Yabin Yang, Guangyu Shi^*

The International Conference on Computational & Experimental Engineering and Sciences, Vol.21, No.2, pp. 35-35, 2019, DOI:10.32604/icces.2019.05623

Abstract The efficient and high performance orthotropic steel decks have been widely used in long span bridges over the world. The initial defects at welded joints of orthotropic steel bridge decks will undergo fatigue failure under the action of live load of moving vehicles on the bridge decks. And the fatigue cracks at the rib-to-deck welded joints are the most dangerous cracks for the orthotropic steel bridge decks. Therefore, the fatigue life evaluation of the rib-to-deck welded joints is very important for the safety of orthotropic steel bridge decks. This paper presents a crack propagation-based model for the fatigue life prediction… More >

E. Schnack¹, A. Dimitrov², F.-G. Buchholz³

The International Conference on Computational & Experimental Engineering and Sciences, Vol.1, No.4, pp. 139-146, 2007, DOI:10.3970/icces.2007.001.139

Abstract In fracture mechanics, we have to discuss corner and edge singularities for two- and three-dimensional problems in isotropic and layered anisotropic continua. To say something about the behavior of crack propagation starting from corners and edges, we need the information about stress asymptotics in the vicinity of three-dimensional corner points. Thus, in this paper we can study two aspects: the interface crack in layered unisotropic materials with re-entrant corners and surface cracks for the homogeneous isotropic continua. To study the effect of geometrical singularities on the stress intensity factors, we have to define generalized stress intensity factors. We are starting… More >

Milazzo A.¹, aimo A.¹, Orl,o C.¹

The International Conference on Computational & Experimental Engineering and Sciences, Vol.1, No.2, pp. 69-74, 2007, DOI:10.3970/icces.2007.001.069

Abstract In this paper a Hierarchical approach for the analysis of advanced aerospace structures is presented. The proposed Global/Local model uses two kind of numerical methods for the different steps of analysis. In particular the first step of the Hierarchical procedure is performed by the Finite Element code Patran/NastranTM, while the local analysis is performed by using a Boundary Element code based on the multidomain anisotropic technique. The accuracy and the effectiveness of the model have been demonstrated analysing classical stress concentration problems. Then the procedure has been used to analyze more complex structure among which a riveted patch repair, applied… More >

R. Matsumoto¹, M. Nakagaki¹, A. Nakatani², H. Kitagawa³

CMES-Computer Modeling in Engineering & Sciences, Vol.9, No.1, pp. 75-84, 2005, DOI:10.3970/cmes.2005.009.075

Abstract In this paper, the internal structure-changes around the crack-tip and the pertinent crack growth behavior in an amorphous metal were studied by a molecular dynamics (MD) simulation. In order to perform a large scale calculation, the domain decomposition method was used for parallel calculation. The Finnis-Sinclair potential for$\alpha$-iron was used to describe the interatomic potential. Computed results show that nano-scaled crystalline phase grows around the crack-tip. The distribution of deformation zones and deformation mechanism are significantly altered. While grains are relatively small, they are not deformed, and the most amorphous-crystal interfaces have a large strain for phase transition. The emission… More >

Wen-Hwa Chen¹, Cheng-Hung Chen²

CMES-Computer Modeling in Engineering & Sciences, Vol.8, No.3, pp. 177-190, 2005, DOI:10.3970/cmes.2005.008.177

Abstract An enriched meshless method, using meshless interpolations and a global Galerkin approach, is developed for the analysis of three-dimensional fracture problems. The displacement field which accounts for the stress singularity nearby the crack front and the boundary layer effect at the intersection between the crack front and the free surface of the structure is adopted to enrich the trial functions. The three-dimensional stress intensity factors can thus be treated as independent unknown parameters and calculated with the nodal displacements directly. To estimate the accuracy of the method developed, several representative three-dimensional cracks are analyzed. These include single-edge crack, embedded elliptical… More >

J. Purbolaksono¹, M. H. Aliabadi^2,3

CMES-Computer Modeling in Engineering & Sciences, Vol.8, No.1, pp. 73-90, 2005, DOI:10.3970/cmes.2005.008.073

Abstract This paper presents the dual boundary integral equations for the buckling analysis of the shear deformable cracked plates. The domain integrals which appear in this formulation are transferred to boundary integrals using the dual reciprocity method. The plate buckling displacement and hypersingular traction integral equations are presented as a standard eigenvalue problem, which would allow direct evaluation of the critical load factor and buckling modes. Several examples with different geometries and boundary conditions are presented to demonstrate the accuracy of the proposed formulation. More >

Bernal Sibaja^1,2,3, Camila Pereira Matheus^1,2, Ricardo Ballestero Mendez^1,2,Ramsis Farag^1,2,4, J. R. Vega-Baudrit³, Maria L. Auad^*,1,2

Journal of Renewable Materials, Vol.5, No.3-4, pp. 241-250, 2017, DOI:10.7569/JRM.2017.634114

Abstract The thermo-mechanical properties and linear fracture mechanics of acrylated soybean oil and the triglycidylated ether of α-resorcylic acid interpenetrated networks as a function of their weight composition are the focus of Part 2 of this article. Thermo-mechanical characterization showed that the obtained materials behave as thermoset amorphous polymers, and that both the modulus and glass transition are extremely dependent on the epoxy/acrylate weight ratio. Modulus values ranged from 0.7 to 3.3 GPa at 30 °C, and glass transition temperatures ranged from around 58 °C to approx. 130 °C. No synergistic effect on these two properties was observed. Interpenetrating networks containing… More >

A. Rama Chandra Murthy¹, G.S. Palani¹, Nagesh R. Iyer¹

CMC-Computers, Materials & Continua, Vol.1, No.4, pp. 289-300, 2004, DOI:10.3970/cmc.2004.001.289

Abstract In this paper an improved Wheeler residual stress model has been proposed for remaining life assessment of cracked plate panels under variable amplitude loading (VAL). The improvement to the Wheeler residual stress model is in terms of the expressions for the shaping exponent, which is generally obtained through experiments. Simple expressions for the computation of shaping exponent have been proposed for compact tension (CT) specimen and plate panels with a center crack or an edge crack. The remaining life assessment has been carried out by employing linear elastic fracture mechanics (LEFM) principles. In the present study, the degree of influence… More >

Yasunori Yusa¹, Shinobu Yoshimura¹

CMES-Computer Modeling in Engineering & Sciences, Vol.99, No.1, pp. 87-104, 2014, DOI:10.3970/cmes.2014.099.087

Abstract To speed up the elastic–plastic analysis of a large-scale model with a crack in which plasticity is observed near the crack, the partitioned coupling method is applied. In this method, the entire analysis model is decomposed into two non-overlapped domains (i.e., global and local domains), and the two domains are analyzed with an iterative method. The cracked local domain is modeled as an elastic–plastic body, whereas the large-scale global domain is modeled as an elastic body. A subcycling technique is utilized for incremental analysis to reduce the number of global elastic analyses. For a benchmark problem with 6 million degrees… More >

Y.C. Shiah¹, C.L. Tan², Y.H. Chen³

CMES-Computer Modeling in Engineering & Sciences, Vol.96, No.4, pp. 243-257, 2013, DOI:10.3970/cmes.2013.096.243

Abstract The present authors have recently proposed an efficient, alternative approach to numerically evaluate the fundamental solution and its derivatives for 3D general anisotropic elasticity. It is based on a double Fourier series representation of the exact, explicit form of the Green’s function derived by Ting and Lee (1997). This paper reports on the successful implementation of the fundamental solution and its derivatives based on this Fourier series scheme in the boundary element method (BEM) for 3D general anisotropic elastostatics. Some numerical examples of stress concentration problems and a crack problem are presented to demonstrate the veracity of the implementation. The… More >