DIBYENDU S. BAG^*, SHILPI TIWARI, AKANSHA DIXIT, KM. MEENU

Journal of Polymer Materials, Vol.40, No.1-2, pp. 105-123, 2023, DOI:10.32381/JPM.2023.40.1-2.9

Abstract In this paper, we report the microstructural investigation and influence of H-bonding on the thermal behavior e.g., glass transition (T_g ) and thermal degradation of chiral copolymers of (R)- N-(1-phenyl-ethyl) methacrylamide (R-NPEMAM) and 2-hydroxy ethyl methacrylate (HEMA). The T_g increases with the increase of chiral unit content in the copolymers and then attains optimum at around 25 mole % of chiral content. Thereafter it decreases with the increase of chiral content. The effect of copolymer composition and secondary interaction associated with the Hbonding on the thermal properties of these copolymers was also studied. Secondary interaction, specifically H-bonding has been interpreted… More >

HADIMANI SHIVAKUMAR¹, GURUMURTHY G. D.¹, BOMMEGOWDA K. B.², S. PARAMESHWARA³

Journal of Polymer Materials, Vol.40, No.1-2, pp. 93-103, 2023, DOI:10.32381/JPM.2023.40.1-2.8

Abstract Polymer composites are increasing in demand in energy storage applications including in the electronic as well as electrical industries due to the ease of processing of these materials with associated advantages like light weight, corrosion resistance, and high mechanical strength. In this investigation, efforts are made to enhance the charging and discharging properties of epoxy/carbon fabric composite by the addition of graphene nanoplatelets (GNPs) into the epoxy/ carbon matrix. The performance of the composites with graphene platelets of 0.5 to 5 wt. % in epoxy were characterized and 1wt.% percolation threshold was observed poor performance in gravimetric charge and discharge… More >

FOUED KHOFFI^1,*, OMAR HARZALLAH², JEAN YVES DREAN²

Journal of Polymer Materials, Vol.40, No.1-2, pp. 59-69, 2023, DOI:10.32381/JPM.2023.40.1-2.5

Abstract The aim of this study is to analyze the interfacial and the frictional properties of copper (Cu) reinforced polyethylene terephthalate (PET) filament. This Cu-Embedded PET filament will be used as an information transmitter. This filament was prepared by a co-extrusion process. Mechanical properties of these filaments have been quantified by tensile and pull-out analyses. It is shown that the mechanical properties of composite filament were improved by adding the copper filament (from 0.82 to 1.2 GPa). The results of the pull-out test revealed some adhesion between the copper and the PET despite the existence of a slippage of the copper… More >

Ran Wang¹, Aimin Gong^1,*, Shanqing Shao¹, Baoli Qu², Jing Xu³, Fulai Wang¹, Feipeng Liu^3,*

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.4, pp. 749-769, 2024, DOI:10.32604/fdmp.2023.042566

Abstract The mechanical properties of cementitious sand and gravel damming material have been experimentally determined by means of microscopic SEM (Scanning Electron Microscopy) image analysis. The results show that the combination of fly ash and water can fill the voids in cemented sand and gravel test blocks because of the presence of hydrated calcium silicate and other substances; thereby, the compactness and mechanical properties of these materials can be greatly improved. For every 10 kg/m³ increase in the amount of cementitious material, the density increases by about 2%, and the water content decreases by 0.2%. The amount of cementitious material used… More > Graphic Abstract

Aravind Sathyanarayana^a, Pramod Warrier^b, Yogendra Joshi^a,*, Amyn Teja^b

Frontiers in Heat and Mass Transfer, Vol.2, No.4, pp. 1-7, 2011, DOI:10.5098/hmt.v2.4.3007

Abstract Electrical and chemical compatibility requirements of electronic components pose significant constraints on the choice of liquid coolants. Dielectric coolants such as Novec fluids and fluoroinerts are plagued by poor thermal properties. This necessitates the development of new heat transfer fluids. In this study we examine mixture formulations that provide an avenue for enhancing the properties of existing heat transfer fluids. Mixture formulations of Novec fluid (HFE 7200) with Methanol and Ethoxybutane are considered. Pool boiling experiments are performed on a copper nanowire surface. The results show an improvement of 24% and 11% in the CHF of HFE 7200 – Methanol… More >

REZA YADOLLAHVANDMIANDOAB^1,#, MEHRSA JALALIZADEH^1,#, FRANCIELE APARECIDA VECHIA DIONATO¹, KEINI BUOSI¹, PATRÍCIA A. F. LEME¹, LUCIANA S. B. DAL COL¹, CRISTIANE F. GIACOMELLI¹, ALEX DIAS ASSIS¹, NASIM BASHIRICHELKASARI¹, LEONARDO OLIVEIRA REIS^1,2,*

Oncology Research, Vol.32, No.4, pp. 597-605, 2024, DOI:10.32604/or.2024.045442

Abstract Bladder cancer (BC) is the 10th most common cancer worldwide, with about 0.5 million reported new cases and about 0.2 million deaths per year. In this scoping review, we summarize the current evidence regarding the clinical implications of single-cell sequencing for bladder cancer based on PRISMA guidelines. We searched PubMed, CENTRAL, Embase, and supplemented with manual searches through the Scopus, and Web of Science for published studies until February 2023. We included original studies that used at least one single-cell technology to study bladder cancer. Forty-one publications were included in the review. Twenty-nine studies showed that this technology can identify… More > Graphic Abstract

M. Yakut Ali^a,*, Fanghao Yang^a, Ruixian Fang^a, Chen Li^a, Jamil Khan^a,†

Frontiers in Heat and Mass Transfer, Vol.2, No.3, pp. 1-11, 2011, DOI:10.5098/hmt.v2.3.3003

Abstract This study experimentally investigates single phase heat transfer and pressure drop characteristics of a shallow rectangular microchannel heat sink whose surface is enhanced with copper nanowires (CuNWs). The hydraulic diameter of the channel is 672 μm and the bottom wall is coated with Cu nanowires (CuNWs) of 200 nm in diameter and 50 μm in length. CuNWs are grown on the Cu heat sink by electrochemical synthesis technique which is inexpensive and readily scalable. The heat transfer and pressure drop results of CuNWs enhanced heat sink are compared with that of bare copper surface heat sink using deionized (DI) water… More >

Etienne Costa-Patry^a, Jonathan Olivier^b, John R. Thome^a,∗

Frontiers in Heat and Mass Transfer, Vol.3, No.1, pp. 1-14, 2012, DOI:10.5098/hmt.v3.1.3002

Abstract This article presents new experimental results for two-phase flow boiling of R-134a, R-1234ze(E) and R-245fa in a micro-evaporator. The test section was made of copper and composed of 52 microchannels 163μm wide and 1560μm high with the channels separated by 178μm wide fins. The channels were 13.2mm long. There were 35 local heaters and temperature measurements arranged in a 5×7 array as a pseudo-CPU. The total pressure drops of the test section were below 20kPa in all cases. The wall heat transfer coefficients were generally above 10’000W/m²K and a function of the heat flux, vapor quality and mass flux. A… More >

Mohamed S. El-Genk^a,b,c,∗, Amir F. Ali^a,c

Frontiers in Heat and Mass Transfer, Vol.3, No.4, pp. 1-14, 2012, DOI:10.5098/hmt.v3.4.3001

Abstract Advanced spreaders for cooling a 10 x 10 mm underlying computer chip with a central hot spot (CHS) could remove > 85 W of dissipated thermal power at junctions’ temperature < 100o C. The spreaders comprise a 1.6 - 3.2 mm thick Cu substrate and an 80-μm thick micro-porous copper (MPC) surface cooled by saturation nucleate boiling of PF-5060 dielectric liquid. Investigated are the effects of varying the heat flux at the chip’s 1 and 4 mm² CHS and the impedance of thermal interface material (TIM) between the Cu substrate and underlying chip. Results confirmed the effectiveness of the MPC… More >

Wuyang Fan, Shisheng Zhong^*

CMES-Computer Modeling in Engineering & Sciences, Vol.139, No.3, pp. 2525-2555, 2024, DOI:10.32604/cmes.2023.046951

Abstract The dynamic balance assessment during the assembly of the coordinator gyroscope significantly impacts the guidance accuracy of precision-guided equipment. In dynamic balance debugging, reliance on rudimentary counterweight empirical formulas persists, resulting in suboptimal debugging accuracy and an increased repetition rate. To mitigate this challenge, we present a multi-head residual graph attention network (ResGAT) model, designed to predict dynamic balance counterweights with high precision. In this research, we employ graph neural networks for interaction feature extraction from assembly graph data. An SDAE-GPC model is designed for the assembly condition classification to derive graph data inputs for the ResGAT regression model, which… More >