G. Boopathy^1,2,*, K. Gurusami¹, M. Chinnapandian³, K. R. Vijayakumar⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.2, pp. 223-232, 2022, DOI:10.32604/fdmp.2022.018225 - 16 December 2021

Abstract In this research study, the mechanical properties of several Polymer matrix composites are investigated. These composites are multi-phase materials in which reinforcing materials are properly mixed with a polymer matrix. More precisely, Nylon 6 reinforced with 5, 15 and 25 wt. % of silicon carbide (SiC) and Nylon 6 reinforced with 5, 15 and 25 wt. % of boron carbide (B₄C), prepared by means of an injection moulding process at three different injection pressures are considered. Specific attention is paid to the tensile and impact strength of these composites. The Taguchi technique is used to optimize the process More >

S.R. MANE^1,2, E. K. PATHAN³, G. PATIL⁴, S. G. TUPE⁵, V. GHORMADE⁴, B. P. CHAUDHARI^1,2, M.V. DESHPANDE^5,*

Journal of Polymer Materials, Vol.38, No.3-4, pp. 219-230, 2021, DOI:10.32381/JPM.2021.38.3-4.4

Abstract A dimorphic fungus Benjaminiella poitrasii contains high chitin/chitosan (35% of the cell wall) in the mycelial (M) form than its yeast (Y) form (20% of the cell wall). However, the relative proportion of chitosan is more in yeast form cells (chitosan: chitin ratio, 6:1) than mycelial cells (chitosan: chitin ratio, 3:1). Using the Taguchi design of experimental (DOE) approach, interactions among eight different parameters showed that carbon source (starch, 10 g/L), incubation time (48 h), inoculum (M and Y mixed 10%), yeast extract (6 g/L) and peptone (10 g/L), were optimum for maximum biomass production.… More >

Manar B. AL-Hajji^1,*, Nabeel Abu Shaban², Shahnaz Al Khalil², Ayat Al-Jarrah³

Energy Engineering, Vol.118, No.5, pp. 1425-1438, 2021, DOI:10.32604/EE.2021.016413 - 16 July 2021

Abstract Solar energy is regarded as one of the promising renewable energy sources in the world.The main aim of this study is to use the Taguchi-Grey relational grade analysis to optimize the performance of two Solar Air Heaters (SAHs). A typical Grey–Taguchi method was applied. The Orthogonal Array, Signal-to-Noise ratio, Grey Relational Grade, and Analysis of Variance were employed to investigate the performance characteristics of SAH. Experimental observations were made in agreement with Jordanian climate 32°00′ N latitude and 36°00′ E longitude with a solar intensity of 500 W\m². The operating factors selected for optimization are the… More >

Weiwei Zhang, Linghong Tang^*

Frontiers in Heat and Mass Transfer, Vol.15, pp. 1-7, 2020, DOI:10.5098/hmt.15.9

Abstract Air-side thermal and hydraulic performance of the finned flat-tube heat exchanger with single row is experimentally investigated. The correlations of the thermal and hydraulic performance are developed based on the experimental data. The effects of various fin geometrical parameters on the thermal and hydraulic performance are investigated by a numerical method, and the influence of various parameters is analyzed in detail. Results show that heat transfer performance and pressure drop decrease with the increasing fin pitch, and heat transfer performance increases with the increase of fin length and fin height accompanying with the increase of More >

Mohammed Yunus^*, Mohammad S. Alsoufi

Frontiers in Heat and Mass Transfer, Vol.12, pp. 1-8, 2019, DOI:10.5098/hmt.12.11

Abstract Swift cooling systems, improved microprocessor chips, processors’ performance and power usage have increased production of an enormous amount of heat and high operating temperatures due to excess heat flux density in the field of microelectronics. A rapid cooling of electronic circuits and heat dissipation for the same size of pipe with the present technology as nano size circuits critically generate high heat flux beyond 100 W/cm2 is currently the challenging task with which we are presented. Cooling in the form of heat transfer should be managed using both thermal conductivity (evaporation) and phase transition (condensation)… More >

Ridha Djebali¹, Mohsen Toujani², Bernard Pateyron³

CMC-Computers, Materials & Continua, Vol.37, No.3, pp. 147-160, 2013, DOI:10.3970/cmc.2013.037.147

Abstract In this paper a study of the atmospheric plasma spraying process was conducted. The Jets&Poudres code was used to solve the partial differential equations for the conservation of mass, momentum and energy involved in the problem together with the K-e turbulent model. The Taguchi technique was used to study the influence of processing factors on droplet impact properties obtained on dense zirconia (ZrO₂) under H₂Ar75% plasma gas that allow optimal functioning condition. The test of the operating parameters for the studied ranges showed that the "thermal power" factor plays a key role on the state of sprayed More >