Juan Yan¹, Wenchao Li¹, Xianfang Zhang¹, Shisheng Liu^2,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.028927

Abstract In this study, intelligent, pH-responsive colorimetric films were prepared by encapsulating anthocyanins in nanocomplexes prepared from glutenin and carboxymethyl chitosan. These nanocomplexes were added to a corn starch matrix and used in the freshness monitoring of chilled pork. The effects of anthocyanin-loaded nanocomplexes on the physical, structural, and functional characteristics of the films were investigated. The addition of anthocyanin-loaded nanocomplexes increased the tensile strength, elongation at break, hydrophobicity, and light transmittance of the films while decreasing their water vapor permeability. This is because new hydrogen bonds are formed between the film components, resulting in a more homogeneous and dense structure.… More >

Jinxing Wang^1,2,3, Yingjie Yang^1,2,3, Xiaolin Yang^1,2,3, Huazhe Jiao^1,2,3,4,*, Qi Wang^1,2,3, Liuhua Yang^1,2,3, Jianxin Yu^1,2,3, Fengbin Chen^1,2,3

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.027512

Abstract In order to improve the comprehensive utilization rate of high fines sand (HFS) produced by the mine, full solid waste shotcrete (HFS-BFRS) was prepared with HFS as fine aggregate in cooperation with basalt fiber (BF). The strength growth characteristics of HFS-BFRS were analyzed. And the fitting equation of compressive strength growth characteristics of HFS-BFRS under the synergistic effect of multiple factors was given. And based on the orthogonal experimental method, the effects on the compressive strength, splitting tensile strength and flexural strength of HFS-BFRS under the action of different levels of influencing factors were investigated. The effect of three factors… More >

Aida Haryati Jamadi¹, Nadlene Razali^1,3,*, Sivakumar Dhar Malingam^1,3, Mastura Mohammad Taha^2,3

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.028280

Abstract Natural fibre as a reinforcing agent has been widely used in many industrial applications. Nevertheless, several factors need to be considered, such as the size and weight percentage of the fibre used in binding. Using fused deposition modelling (FDM), this factor was investigated by varying the size of natural fibre as the responding variable with a fixed weight percentage of kenaf fibre. The process of modifying the natural fibre in terms of size might increase the dispersion of kenaf fibre in the polymer matrix and increase the adhesion bonding between the fibre and matrix of composites, subsequently improving the interfacial… More >

Wenqi Zhao¹, Wenbin Sun^1,2,3,*, Zhenbo Cao¹, Jianbang Hao¹

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.026409

Abstract Mine grouting reinforcement and water plugging projects often require large amounts of grouting materials. To reduce the carbon emission of grouting material production, improve the utilization of solid waste from mining enterprises, and meet the needs of mine reinforcement and seepage control, a double-liquid grouting material containing a high admixture of coal gangue powder/bottom ash geopolymer was studied. The setting time, fluidity, bleeding rate, and mechanical properties of grouting materials were studied through laboratory tests, and SEM analyzed the microstructure of the materials. The results show that the total mixture of calcined gangue does not exceed 60%. And the proportion… More >

Danyang Shao¹, Xiaojia Wang^1,*, Delu Chen¹, Fengxia An^1,2

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.029220

Abstract Methanation is an effective way to efficiently utilize product gas generated from the pyrolysis and gasification of organic solid wastes. To deeply study the heat transfer and mass transfer mechanisms in the reactor, a successful three-dimensional comprehensive model has been established. Multiphase flow behavior and heat transfer mechanisms were investigated under reference working conditions. Temperature is determined by the heat release of the reaction and the heat transfer of the gas-solid flow. The maximum temperature can reach 951 K where the catalyst gathers. In the simulation, changes in the gas inlet velocity and catalyst flow rate were made to explore… More >

Chengxiang Li, Yue Wu, Chunhui Zhang^*, Yao Liu, Qixuan Lin, Junli Ren^*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.026908

Abstract Hemicellulose and lignin are not reasonably utilized during the dissolved pulp preparation process. This work aimed to propose a process for the co-production of dissolving pulp, furfural, and lignin from eucalyptus. High-grade dissolving pulp was prepared from eucalyptus using a combination of extremely low acid (ELA) pretreatment, Kraft cooking, and elementary chlorine-free (ECF) bleaching. The obtained pre-hydrolysate was catalytic conversion into furfural in a biphasic system, and lignin during Kraft cooking and ECF was recovered. The process condition was discussed as well as the mass flow direction. The results showed that ELA pretreatment could effectively remove 80.1% hemicellulose. Compared with… More >

Hui Zheng^1,2, Xiaohan Chen², Li Li², Dawei Qi¹, Jiale Wang¹, Jiaying Lou^1,*, Wenjun Wang^1,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.027748

Abstract The issue of plastic pollution has attracted widespread social attention. Gelatin is valued as a degradable bio-based material, especially as an edible active packaging material. However, the commonly used solution-casting filmforming technology limits the mass production of gelatin films. In order to improve the production efficiency and enhance the commercial value of gelatin films, in this study, fish gelatin (FG) particles were successfully blended with essential oils (EOs) to prepare active films by melt extrusion technique, a common method for commercial plastics, and applied to bread preservation. FG and EOs showed good compatibility with each other. The elongation at break… More >

Jianping Deng¹, Qianqian Zhang¹, Yuling Lan¹, Lingcong Luo¹, Zimin Dai¹, Zhonghang Lin¹, Zhixin Lu¹, Jiancheng Yuan¹, Yiqi Fu¹, Lu Luo^2,*, Weigang Zhao^1,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.027163

Abstract The development and utilization of biomass and agroforestry processing byproducts for high-value applications have been an important topic in the field of renewable materials research. Based on this, a two-step microwave hydrothermal pre-carbonization and KOH activation method was proposed to synthesize tannin-based activated carbons with a high specific surface area, hierarchical pore structure, and good electrochemical performance. The microstructure, texture properties, and physicochemical characteristics were investigated. The results show that the prepared tannin-based activated carbons presented a hierarchical pore structure (micro- and mesopores) with a specific surface area as high as 997.46 m³ g⁻¹ . The electrochemical analysis shows that… More >

Bengang Zhang^1,*, Antonio Pizzi^2,*, Mathieu Petrissans¹, Anelie Petrissans¹, Baptiste Colin¹

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.028888

Abstract Melamine-dialdehyde starch resins used for wood surface finishes have been developed. The reaction of melamine with dialdehyde starch has been shown to occur by FTIR and MALDI ToF spectrometry, with several oligomer species due to the reaction of the two materials being identified, and the resin thermal stability was studied by thermogravimetric analysis. The resins were prepared by two different procedures when it was realized that dialdehyde starch is sensitive to too high a temperature for prolonged times. The melamine-dialdehyde starch resins were applied on particleboard supports as a direct liquid surface finish and a resin-impregnated paper. The surface finishes… More >

Mahdi Hosseini^1,2,*, Bingyu Jian^1,2, Jian Zhang³, Haitao Li^1,2,*, Rodolfo Lorenzo⁴, Ahmad Hosseini⁵, Pritam Ghosh⁵, Feng Shen⁶, Dong Yang^1,2, Ziang Wang^1,2

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2023.028164

Abstract The safety of civilian and military infrastructure is a concern due to an increase in explosive risks, which has led to a demand for high-strength civil infrastructure with improved energy absorption capacity. In this study, a Finite Element (FE) numerical model was developed to determine the effect of hybrid Fibre Reinforced Polymer (FRP) as a strengthening material on full-scale Reinforced Concrete (RC) slabs. The reinforcing materials under consideration were Carbon (CFRP) and Glass (GFRP) fibres, which were subjected to blast loads to determine the structural response. A laminated composite fabric material model was utilized to model the failure of composite,… More >