Jiang Min, Lu Tingting, Zhang Qiang, Chen Ying, Zhou Guangyuan^*

Journal of Renewable Materials, Vol.3, No.2, pp. 120-141, 2015, DOI:10.7569/JRM.2014.634139

Abstract Novel copolyesters were successfully synthesized from terephthalic acid (TPA), 2,5-furandicarboxylic acid (FDCA) and ethylene glycol, 1,3-propanediol, 1,4-butanediol, 1,6-hexanediol and 1,8-octanediol via direct esterifi cation method by using tetrabutyl titanate (TBT) as catalyst. The copolyesters were characterized by nuclear magnetic resonance spectroscopy (¹ H-NMR), gel permeation chromatography (GPC), X-ray diffraction (XRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile tests. The results of GPC showed that all of the copolyesters had high molecular weight, with an average molecular weight (Mw) more than 1×10⁴ g/mol. The results of ¹ H-NMR showed that the copolyesters were random copolymers which… More >

John C. Hoiby¹, Anil N. Netravali^2,*

Journal of Renewable Materials, Vol.3, No.3, pp. 244-258, 2015, DOI:10.7569/JRM.2015.634110

Abstract This article discusses the construction (virtual model) of a fully green cabin using two types of green composites: those that use natural plant-based fibers with soy protein-based resin which have mechanical properties comparable to wood and wood products, and those that use liquid crystalline cellulose fibers with soy proteinbased resin which have properties comparable to high strength steel. Green composites with moderate strength were used to create molded walls and advanced green composites were used to create the load-bearing framework of the cabin. Construction with molded composites and prefabricated framework can greatly simplify traditional wood More >

Mike Lawrence

Journal of Renewable Materials, Vol.3, No.3, pp. 163-174, 2015, DOI:10.7569/JRM.2015.634105

Abstract The relative importance of embodied energy and operational energy on the environmental impact of construction are examined in this article. It highlights the fact that the targets set by the Kyoto Protocol are primarily being met by the reduction of in-use energy, and that the implications of that are that the energy embodied in buildings will increase in signifi cance from its current 17% level to 50% by 2050. The article describes how the use of bio-based renewable materials can make a signifi cant contribution to reducing not only the embodied energy of buildings by More >

Journal of Renewable Materials, Vol.3, No.3, pp. 161-162, 2015, DOI:10.7569/JRM.2015.634113

Abstract This article has no abstract. More >

Philippe Evon^1,2,*, Ika A. Kartika³, Luc Rigal^1,2

Journal of Renewable Materials, Vol.2, No.1, pp. 52-65, 2014, DOI:10.7569/JRM.2013.634131

Abstract The infl uence of thermo-pressing conditions on the mechanical properties of particleboards obtained from Jatropha press cakes was evaluated in this study. Conditions such as molding temperature and press cake oil content were included. All particleboards were cohesive, with proteins and fibers acting respectively as binder and reinforcing fillers. Generally, it was the molding temperature that most affected particleboard mechanical properties. The most resistant boards were obtained using 200°C molding temperature. Glass transition of proteins then occurred during molding, resulting in effective wetting of the fi bers. At this optimal molding temperature, the best compromise between More >

Dinesh Balgude, Anagha Sabnis^*

Journal of Renewable Materials, Vol.2, No.3, pp. 235-245, 2014, DOI:10.7569/JRM.2014.634115

Abstract Renewable resource-based hybrid crosslinker was successfully synthesized via sol-gel technology. The synthesis involved malenization of Cashew Nut Shell Liquid (CNSL) followed by its silane modifi cation and subsequent hydrolysis and condensation with tetraethyl orthosilicate (TEOS). The synthesized crosslinker was characterized by spectroscopic analysis (FT-IR, ¹ H-NMR, ¹³C-NMR and ²⁹Si-NMR) for structural elucidation. The crosslinker was further formulated in a conventional stoving system. Fully-cured coatings were obtained after stoving at 120°C for ½ hr and were then evaluated for physical, mechanical, chemical, optical, accelerated weathering, electrochemical and morphological properties. The incorporation of hybrid crosslinker in a conventional stoving More >

M.C. Lagel¹, A. Pizzi^1,2, S. Giovando³, A. Celzard⁴

Journal of Renewable Materials, Vol.2, No.3, pp. 220-229, 2014, DOI:10.7569/JRM.2014.634113

Abstract With the depletion of fossil resources, tannin extracts can be a natural alternative to some synthetic products. Hydrolysable chestnut tannin extracts have been used to partially replace phenol in PF resins for phenolic rigid foams. Phenol-formaldehyde-chestnut tannin (PFT) phenolic foams were initially made from copolymerized PFT resins of different molar ratio. The PFT foams so prepared were tested for thermal conductivity, these being slightly worse than that of pure PF foams; and for mechanical and water absorption, these two properties being better than those of pure PF foams. Indeed, PF resins represent an important part More >

Richard C. Ferguson, Sharathkumar K. Mendon, James W. Rawlins^*, Shelby F. Thames

Journal of Renewable Materials, Vol.2, No.3, pp. 166-172, 2014, DOI:10.7569/JRM.2013.634133

Abstract Commercial particleboards are currently synthesized by blending wood furnish with formaldehyde-based resins and curing them under a combination of heat and pressure. Particleboards manufactured with urea-formaldehyde resin are known to liberate formaldehyde during their service lives. Formaldehyde’s carcinogenicity has prompted the search for environmentally-friendly resins for wood composite manufacture. Soybean protein-based adhesives have been developed as a renewable and formaldehyde-free replacement for urea-formaldehyde resins. Particleboards processed using the soybean protein adhesive matched or exceeded performance criteria of M-2-grade commercial particleboards when evaluated as per American National Standards Institute (ANSI) specifi cations. More >

Arne Rüdiger^1,2, Peter Hendil-Forssell³, Cecilia Hedfors³, Mats Martinelle³, Stacy Trey^4,5,*, Mats Johansson^1,4

Journal of Renewable Materials, Vol.1, No.2, pp. 124-140, 2013, DOI:10.7569/JRM.2012.634109

Abstract The present study describes the use of an epoxy functional fatty acid, 9,10-epoxy-18-hydroxyoctadecanoic acid (EFA), extracted from birch (Betula pendula) outer bark to produce thermosets. The purifi ed epoxy fatty acid was polymerized by enzyme-catalyzed polycondensation utilizing Candida antarctica lipase B (CalB) to form oligomers with targeted degrees of polymerization (DP) of 3, 6, and 9 and obtained DPs of 2.3, 5.9 and 7.3, respectively. It was determined that it is possible to fi rst enzymatically polymerize and aliphatically endcap the epoxy functional fatty acid resulting in controlled oligomer lengths while also maintaining the epoxy functionality… More >

Andrea Morelli, Dario Puppi, Federica Chiellini^*

Journal of Renewable Materials, Vol.1, No.2, pp. 83-112, 2013, DOI:10.7569/JRM.2012.634106

Abstract Polymers, particularly those susceptible to undergoing biodegradation under physiological environments, can be considered the materials of choice for biomedical applications such as tissue engineering, regenerative medicine, and controlled and targeted drug delivery. The development of these relatively new fi elds of biomedical research represents the driving force towards the exploitation of renewable resources for the obtainment of biobased polymeric biomaterials. This perspective article reports on the biomedical applications of three major categories of biobased polymeric materials obtained from renewable resources, namely, polysaccharides, proteins and polyesters of natural origins. Particular emphasis is given to biobased polymers More >