A. Rasekh^a,*, D.D. Ganji^b, S. Tavakoli^b

Frontiers in Heat and Mass Transfer, Vol.3, No.4, pp. 1-6, 2012, DOI:10.5098/hmt.v3.4.3003

Abstract The present paper deals with the analysis of boundary layer flow and heat transfer of a nanofluid over a stretching circular cylinder in the presence of non-uniform heat source/sink. The governing system of partial differential equations is converted to ordinary differential equations by using similarity transformations, which are then solved numerically using the Runge–Kutta–Fehlberg method with shooting technique. The solutions for the temperature and nanoparticle concentration distributions depend on six parameters, Prandtl number Pr, Lewis number Le, the Brownian motion parameter Nb, the thermophoresis parameter Nt, and non-uniform heat generation/absorption parameters A*, B*. Numerical results are presented both… More >

Massimo Corcione¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 175-200, 2011, DOI:10.3970/fdmp.2011.007.175

Abstract Free convection heat transfer in nanofluids from horizontal isothermal cylinders is investigated theoretically. The main idea upon which the present work is based is that nanofluids behave more like a single-phase fluid rather than like a conventional solid-liquid mixture. This assumption implies that all the convective heat transfer correlations available in the literature for single-phase flows can be extended to nanoparticle suspensions, provided that the thermophysical properties appearing in them are the nanofluid effective properties calculated at the reference temperature. In this connection, two empirical equations, based on a wide variety of experimental data reported… More >

R. J. Johnson^∗, R. Pitchumani^†

Frontiers in Heat and Mass Transfer, Vol.1, No.1, pp. 1-9, 2010, DOI:10.5098/hmt.v1.1.3007

Abstract Much research is currently being performed with carbon nanotube additives to neat resin systems to enhance properties such as thermal and electrical conductivity, strength, modulus and damping. Fabrication of parts based on carbon nanotube filled resin systems requires information on their cure kinetics and rheology, which has been relatively less studied so far. This work presents an extensive experimental study that systematically characterizes the cure kinetics and viscosity as a function of degree of cure and temperature of EPON 815C/EPICURE 3274 epoxy resin system laden with carbon nanotubes. Studies are conducted to determine the effects More >

A. Arefmanesh¹, M. Najafi², M. Nikfar³

CMES-Computer Modeling in Engineering & Sciences, Vol.69, No.2, pp. 91-118, 2010, DOI:10.3970/cmes.2010.069.091

Abstract Procuring a numerical solution through an application of the meshless local Petrov-Galerkin method (MLPG) on the fluid flow and mixed convection in a complex geometry cavity filled with a nanofluid is the scope of the present study. The cavity considered is a square enclosure having a lower temperature sliding lid at the top, a differentially higher temperature wavy wall at the bottom, and two thermally insulated walls on the sides. The nanofluid medium used is a water-based nanofluid, Al₂O₃-water with various volume fractions of its solid. To carry out the numerical simulations, the developed governing equations… More >

A. Podolny^1,2, A. Nepomnyashchy³, A. Oron⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.6, No.1, pp. 13-40, 2010, DOI:10.3970/fdmp.2010.006.013

Abstract A general model for two-component transport phenomena applicable for both nanofluids and binary solutions is formulated. We investigate a combined long-wave Marangoni and Rayleigh instability of a quiescent state of a binary (nano-) liquid layer with a non-deformable free surface. The layer is heated from below or from above. The concentration gradient is induced due to the Soret effect. A typical behavior of monotonic and oscillatory instability boundaries is examined in the limit of asymptotically small Lewis numbers and poorly conducting boundaries in the two important long-wave domains k~Bi1/2and k~Bi1/4. More >