Tao Zhang^1,2, Leiting Dong^2,3, Abdullah Alotaibi⁴, Satya N. Atluri^2,5

CMES-Computer Modeling in Engineering & Sciences, Vol.94, No.1, pp. 1-28, 2013, DOI:10.3970/cmes.2013.094.001

Abstract In this paper, a novel Meshless Local Petrov-Galerkin (MLPG) Mixed Collocation Method is developed for solving the inverse Cauchy problem of linear elasticity, wherein both the tractions as well as displacements are prescribed/measured at a small portion of the boundary of an elastic body. The elastic body may be isotropic/anisotropic and simply connected or multiply-connected. In the MLPG mixed collocation method, the same meshless basis function is used to interpolate both the displacement as well as the stress fields. The nodal stresses are expressed in terms of nodal displacements by enforcing the constitutive relation between… More >

Hsien-Chie Cheng^1,2, Chien-Hao Ma¹, Ching-Feng Yu³, Su-Tsai Lu⁴, Wen-Hwa Chen^2,3

CMC-Computers, Materials & Continua, Vol.38, No.3, pp. 129-154, 2013, DOI:10.3970/cmc.2013.038.129

Abstract User experiences for electronic devices with high portability and flexibility, good intuitive human interfaces and low cost have driven the development of semiconductor technology toward flexible electronics and display. In this study proposes, an advanced flexible interconnect technology is proposed for flexible electronics, in which an ultra-thin IC chip having a great number of micro-bumps is bonded onto a very thin flex substrate using an epoxy-based anisotropic conductive film (ACF) to form fine-pitch and reliable interconnects or joints (herein termed ACF-typed thin-flip-chip-on-flex (TFCOF) technology). The electrical and thermal -mechanical performances of the micro-joints are the… More >

Chyanbin Hwu¹, Tai-Liang Kuo²

CMC-Computers, Materials & Continua, Vol.36, No.2, pp. 135-153, 2013, DOI:10.3970/cmc.2013.036.135

Abstract The problems of the interface corners between two dissimilar anisotropic viscoelastic materials are studied in this paper. Through the use of the well-known correspondence principle between linear elasticity and linear viscoelasticity, fracture parameters in the Laplace domain can be obtained from the path-independent H-integral for the corresponding problems of anisotropic linear elastic materials. Further application of the correspondence relations for fracture parameters proposed in our recent study then leads us the solutions of fracture parameters in the time domain. To show the applicability and accuracy of the proposed method, several different kinds of numerical examples More >

M. Chatiri¹, A. Matzenmiller²

CMC-Computers, Materials & Continua, Vol.35, No.3, pp. 255-283, 2013, DOI:10.3970/cmc.2013.035.255

Abstract This article presents a three dimensional constitutive model for anisotropic damage to describe the elastic-brittle behavior of unidirectional fibrereinforced laminated composites. The primary objective of the article focuses on the three dimensional relationship between damage of the material and the effective elastic properties for the purpose of stress analysis of composite structures, in extension to the two dimensional model in Matzenmiller, Lubliner and Taylor (1995). A homogenized continuum is adopted for the constitutive theory of anisotropic damage and elasticity. Damage initiation criteria are based on Puck failure criterion for first ply failure and progressive micro More >

Deli Gao¹, Zhen Dong¹, Hui Zhang¹

CMES-Computer Modeling in Engineering & Sciences, Vol.89, No.2, pp. 111-122, 2012, DOI:10.3970/cmes.2012.089.111

Abstract The bottom hole pendulum assembly is a type of bottom hole assembly (BHA) for controlling the hole deviation, and has been widely used in drilling engineering. Generally, the ability of the drill bit to penetrate laterally, is different from its ability to penetrate axially, so that the drill bit has an anisotropy which affects the hole-deviation-control characteristics of the BHA. The tilt angle and the side force of the drill bit are obtained by a BHA analysis based on the method of weighted residuals. Thus, the effective drilling force can be determined using the rock-bit… More >

W.W. Zhang¹, Y.F. Nie¹, Y.Q. Li¹

CMES-Computer Modeling in Engineering & Sciences, Vol.88, No.6, pp. 507-530, 2012, DOI:10.3970/cmes.2012.088.507

Abstract A new algorithm for anisotropic triangular meshes generation in two dimension is presented. The inputs to the algorithm are the boundary geometry information and a metric tensor that specifies the desired element size and shape. The initial nodes are firstly distributed according to the above mentioned geometrical information, after bubble simulation, the optimized nodes set that meets the requirements of the metric tensor is obtained quickly. Then taking full advantage of the nodes set and the adjacency lists information provided by the process of node placement, a handful of non-satellite nodes are removed from the… More >

Taffetani M.¹, Bertarelli E.^1,2, Gottardi R.^3,4, Raiteri R.⁵, Vena P.^1,2

CMES-Computer Modeling in Engineering & Sciences, Vol.87, No.5, pp. 433-460, 2012, DOI:10.3970/cmes.2012.087.433

Abstract Dynamic nanoindentation is a novel nanomechanical testing that is being increasingly used to characterize the frequency response of viscoelastic materials and of soft hydrated biological tissues at the micrometric and nanometric length scales. This technique is able to provide more information than those obtained by simple indentation; however, its interpretation is still an open issue for complex materials such as the case of anisotropic biological tissues that generally have a high water content. This work presents a numerical model to characterize the frequency response of poro-elastic tissues subjected to harmonic indentation loading with particular regard… More >

L. Rodríguez-Tembleque¹, R. Abascal¹, M.H. Aliabadi²

CMES-Computer Modeling in Engineering & Sciences, Vol.87, No.2, pp. 127-156, 2012, DOI:10.3970/cmes.2012.087.127

Abstract A boundary element based formulation is proposed to simulate 3D fretting wear under gross-sliding and partial slip conditions, assuming anisotropic friction and wear laws. Contact problem is based on an Augmented Lagrangian formulation, and restrictions fulfilment is established by a set of projection functions. The boundary element method reveals to be a very suitable numerical method for this kind of problems, where the degrees of freedom involved are those on the solids surfaces, and a very good approximation on contact tractions is obtained with a low number of elements. The present boundary element anisotropic fretting More >

M.R. Hematiyan^1,2, A. Khosravifard¹, Y.C. Shiah³, C.L. Tan⁴

CMES-Computer Modeling in Engineering & Sciences, Vol.87, No.1, pp. 55-76, 2012, DOI:10.3970/cmes.2012.087.055

Abstract An inverse technique, based on the boundary element method (BEM) and elastostatic experiments for identification of elastic constants of orthotropic and general anisotropic 2D bodies is presented. Displacement measurements at several points on the boundary of the body, obtained by a few known load cases are used in the inverse analysis to find the unknown elastic constants of the body. Using data from more than one elastostatic experiment results in a more accurate and stable solution for the identification problem. In the inverse analysis, sensitivities of displacements of only boundary points with respect to the More >

Y.C. Shiah¹, C. L. Tan², C.Y. Wang¹

CMES-Computer Modeling in Engineering & Sciences, Vol.87, No.1, pp. 1-22, 2012, DOI:10.3970/cmes.2012.087.001

Abstract The fundamental solution, or Green's function, for 3D anisotropic elastostatics as derived by Ting and Lee (1997) [Q.J. Mech. Appl. Math.; 50: 407-426] is one that is fully explicit and algebraic in form. It has, however, only been utilized in boundary element method (BEM) formulations quite recently even though it is relatively straightforward and direct to implement. This Green's function and its derivatives are necessary items in this numerical analysis technique. By virtue of the periodic nature of the angles when it is expressed in the spherical coordinate system, the present authors have very recently… More >