Jean-Jacques Sinou¹

Structural Durability & Health Monitoring, Vol.3, No.3, pp. 133-164, 2007, DOI:10.3970/sdhm.2007.003.133

Abstract This paper aims to establish a damage identification methodology, called the Frequencies' Ratio Surfaces Intersection method (FRSI-method), for predicting not only the location and depth of the crack but also the crack orientation in a circular cross section beam. Two new criterions %Δ_i^cracked and %ψ_i,j^cracked that consider only the ratio of the natural frequencies of the cracked beam are introduced and discussed in order to detect the crack parameters. In order to avoid worse diagnostic, it is demonstrated that a robust identification of crack location is possible by investigating the emergence of extra antiresonance peaks… More >

S.P.L. Leme¹, M.H. Aliabadi², L.M. Bezerra¹, P.W. Partridge¹

Structural Durability & Health Monitoring, Vol.3, No.3, pp. 121-132, 2007, DOI:10.3970/sdhm.2007.003.121

Abstract The coupled electromechanical behaviour of a thin piezoceramic sensor bonded to a stiffened panel subjected to membrane mechanical loadings is examined. The sensor is characterised by an electrostatic line model bonded to a damaged panel modelled by the dual boundary element method. Numerical results obtained demonstrate that the proposed method is capable of modelling changes in the signal output due to presence of cracks. Also presented is a numerical model for detecting fatigue crack growth in a stiffened panel using piezoceramic sensors. More >

T. Tanaka¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.4, No.4, pp. 251-256, 2007, DOI:10.3970/icces.2007.004.251

Abstract The viscoplastic constitutive relations with kinematic strain hardening-softening model for geomaterials are developed. The constitutive models include strain-rate dependent properties based on the thoery by Duvaut-Lions. The dynamic relaxation method for static problems and the dynamic analysis for earthquake responses are applied to boundary value problems using finite element methods. More >

M.D. de Tullio¹, P. De Palma¹, G. Pascazio¹, M. Napolitano¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.3, No.3, pp. 151-156, 2007, DOI:10.3970/icces.2007.003.151

Abstract This paper provides a numerical method based on the immersed boundary approach for computing compressible viscous flows. The efficency of the method is enhanced by using a flexible local grid refinement technique which is obtained by coarsening a uniformly fine mesh far from high-gradient flow regions, such as boundary layers and shocks. More >

Oleg Vorobiev¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.2, No.1, pp. 1-6, 2007, DOI:10.3970/icces.2007.002.001

Abstract Common-plane (CP) algorithm is widely used in Discrete Element Method (DEM) to model contact forces between interacting particles or blocks. A new simple contact detection algorithm is proposed to model contacts in FE/FD methods which is similar to the CP algorithm. The CP is defined as a plane separating interacting faces of FE/FD mesh instead of blocks or particles in the original CP method. The method does not require iterations. It is very robust and easy to implement both in 2D and 3D case. More >

C. Soutis¹, K. Diamanti¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.1, No.2, pp. 49-54, 2007, DOI:10.3970/icces.2007.001.049

Abstract A cost and time effective inspection strategy for in-service health monitoring of composites is demonstrated using the fundamental anti-symmetric A0 Lamb mode at frequencies of 15-20 kHz. In principle, this method involves analysis of the transmitted and/or reflected wave after interacting with the test-piece boundaries or discontinuities (defects). In the present work, the applicability of the technique to composite sandwich structures is explored. More >

Shamsh Tabrez, Mira Mitra, S. Gopalakrishnan¹

CMES-Computer Modeling in Engineering & Sciences, Vol.22, No.1, pp. 77-90, 2007, DOI:10.3970/cmes.2007.022.077

Abstract In this paper, wave propagation is studied in degraded composite beam due to moisture absorption. The obtained wave responses are then used for diagnosis of the degraded zone. Moisture absorption causes an irreversible hygrothermal deterioration of the material. The change in temperature and moisture absorption changes the mechanical properties. Thus this affects the structure in dimensional stability as well as material degradation due to reduction in mechanical properties. Here, the composite beam is modeled as Timoshenko beam using wavelet based spectral finite element (WSFE) method. The WSFE technique is especially tailored for simulation of wave More >

N. Osawa¹, K. Hashimoto¹, J. Sawamura¹, J. Kikuchi², Y. Deguchi², T. Yamaura²

CMES-Computer Modeling in Engineering & Sciences, Vol.20, No.1, pp. 43-54, 2007, DOI:10.3970/cmes.2007.020.043

Abstract A new hypothesis regarding heat transmission during line heating is proposed. It states that the distribution of the temperature of the gas adjacent to the plate, T_G, and the overall local heat transfer coefficient, α, depend only on the distance from the torch. An identification technique for T_G and α is developed. The validity of the employed hypothesis and the proposed technique is demonstrated by comparing the measured and identified T_G during a spot heating test. The plate temperature calculated by direct heat conduction analysis closely approximates the one measured for the spot and line heating tests, More >

M. Heshmatzadeh, G. E. Bridges¹

CMES-Computer Modeling in Engineering & Sciences, Vol.18, No.1, pp. 45-58, 2007, DOI:10.3970/cmes.2007.018.045

Abstract Cell Method, a Finite Formulation technique, is compared in detail with the Finite Element Method (FEM), a differential-based numerical technique. In the finite formulation technique, Poisson's equation is described starting from a topological foundation. The final set of algebraic equations resulting from the two approaches are compared in matrix form. The equivalence of the coefficient matrices is proven for a Voronoi dual mesh and linear shape functions in the FEM. The difference between the source (charge) vectors in the two approaches is described. It is shown that the use of linear shape functions in the More >

Kanchi Venkatesulu Reddy¹, Ranjan Ganguli²

CMC-Computers, Materials & Continua, Vol.5, No.2, pp. 79-98, 2007, DOI:10.3970/cmc.2007.005.079

Abstract This paper investigates the effect of damage on beams with fixed boundary conditions using Fourier analysis of the mode shapes in spatial domain. A finite element model is used to obtain the mode shapes of a damaged fixed-fixed beam. Then the damaged beams are studied using a spatial Fourier analysis. This approach contrasts with the typical time domain application of Fourier analysis for vibration problems. It is found that damage causes considerable change in the Fourier coefficients of the mode shapes. The Fourier coefficients, especially the higher harmonics, are found to be sensitive to both More >