W. F. Yuan^1,2, H. B. Zhang¹

CMC-Computers, Materials & Continua, Vol.16, No.2, pp. 117-126, 2010, DOI:10.3970/cmc.2010.016.117

Abstract Corrosion pits on a steel plate can reduce the strength of the plate. However, it is difficult to calculate the corrosion effect analytically since the pits are normally distributed on the plate's surface randomly. In this manuscript, a simple approach is proposed to convert the corroded plate into a perfect one. By this method, the corrosion pits are treated as inclusions embedded in the plate. Then the analytical mechanics model used for composite material can be adopted in the calculation of the steel plate's effective material properties. To verify the proposed approach, numerical simulation is conducted using finite element method. More >

J. Zidek¹ , J. Kucera¹, J. Jancar¹

CMC-Computers, Materials & Continua, Vol.16, No.1, pp. 51-74, 2010, DOI:10.3970/cmc.2010.016.051

Abstract It has been shown that in particulate filled composites, a cross-property relationship exists between various transport properties (e.g., electrical conductivity, mechanical reinforcement, gas permeation) of a macroscale composite. Thus, knowledge of the effective mechanical properties of a composite immediately places bounds on its electrical conductivity or gas permeation behavior. Using these bounds allows us to predict the phase dispersion state that optimizes one or multiple properties of the composite and, thus, the knowledge of how spatial arrangement of filler particles at their given content affects physical properties of the composite can be valuable. In this paper, a new numerical model… More >

M. Vogler¹, G. Ernst¹, R. Rolfes¹

CMC-Computers, Materials & Continua, Vol.16, No.1, pp. 25-50, 2010, DOI:10.3970/cmc.2010.016.025

Abstract In this article, a constitutive formulation of a transversely-isotropic material and failure model for fiber-reinforced polymers is presented comprising pre-failure material nonlinearities, a novel invariant based quadratic failure criterion (IQC) as well as post failure material softening. The failure surface of the IQ criterion is assumed to take the influence of triaxiality on fracture into account. Further, a distinction between fiber failure and inter-fiber failure is conducted. Material softening is governed by a fracture energy formulation and the introduction of an internal length. The constitutive model is implemented into a programming user interface of the commercial finite element program Abaqus.… More >

Chen Y J^1,2, Huber N^2,3

CMC-Computers, Materials & Continua, Vol.16, No.1, pp. 1-24, 2010, DOI:10.3970/cmc.2010.016.001

Abstract An efficient wear integration algorithm is crucial for the simulation of wear in complex transient contact situations. By rewriting Archard's wear law for two dimensional problems, the wear integration can be replaced by the total contact force. This avoids highly resolved simulations in time and space, so that the proposed method allows a significant acceleration of wear simulations. All quantities, including the average contact velocity, slip rate and total contact force, which are required for the pressure-force transformation, can be determined from geometric and motion analysis, or alternatively, from Finite Element simulations. The proposed CForce method has been implemented into… More >

Luming Shen¹

CMC-Computers, Materials & Continua, Vol.15, No.3, pp. 241-260, 2010, DOI:10.3970/cmc.2010.015.241

Abstract In this study, molecular dynamics (MD) simulations are performed to form glassy silica from meltedb-cristobalite using cooling rates of 2, 20 and 200 K/ps. The resulting glassy silica samples are then shocked at particle velocities ranging from 0.3 to 11 km/s in the MD simulations. The effect of the cooling rate on the shock wave velocity is observed for particle velocities below 2 km/s. Moreover, the simulated pressure and density of the shocked glassy silica increase as the cooling rate increases. As compared with the experimental data, the MD simulation can approximately identify the initiation of densification and predict the… More >

Chein-Shan Liu¹

CMC-Computers, Materials & Continua, Vol.15, No.3, pp. 221-240, 2010, DOI:10.3970/cmc.2010.015.221

Abstract We propose a simple numerical scheme for solving the space- and time-fractional derivative Burgers equations: D_t^αu + εuu_x = vu_xx + ηD_x^βu, 0 < α, β ≤ 1, and u_t + D_*^β(D_*^1-βu)²/2 = vu_xx, 0 < β ≤ 1. The time-fractional derivative D_t^αu and space-fractional derivative D_x^βu are defined in the Caputo sense, while D_*^βu is the Riemann-Liouville space-fractional derivative. A fictitious time τ is used to transform the dependent variable u(x,t) into a new one by (1+τ)^γu(x,t) =: v(x,t,τ), where 0 < γ ≤ 1 is a parameter, such that the original equation is written as a new functional-differential… More >

F.Y.Li^1,2, G.Y.Li¹

CMC-Computers, Materials & Continua, Vol.15, No.3, pp. 199-220, 2010, DOI:10.3970/cmc.2010.015.199

Abstract In this paper, an uncertain multi-objective optimization method is suggested to deal with crashworthiness design problem of vehicle, in which the uncertainties of the parameters are described by intervals. Considering both lightweight and safety performance, structural weight and peak acceleration are selected as objectives. The occupant distance is treated as constraint. Based on interval number programming method, the uncertain optimization problem is transformed into a deterministic optimization problem. The approximation models are constructed for objective functions and constraint based on Latin Hypercube Design (LHD). Thus, the interval number programming method is combined with the approximation model to solve the uncertain… More >

Hrvoje Gotovac¹, Vedrana Kozulić², Blaž Gotovac¹

CMC-Computers, Materials & Continua, Vol.15, No.3, pp. 173-198, 2010, DOI:10.3970/cmc.2010.015.173

Abstract The space-time Adaptive Fup Collocation Method (AFCM) for solving boundary-initial value problems is presented. To solve the one-dimensional initial boundary value problem, we convert the problem into a two-dimensional boundary value problem. This quasi-boundary value problem is then solved simultaneously in the space-time domain with a collocation technique and by using atomic Fup basis functions. The proposed method is a generally meshless methodology because it requires only the addition of collocation points and basis functions over the domain, instead of the classical domain discretization and numerical integration. The grid is adapted progressively by setting the threshold as a direct measure… More >

Hamad F. Al-Harbi¹, Marko Knezevic^1,2, Surya R. Kalidindi^1,3

CMC-Computers, Materials & Continua, Vol.15, No.2, pp. 153-172, 2010, DOI:10.3970/cmc.2010.015.153

Abstract In recent work, we have demonstrated the viability and computational advantages of DFT-based spectral databases for facilitating crystal plasticity solutions in face-centered cubic (fcc) metals subjected to arbitrary deformation paths. In this paper, we extend and validate the application of these novel ideas to body-centered cubic (bcc) metals that exhibit a much larger number of potential slip systems. It was observed that the databases for the bcc metals with a larger number of slip systems were more compact compared to those obtained previously for fcc metals with a smaller number of slip systems. Furthermore, we demonstrate in this paper that… More >

Dustin D. Gerrard¹, David T. Fullwood¹, Denise M. Halverson², Stephen R. Niezgoda³

CMC-Computers, Materials & Continua, Vol.15, No.2, pp. 129-152, 2010, DOI:10.3970/cmc.2010.015.129

Abstract The effective properties of composite materials are often strongly related to the connectivity of the material components. Many structure metrics, and related homogenization theories, do not effectively account for this connectivity. In this paper, relationships between the topology, represented via homology theory, and the effective elastic response of composite plates is investigated. The study is presented in the context of popular structure metrics such as percolation theory and correlation functions. More >