N. Shishido, T. Ikeda, N. Miyazaki

CMES-Computer Modeling in Engineering & Sciences, Vol.35, No.1, pp. 1-20, 2008, DOI:10.3970/cmes.2008.035.001

Abstract We propose an image correction method that will accurately measure full-field displacement in a microstructure using the digital image correlation method (DICM); the proposed method is suitable for use with laser-scanned images. Laser scanning microscopes have higher spatial resolution and deeper depth of field than optical microscopes, but errors in laser scanning position (time-dependent distortion) affect the accuracy of the DICM. The proposed image correction method involves the removal of both time-dependant and time-independent distortions. Experimental results using images of prescribed rigid-body motions demonstrate that the proposed correction method is capable of identifying and removing… More >

Shih-Kai Chien¹, Tzu-Hsiang Yen¹, Yue-Tzu Yang¹, Chao-Kuang Chen^1,2

CMES-Computer Modeling in Engineering & Sciences, Vol.29, No.3, pp. 163-174, 2008, DOI:10.3970/cmes.2008.029.163

Abstract Conventional proton exchange membrane fuel cells (PEMFCs) have a straight gas flow serpentine channel, and hence the reactant gases are transferred to the catalyst layers as a result of diffusion alone. Since the diffusion process is inherently slow, the electrical performance of such PEMFCs is inevitably limited. In an attempt to improve the PEMFC performance, this study replaces the straight channel with containing different type of obstacles and conducts a series of lattice Boltzmann method simulations to investigate the flow field phenomena induced in a viscous liquid as it flows along the serpentine channel at… More >

H.M. Lee¹, H.S. Park^1,2

CMES-Computer Modeling in Engineering & Sciences, Vol.29, No.1, pp. 29-44, 2008, DOI:10.3970/cmes.2008.029.029

Abstract This paper presents a computational model to estimate deformed shapes of beam structures using 3D coordinate information from terrestrial laser scanning (TLS). The model is composed of five components: 1) formulation of polynomial shape function, 2) application of boundary condition, 3) inducement of compatibility condition, 4) application of the least square method and 5) evaluation of error vector and determination of reasonable polynomial shape function. In the proposed model, the optimal degree of polynomial function is selected based on the complexity of beam structures, instead of using a specific degree of polynomial function. The chosen More >

C. Moulinec¹, R. Issa², J.-C. Marongiu³, D. Violeau⁴

CMES-Computer Modeling in Engineering & Sciences, Vol.25, No.3, pp. 133-148, 2008, DOI:10.3970/cmes.2008.025.133

Abstract The gridless Smoothed Particle Hydrodynamics (SPH) numerical method is preferably used in Computational Fluid Dynamics (CFD) to simulate complex flows with one or several convoluted free surfaces. This type of flows requires distorted meshes with classical Eulerian mesh-based methods or very fine meshes with Volume of Fluid method. Few 3-D SPH simulations have been carried out to our knowlegde so far, mainly due to prohibitive computational investment since the number of particles required in 3-D is usually too large to be handled by a single processor. In this paper, a parallel 3-D SPH code is More >

Nicolas Ali Libre^1,2, Arezoo Emdadi², Edward J. Kansa^3,4, Mohammad Rahimian², Mohammad Shekarchi²

CMES-Computer Modeling in Engineering & Sciences, Vol.24, No.1, pp. 61-80, 2008, DOI:10.3970/cmes.2008.024.061

Abstract The numerical solution of partial differential equations (PDEs) with Neumann boundary conditions (BCs) resulted from strong form collocation scheme are typically much poorer in accuracy compared to those with pure Dirichlet BCs. In this paper, we show numerically that the reason of the reduced accuracy is that Neumann BC requires the approximation of the spatial derivatives at Neumann boundaries which are significantly less accurate than approximation of main function. Therefore, we utilize boundary treatment schemes that based upon increasing the accuracy of spatial derivatives at boundaries. Increased accuracy of the spatial derivative approximation can be… More >

G. Accary¹, S. Meradji², D. Morvan², D. Fougère²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.4, pp. 263-270, 2008, DOI:10.3970/fdmp.2008.004.263

Abstract In the literature, only few references have dealt with mixed-convection flows in the low Mach number approximation. For this reason, in the present study we propose to extend the standard 3D benchmark for mixed convection in a rectangular channel heated from below (Medale and Nicolas, 2005) to the case of large temperature variations (for which the Boussinesq approximation is no longer valid). The Navier-Stokes equations, obtained under the assumption of a low Mach number flow, are solved using a finite volume method. The results, corresponding to the steady-state case of the benchmark, lead to the More >

BIOCELL, Vol.31, Suppl.S, pp. 149-193, 2007

Abstract This article has no abstract. More >

BIOCELL, Vol.31, Suppl.S, pp. 113-148, 2007

Abstract This article has no abstract. More >

BIOCELL, Vol.31, Suppl.S, pp. 75-112, 2007

Abstract This article has no abstract. More >

BIOCELL, Vol.31, Suppl.S, pp. 247-317, 2007

Abstract This article has no abstract. More >