Abstract Mining aeroengine operational data and developing fault diagnosis models for aeroengines are to avoid running aeroengines under undesired conditions. Because of the complexity of working environment and faults of aeroengines, it is unavoidable that the monitored parameters vary widely and possess larger noise levels. This paper reports the extrapolation of a diagnosis model for 20 gas path faults of a double-spool turbofan civil aeroengine. By applying support vector machine (SVM) algorithm together with genetic algorithm (GA), the fault diagnosis model is obtained from the training set that was based on the deviations of the monitored More >

Cheng Hu^*

Sound & Vibration, Vol.53, No.5, pp. 199-206, 2019, DOI:10.32604/sv.2019.07712

Abstract Taking the complex mechanical systems as the research project, a theoretical multi-degree-of-freedom (MDOF) model was established. Based on the vibration characteristics analysis of this system, a novel method of vibration mitigation was proposed, which can be applied to most of the complex mechanical systems. Through this method, limited grounding stiffness was made use of and added to certain degree of freedom (DOF) discretely. Thus, the root-meansquare (RMS) of the systems amplitude can be reduced to ideal level. The MATLAB code based on this method was attached, which was tested on the theoretical model. Consider that More >

Mohd. Ahmed^1,*, Mohamed Hechmi El Ouni¹, Devinder Singh², Nabil Ben Kahla¹

CMES-Computer Modeling in Engineering & Sciences, Vol.121, No.2, pp. 687-786, 2019, DOI:10.32604/cmes.2019.06886

Abstract The paper presents a parametric study on interpolation techniques based postprocessed error estimation in finite element elastic analysis by varying important parameters of recovery, interpolation scheme and type of patch construction. The quality of error estimation with recovery parameters is compared in terms of local and global effectivity of error estimation, rate of error convergence, and adaptively refined meshes. A mesh free moving least square interpolation technique with proven reliability and effectivity is introduced for improving the recovery of finite element solution errors. The post-processed finite element solutions of elastic problems are presented for performance More >

Felipe J. Torres^1,*, Gerardo V. Guerrero², Carlos D. García², Ricardo Zavala-Yoe³, Mario A. García¹, Adolfo R. López⁴

CMES-Computer Modeling in Engineering & Sciences, Vol.121, No.2, pp. 609-630, 2019, DOI:10.32604/cmes.2019.07153

Abstract A complete modeling (including the actuator dynamics) of a robot manipulator that uses three-phase induction motors is presented in this paper. A control scheme is designed to synchronize robot manipulators actuated by induction motors under a masterslave scheme in the case where the joint velocity of the slave robots is estimated. All of the research on the synchronization of robot manipulators assumes the use of ideal actuators to drive the joints; for that reason, in this work, a three-phase induction motor is considered to be a direct-drive actuator for each joint. An entire model of… More >