Dianen Liang¹, Zhenhao Ding¹, Qilin Yan¹, Redžo Hasanagić², Leila Fathi³, Zi Yang¹, Longhao Li¹, Jianbo Wang¹, Houhua Luo¹, Qian Wang¹, Demiao Chu^1,*

Journal of Renewable Materials, DOI:10.32604/jrm.2022.023214

Abstract This study aims to improve the value of fast-growing wood and extend the heat-treated wood utilization using inorganic calcium carbonate (CaCO₃) crystals via an in-situ synthesis method. CaCl₂ and Na₂CO₃ solutions with a concentration ratio of 1:1 were successively introduced into the thermally modified poplar wood obtained by steam heat treatment (HT) at 200°C for 1.5 and 3 h, resulting in the in-situ synthesis of CaCO₃ crystals inside the heat-treated wood. The filling effect was best at the concentration of 1.2 mol/L. CaCO₃ was uniformly distributed in the cell cavities of the heat-treated wood, and some of the… More >

Nurul Hanan Taharuddin¹, Ridhwan Jumaidin^2,*, Muhd Ridzuan Mansor¹, Fahmi Asyadi Md Yusof³, Roziela Hanim Alamjuri^4,*

Journal of Renewable Materials, DOI:10.32604/jrm.2022.021528

Abstract The strict environmental regulations to overcome the drawbacks of consumption and disposal of non-renewable synthetic materials have motivated this investigation. The physical, chemical, morphological, and thermal properties of Hylocereus Polyrhizus peel (HPP) powder obtained from the raw materials were examined in this study. The physical properties analyzes of Hylocereus Polyrhizus peel (HPP) powder discovered that the moisture content, density, and water holding capacity were 9.70%, 0.45 g/cm3 , and 98.60%, respectively. Meanwhile, the chemical composition analysis of Hylocereus Polyrhizus peel (HPP) powder revealed that the powder was significantly high in cellulose contents (34.35%) from other bio-peel wastes. The… More >

Sumari Sumari^*, Mega Murti, Aman Santoso, Muhammad Roy Asrori

Journal of Renewable Materials, DOI:10.32604/jrm.2022.022995

Abstract Kapok seed oil is an environmentally friendly biodiesel feedstock. The problem of the best catalyst for transesterification of Kapok seed oil still continues today. The research developed a base-heterogeneous catalyst with the effect of ultrasonic waves during transesterification. So, the study aims: (1) to determine the type of natural zeolite used, (2) to determine the characteristics of the synthesized CaO:BaO/ANZ catalyst, and (3) to determine the effectiveness of the CaO:BaO/ANZ catalyst in the biodiesel production process through sono-transesterification of kapok seed oil. The research stages consisted of: (1) activation of natural zeolite and its characterization,… More >

Yueqiang Yu¹, Tingang Ma¹, Suling Wang^1,*, Minzheng Jiang¹, Yanling Guo^2,3, Ting Jiang^1,*, Shuaiqi Huang¹, Ziming Zheng¹, Bo Yan¹, Jiyuan Lv¹

Journal of Renewable Materials, DOI:10.32604/jrm.2022.022296

Abstract A calculation model of stress field in laser additive manufacturing of walnut shell composite powder (walnut shell/Co-PES powder) was established. The DFLUX subroutine was used to implement the moveable application of a double ellipsoid heat source by considering the mechanical properties varying with temperature. The stress field was simulated by the sequential coupling method, and the experimental results were in good accordance with the simulation results. In addition, the distribution and variation of stress and strain field were obtained in the process of laser additive manufacturing of walnut shell composite powder. The displacement of laser More >

Aman Santoso^1,*, Amirotus Sholikhah¹, Sumari Sumari¹, Muhammad Roy Asrori¹, Anugrah Ricky Wijaya¹, Rini Retnosari^1,2, Ihsan Budi Rachman^1,3

Journal of Renewable Materials, DOI:10.32604/jrm.2022.021401

Abstract Plastic is a basic need for humans, but it has also caused big problems for the environment. Then, the purpose of this study was to determine the effect of the type of plastic and the addition of a zeolite catalyst on the oil yield from the pyrolysis of plastic waste. The research stages were natural zeolite activation, pyrolysis reactor settings, pyrolysis of plastic waste (PP and LDPE types), and characterization. The results showed that the used natural zeolite had a mordenite phase and activated natural zeolite had a higher Si/Al ratio than the inactivated one.… More >

Yanfei Feng, Jiaming Lin, Longxing Niu, Peng Pan, Xueping Liu, Linling Huang, Ying Guo, Mingzhong Li^*

Journal of Renewable Materials, DOI:10.32604/jrm.2022.021339

Abstract The development of a method for the quantitative determination of the sericin content ratio (SCR) is urgently needed for silk refining and the purification of silk fibroin for biomedical applications. In this work, a series of sericin/fibroin mixed samples with known SCRs were prepared by mixing initial samples of extracted sericin and fibroin from Bombyx mori silk. Significant differences were found in the contents of characteristic hydrophilic amino acids abundant in sericin and hydrophobic amino acids abundant in fibroin, and several linear relationships of SCR associated with the content ratios of Ser/Ala, Asp/Ala, Lys/Ala, Asp/Gly and… More >

Usama Sayed^1,2, Assima Dauletbek^1,2, Xue Xin^1,2, Rodolfo Lorenzo³, Haitao Li^1,2,*

Journal of Renewable Materials, DOI:10.32604/jrm.2022.022624

Abstract In light of the increasing demand for sustainable building materials, the effectiveness of bamboo utilization in various fields has become the object of scientists’ close attention. The increased interest in bamboo is explained by its sustainable characteristics, which make it the most preferred material for environmentally friendly and costeffective construction compared to conventional ones. Applicability of bamboo is vast and diverse: from decoration and furniture to structural members and reinforcement. Due to the low price, rich resources, and high elasticity, bamboo culms have also been used as an alternative to steel reinforcement in concrete structures. More >

Mahdi Hosseini^1,2,*, Bingyu Jian^1,2, Haitao Li^1,2,*, Dong Yang^1,2, Ziang Wang^1,2, Zixian Feng^1,2, Feng Shen³, Jian Zhang⁴, Rodolfo Lorenzo⁵, Ileana Corbi⁶, Ottavia Corbi⁶

Journal of Renewable Materials, DOI:10.32604/jrm.2022.022171

Abstract The use of fibre-reinforced polymer (FRP) to confine concrete columns improves the strength and ductility of the columns by reducing passive lateral confinement pressure. Many numerical and analytical formulations have been proposed in the literature to describe the compressive behaviour of FRP confined concrete under both monotonic and cyclic loads. However, the effect of a stress/strain level in the columns has not been well defined because of the lack of well-defined strategies of modelling and oversimplification of the model. This paper reviews the existing FRP combinations and the available numerical and analytical methods to determine More >

Norshariza Mohamad Bhkari^1,2,*, Lum Wei Chen¹, Anis Azmi², Muhammad Shaiful Nordin², Norman Wong Shew Yam³, Zakiah Ahmad², Lee Seng Hua⁴

Journal of Renewable Materials, DOI:10.32604/jrm.2022.022326

Abstract This study investigated the bending, compression as well as the bonding performance of CLT panels made from fast-growing timber species, i.e., Laran (Neolamarckia cadamba) and Batai (Paraserianthes falcataria). The variables studied were timber species (Laran and Batai), layers of lamination (3-layer and 5-layer), loading direction in bending (in-plane and out-of-plane), loading direction in compression (x-, y-, and z-axis) and different treatment conditions for bonding performance test. The desired outputs of this study were bending and compression properties (strength and stiffness) as well as bonding performance (block shear strength, wood failure percentage and delamination value). The bending and… More >

Jianhua Lyu^1,2,#, Jialei Wang^1,2,#, Ziqiang Chen³, Ming Chen^1,2,*

Journal of Renewable Materials, DOI:10.32604/jrm.2022.021478

Abstract The traditional tenon and mortise joint has low processing efficiency and a weak theoretical basis, making the structure easy to deform and damage, reducing the safety, and increasing waste of resources. This study aims to determine the optimum dowel center spacing parameter for chamfered-joint components and the maximum value of the strength of joints loaded into bending strength and tensile strength. In this study, an integrated optimization method combining the single-factor test and one-way ANOVA analysis was proposed to study the influence of the dowel center spacing on the bending strength and the tensile strength More >