Suxia Li^1,2, Haiyang Zhang^1,*, Biqing Shu^1,3, Liangsong Cheng¹, Zehui Ju¹, Xiaoning Lu^1,*

Journal of Renewable Materials, Vol.9, No.7, pp. 1225-1237, 2021, DOI:10.32604/jrm.2021.014364

Abstract The wood friction welding technique with its high bonding strength, low cost, high efficiency, and without any adhesive has been increasing concern in China. Moso bamboo (Phyllostachys pubescens) and poplar (Populus sp.) are widely planted and used in the furniture industry, interior decoration, and wood structure construction in China. The aim of this work was to investigate the bonding performance of moso bamboo dowel rotation welded joints with different dowel/receiving hole diameter ratios. The results indicated that the ratio of dowel/receiving hole diameter was an important parameter that influenced the welding performance. The bonding strength of the bamboo-to-poplar welded joints… More >

Rongfeng Chen¹, Changqing Miao^2,*

Structural Durability & Health Monitoring, Vol.14, No.3, pp. 205-228, 2020, DOI:10.32604/sdhm.2020.08997

Abstract In order to study the fatigue properties of rib-to-deck welded connection and rib-to-rib welded connection in orthotropic steel bridge decks, a multi-scale finite element model was set up to analyze the stress distribution characteristics and the load test was conducted on the Taizhou Yangtze River Bridge. Comparing the vehicle test results with the multi-scale finite element model results to verify the accuracy of the finite element simulation for the stress response of two welded details. The results indicated that: The stress at the rib-to-deck welded connection and the rib-to-rib welded connection are the bending stress and the membrane stress, respectively;… More >

Mohamed Ben Gharsallah^a, Issam Ben Mhammed^b, Ezzedine Ben Braiek^a

Intelligent Automation & Soft Computing, Vol.24, No.2, pp. 231-240, 2018, DOI:10.1080/10798587.2016.1262457

Abstract In radiography imaging, contrast, sharpness and noise there are three fundamental factors that determine the image quality. Removing noise while preserving and sharpening image contours is a complicated task particularly for images with low contrast like radiography. This paper proposes a new anisotropic diffusion method for radiography image enhancement. The proposed method is based on the integration of geometric parameters derived from the local pixel intensity distribution in a nonlinear diffusion formulation that can concurrently perform the smoothing and the sharpening operations. The main novelty of the proposed anisotropic diffusion model is the ability to combine in one process noise… More >

Junyan Ni¹, Xincun Zhuang^{2, 3}, Magd Abdel Wahab^{4, 5, *}

CMC-Computers, Materials & Continua, Vol.62, No.2, pp. 495-523, 2020, DOI:10.32604/cmc.2020.08448

Abstract Residual stress after welding has negative effects on the service life of welded steel components or structures. This work reviews three most commonly used methods for predicting residual stress, namely, empirical, semi-empirical and process simulation methods. Basic principles adopted by these methods are introduced. The features and limitations of each method are discussed as well. The empirical method is the most practical but its accuracy relies heavily on experiments. Mechanical theories are employed in the semi-empirical method, while other aspects, such as temperature variation and phase transformation, are simply ignored. The process simulation method has been widely used due to… More >

F. Balle¹, S. Huxhold¹, G. Wagner¹, D. Eifler¹

Structural Durability & Health Monitoring, Vol.8, No.4, pp. 359-370, 2012, DOI:10.32604/sdhm.2012.008.359

Abstract Aluminum alloys and carbon fiber reinforced polymers (CFRP) are two important materials for lightweight design and the combination of these dissimilar materials becomes increasingly important. Recent investigations have shown that ultrasonic metal welding is a well suited process to realize aluminum/CFRP-joints.The ultrasonic shear oscillation parallel to the welding zone with a simultaneous welding force perpendicular to the aluminum/CFRP-sheets melts the polymer matrix and squeezes the polymer matrix out of the welding zone. This allows a direct contact between the carbon fibers and the aluminum. Beside monotonic properties the cyclic deformation behavior of these ultrasonically welded aluminum/CFRP-joints is essential. Therefore in… More >

K.N. Song¹

Structural Durability & Health Monitoring, Vol.8, No.3, pp. 209-222, 2012, DOI:10.32604/sdhm.2012.008.209

Abstract A PHE (Process Heat Exchanger) is a key component in transferring the high temperature heat generated from a VHTR (Very High Temperature Reactor) to the chemical reaction for the massive production of hydrogen. A performance test on a small-scale PHE prototype made of Hastelloy-X is currently under way a small-scale gas loop at the Korea Atomic Energy Research Institute. Previous research on the elastic high-temperature structural analysis of the small-scale PHE prototype has been performed using the parent material properties over the whole region. In this study, an elastic-plastic high-temperature structural analysis considering the mechanical properties in the weld-affected zone… More >

G. Meneghetti¹

Structural Durability & Health Monitoring, Vol.8, No.2, pp. 111-130, 2012, DOI:10.3970/sdhm.2012.008.111

Abstract This paper deals with the local approach based on the Notch Stress Intensity Factors (NSIFs) to analyse the fatigue behavior of welded joints. In transverse load carrying fillet-welded joints, failure may occur either at the toe or at the root, depending on the geometry. At the toe, due to the flank angles that are usually encountered in practice, mode I local stresses are singular, while mode II stresses are not. Conversely, at the root of the particular joints analysed in the present paper both mode I and mode II stresses are singular and must be taken into account in fatigue… More >

A. Lanciotti, L. Lazzeri¹, C. Polese², C. Rodopoulos³, P. Moreira^4,5, A. Brot⁶, G. Wang⁷, L. Velterop⁸, G. Biallas⁹, J. Klement

Structural Durability & Health Monitoring, Vol.7, No.3, pp. 211-230, 2011, DOI:10.3970/sdhm.2011.007.211

Abstract An experimental activity was performed to collect test data on the fatigue crack propagation in various types of specimens, within the DaToN research project, partly funded by the EU in the FP6 programme. Only one general configuration was used, i.e. flat panels with two blade stringers, with different options for the manufacturing processes, that could be integral or welded. The purpose of this test activity was to obtain useful results for the validation and calibration of prediction methodologies, also developed in the same DaToN research project. A wide experimental programme was defined and performed by many laboratories; the materials investigated… More >

M. M. Rahman¹, A. K. Arrifin², M. J. M. Nor², S. Abdullah²

Structural Durability & Health Monitoring, Vol.4, No.3, pp. 173-180, 2008, DOI:10.3970/sdhm.2008.004.173

Abstract This paper presents the fatigue analysis of spot-weld joints for automative structures to predict the lifetime and location of the weakest spot-welds due to the imposed loading conditions. A simple model was used to illustrate the technique of spot-weld fatigue analysis. Finite element model and analysis were carried out utilizing the finite element analysis commercial codes. Linear elastic finite element analysis was carried out to predict the stress state along the weld direction. It can be seen from the results that the predicted life greatly influence the sheet thickness, spot diameter and loading conditions of the model. Acquired results were… More >

L. Fratini¹, S. Pasta²

Structural Durability & Health Monitoring, Vol.1, No.4, pp. 245-252, 2005, DOI:10.3970/sdhm.2005.001.245

Abstract In the last years friction stir welding (FSW) has reached a quite large diffusion in the welding of aluminium alloys, difficult to be welded with traditional technologies. The objective of this investigation was to investigate the influence of FSW process parameters on the fatigue strength of the developed joints. Moreover, in order to improvement the strength of joint, the effect of a post-welding treatment has been highlighted; what is more a surface finish treatment has been developed with the aim to eliminate the stress concentration caused by welding process on the surface of the joints. Finally, the fracture locations have… More >