Thomas Boeck¹, Alexander Nepomnyashchy^2,3, Ilya Simanovskii²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.1, pp. 11-20, 2008, DOI:10.3970/fdmp.2008.004.011

Abstract Anticonvection in a two-layer system of mercury and water is studied using three-dimensional direct numerical simulations with a Fourier-Chebyshev spectral method. The two fluid layers have equal thicknesses and are uniformly heated from above. Interface deformations and surface tension gradients are neglected. The quiescent state is replaced by steady hexagons upon increasing the heating from above. We investigate the destabilization of this primary convective pattern in a small and in a large computational domain upon increasing the temperature difference across the two fluid layers. For the large domain the convection cells become disordered at about More >

G.Pétré¹, K.Tshinyama, A. Azouni², S. Van Vaerenbergh¹

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.1, pp. 1-10, 2008, DOI:10.3970/fdmp.2008.004.001

Abstract This study illustrates a relevant and practical method to determine the effective surface tension gradient in a layer subjected to a lateral temperature difference. In general, this can be hardly performed in situ without perturbing the flow. For this reason we rely on an indirect determination approach. A simple model is developed that relates the surface tension gradient to other quantities that can be measured without introducing significant disturbances in the system. Measurements of these quantities are performed in a set-up where the flow corresponds with a good approximation to a one-dimensional model. A previously used More >

A. A. Nepomnyashchy^1,2, I. B. Simanovskii¹

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.3, pp. 185-198, 2008, DOI:10.3970/fdmp.2008.004.185

Abstract The development of instabilities under the joint action of the van der Waals forces and Marangoni stresses in a two-layer film on a heated or cooled substrate is considered. It is found that heating from below leads to the acceleration of the decomposition, decrease of the characteristic lateral size of structures, and the increase of the droplets heights. Heating from above leads to slowing down the instability rate and eventually to a complete suppression of the instability. More >

Md. Tofiqul Islam¹, Sumon Saha², Md. Arif Hasan Mamun³, Mohammad Ali⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 125-138, 2008, DOI:10.3970/fdmp.2008.004.125

Abstract A numerical study has been performed on mixed convection inside an open cavity on the bottom of a channel. One of the three walls of the cavity experiences a uniform heat flux while the other walls and the top of the channel are adiabatic. Three different cases are considered by applying uniform heat flux on (a) the inflow side (assisting forced flow); (b) the outflow side (opposing forced flow); (c) the bottom horizontal surface (transverse flow). The Galerkin weighted residual method of finite element formulation is used to discretize the governing equations. For mixed convection,… More >

S. Sabbaghi¹, M. Shariaty-Niassar², Sh. Ayatollahi¹, A. Jahanmiri¹

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 113-124, 2008, DOI:10.3970/fdmp.2008.004.113

Abstract In this study, the Onset of Asphaltene Precipitation is predicted by a modified Virial equation of state. The bases of quantum mechanics and statistical thermodynamics are used to evaluate the potential energy and intermolecular forces related to asphaltene molecules. The Virial equation of state is modified using group-contribution-methods for asphaltenes, which are assumed to be polymeric-like compounds consisting of aggregates of monodisperse asphaltene monomers. It is shown how the modified Virial equation of state with the Peneloux correction leads to estimate the molar volume and solubility parameter. These parameters are also compared successfully with results More >

Sayavur I. Bakhtiyarov¹, Dennis A. Siginer²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 99-112, 2008, DOI:10.3970/fdmp.2008.004.099

Abstract Levitation of liquid bodies against gravity is a contactless confinement process appropriate for manufacturing very pure materials. A variety of levitation techniques have been developed over the last few decades, such as aerodynamic, acoustic, electrostatic, microwave, and electromagnetic levitations. More recently, a new generation of novel techniques, essentially combinations of the established primary techniques, has been successfully introduced. Examples are acoustic-electric, aerodynamic-acoustic and acoustic-electromagnetic. The purpose of this series of papers in three parts, Bakhtiyarov and Siginer (2007a,b), is to review the advances in electromagnetic levitation (EML) since its introduction as a containerless melting technique, More >

Viveca Wallqvist¹, Per M. Claesson², Agne Swerin¹, Patrick A. C. Gane^3,4,3, Joachim Schoelkopf³

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 85-98, 2008, DOI:10.3970/fdmp.2008.004.085

Abstract It has been shown that talc powder can be compacted into tablets with a preferred orientation of the platelets. The tablets can be obtained with different controlled porosity depending on pressing methods and applied pressure. The tablets can be obtained with or without additives, which may, in turn, be adsorbed. The orientation of the high aspect ratio platy talc, the surface chemistry imparted by the additives and the transported fluid influence the imbibition and permeation rates. Non-polar hexadecane displays a higher imbibition and permeability than water for all particulate orientations during short timescale absorption, likely… More >

Adeline Tchikango Siagam¹, Gunther Brenner¹, Peter Giese², Volker Wesling²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 77-84, 2008, DOI:10.3970/fdmp.2008.004.077

Abstract The PTA (''Plasma-Transferred-Arc'') is a widespread variant of plasma powder processes to manufacture coatings against corrosion or abrasion. For the optimization of this technique, an explanation of the processes which lead to a maximal deposition performance (i.e. maximal quantity of powder converted per time) is required. Especially the gas and particle flow in the region between the burner nozzle and the work piece is of interest. In the present study, flow simulations (Computational Fluid Dynamics, CFD) have been done in order to investigate the determining factors for the dimensioning of the processes. Additionally, velocity measurements… More >

H. Payer¹, T. Haschke¹, R. Reichardt¹, G. Li², K. Graf^2,3, W. Wiechert^1,3

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.2, pp. 61-76, 2008, DOI:10.3970/fdmp.2008.004.061

Abstract Microstructured surfaces are of steadily increasing importance in a large variety of technological applications. For the purpose of quality assurance, e.g. during variation studies of experimental parameters or for comparison with results from simulations, the surface geometry must be precisely measured and described in terms of geometric parameters. An analysis tool for regularly structured surfaces is presented that performs a highly automated evaluation of surface scanning data and derives geometric quality control parameters. To demonstrate the power of the analysis tool it is exemplarily applied for the investigation of microcraters emerging after the evaporation of… More >

A. Ovcharova¹, N.Stankous²

FDMP-Fluid Dynamics & Materials Processing, Vol.3, No.4, pp. 349-356, 2007, DOI:10.3970/fdmp.2007.003.349

Abstract We consider a deformation of a thin film which is hanging between two solid flat walls under thermal load action. A two-dimensional model is applied to describe the motion of thin layers of viscous nonisothermal liquid under microgravity conditions. The model is based on the Navier-Stokes equations. A numerical analysis of the influence of thermal loads on the deformation and break of freely hanging thin films has been carried out. The mutual influence of capillary and thermo-capillary forces on thin film free surface position has been shown. The results of model problem solutions are presented. More >