K.Udaya Bhaskar^1,2, Sumit Tiwari², N. Ramakrishnan²

CMC-Computers, Materials & Continua, Vol.2, No.1, pp. 13-22, 2005, DOI:10.3970/cmc.2005.002.013

Abstract The investigation pertains to establishing a simulation methodology for understanding the separation characteristics of a typical hydrocyclone where the work was carried out using a commercially available CFD software. The studies included water flow profiles, water throughput {\&} product split, particle distribution etc. and the simulated results are further validated with suitably performed experiments. The work essentially highlights the performance of the hydrocyclone using numerical studies where water is used as a primary phase and solid particles as secondary ones. This methodology is expected to be useful in the design of hydrocyclones and optimizing the More >

Dimitrios Tziakas¹, Georgios Chalikias¹, John T. Parissis², Helen Hatzinikolaou¹, Dimitrios Stakos¹, Evropi Papadopoulou³, Alexandros Kortsaris³, Dimitrios Hatseras¹

European Cytokine Network, Vol.15, No.3, pp. 231-239, 2004

Abstract Introduction. Recent clinical and experimental studies indicate that upregulation of the TNF system can contribute to the progression of cardiac remodeling and heart failure decompensation, by promoting alterations in cardiomyocyte biology and extracellular matrix metabolism. Extracellular matrix turnover is regulated by the matrix metalloproteinases (MMPs), which are endogenous enzymes responsible for extracellular collagen degradation. The present study investigates the fluctuation of serum levels of TNF-α, soluble TNF receptor-1 (sTNFR1) and -2 (sTNFR2), in patients with chronic heart failure both during acute decompensation and the stable state of the syndrome. The second goal of this study… More >

N. D. Ngo, K. K. Tamma

CMES-Computer Modeling in Engineering & Sciences, Vol.5, No.2, pp. 103-134, 2004, DOI:10.3970/cmes.2004.005.103

Abstract In the process modeling and manufacturing of large geometrically complex structural net-shaped components comprising of fiber-reinforced composite materials by Resin Transfer Molding (RTM), a polymer resin is injected into a mold cavity filled with porous fibrous preforms. The overall success of the manufacturing process depends on the complete impregnation of the fiber preform by the polymer resin, prevention of polymer gelation during filling, and subsequent avoidance of dry spots. Since the RTM process involves the injection of a cold resin into a heated mold, the associated physics encompasses a moving boundary value problem in conjunction More >

Jun Wang¹, Wei Huang², Raghbir S. Bhullar³, Pin Tong²

Molecular & Cellular Biomechanics, Vol.1, No.2, pp. 161-168, 2004, DOI:10.3970/mcb.2004.001.161

Abstract Surface-tension-driven blood flow into a capillary tube, as in some medical devices, is studied. In a previous article, we considered the early stages of the entry flow from a drop of blood into a capillary, and solved the problem analytically under the assumption that the resistance of the air is negligible. In the present note we consider a capillary tube of finite length, with the far end containing a small window which opens to the atmosphere. The dynamic reverberation of the air in the capillary tube is analyzed in conjunction with the dynamics of the… More >

Dan Givoli¹

CMES-Computer Modeling in Engineering & Sciences, Vol.5, No.6, pp. 497-514, 2004, DOI:10.3970/cmes.2004.005.497

Abstract Very thin layers with material properties which significantly differ from those of the surrounding medium appear in a variety of applications. Traditionally there are two extreme ways of handling such layers in finite element analysis: either they are fully modelled or they are totally ignored. The former option is often very expensive computationally, while the latter may lead to significant inaccuracies. Here a special technique of modeling thin layers is devised within the framework of the finite element method. This technique constitutes a prudent compromise between the two extremes mentioned above. The layer is replaced More >

E. Ferretti ¹

CMES-Computer Modeling in Engineering & Sciences, Vol.6, No.5, pp. 453-476, 2004, DOI:10.3970/cmes.2004.006.453

Abstract The Cell Method (CM) code with automatic remeshing for crack propagation analysis [Ferretti (2003)] is here used for modeling the pullout test. Particular emphasis is given to the analysis in the Mohr-Coulomb plane, since previous numerical models were not decisive in describing failure mechanism in pullout tests. The interpretations of experimental and analytical studies vary widely, and none of the existing explanations offer a complete description of the progressive failure of the concrete medium [Yener (1994)]. Nor do most existing interpretations appear to be totally compatible with the experimental evidence. Analysis of the failure mechanism… More >

Z.Y. Qian¹, Z.D. Han¹, S.N. Atluri¹

CMES-Computer Modeling in Engineering & Sciences, Vol.6, No.1, pp. 115-122, 2004, DOI:10.3970/cmes.2004.006.115

Abstract This article has no abstract. More >

P. Raghavan¹, S. Ghosh²

CMES-Computer Modeling in Engineering & Sciences, Vol.5, No.2, pp. 151-170, 2004, DOI:10.3970/cmes.2004.005.151

Abstract This paper presents an adaptive multi-level computational model that combines a conventional displacement based finite element model with a microstructural Voronoi cell finite element model for multi-scale analysis of composite structures with non-uniform microstructural heterogeneities as obtained from optical or scanning electron micrographs. Three levels of hierarchy, with different resolutions, are introduced in this model to overcome shortcomings posed by modeling and discretization errors. Among the three levels are: (a) level-0 of pure macroscopic analysis; (b) level-1 of macro-micro coupled modeling, used for signaling the switch over from macroscopic analyses to pure microscopic analyses; and More >

Spandan Maiti¹, Philippe H. Geubelle¹

CMES-Computer Modeling in Engineering & Sciences, Vol.5, No.2, pp. 91-102, 2004, DOI:10.3970/cmes.2004.005.091

Abstract The dynamic propagation and branching of a mode I crack in polycrystalline brittle materials like ceramics are investigated numerically using a 2-D explicit grain-based cohesive/volumetric finite element scheme. The granular microstructure of the ceramics is taken into account and the crack is restricted to propagate along the grain boundaries. Special emphasis is placed on studying the effect of grain size and cohesive parameters on the crack branching instability. More >

Peter W. Chung¹, Raju R. Namburu², Brian J. Henz³

CMES-Computer Modeling in Engineering & Sciences, Vol.5, No.1, pp. 45-62, 2004, DOI:10.3970/cmes.2004.005.045

Abstract A method is developed based on an additive modification to the first Lagrangian elasticity tensor to make the finite element method for hyperelasticity viable at the atomic length scale in the context of lattice statics. Through the definition of an overlap region, the close-ranged atomic interaction energies are consistently summed over the boundary of each finite element. These energies are subsequently used to additively modify the conventional material property tensor that comes from the second derivative of the stored energy function. The summation over element boundaries, as opposed to atom clusters, allows the mesh and More >