Raveendranath U Nair¹, R M Jha¹

CMC-Computers, Materials & Continua, Vol.37, No.2, pp. 109-121, 2013, DOI:10.3970/cmc.2013.037.109

Abstract Enhancement of electromagnetic performance of A-sandwich radome using aperture-type Jerusalem cross frequency selective surface (FSS) is presented. The Jerusalem cross FSS array is embedded in the mid-plane of the core of Asandwich radome to enhance the EM performance parameters over the entire Xband. For modeling the Jerusalem cross FSS embedded radome panel and evaluation of its EM performance parameters, equivalent transmission line method in conjunction with equivalent circuit model is used. A comparative study of Jerusalem cross FSS embedded A-sandwich radome and A-sandwich radome of identical material and thickness (core and skin layers) indicate that the new wall configuration has… More >

Shiv Narayan¹, R M Jha¹

CMC-Computers, Materials & Continua, Vol.37, No.2, pp. 97-108, 2013, DOI:10.3970/cmc.2013.037.097

Abstract A novel metamaterial based FSS (frequency selective surfaces) structure is presented in this paper for wideband airborne radome applications. The proposed metamaterial-FSS structure consists of three layers, where a DPS (double positive sign) layer is sandwiched between a MNG (μ-negative) and ENG (ε- negative) layer, exhibits very good bandpass characteristics inside the operational band along with excellent roll-off characteristics outside the band. The EM performance analysis of the proposed structure has been carried out using transmission line transfer matrix (TLTM) method, which shows excellent bandpass characteristics over a wide frequency range. The transmission efficiency is over 95% both at normal… More >

A. Ramachandra Murthy¹, G.S. Palani¹, Smitha Gopinath¹, V. Ramesh Kumar¹, Nagesh R. Iyer¹

CMC-Computers, Materials & Continua, Vol.37, No.2, pp. 77-96, 2013, DOI:10.3970/cmc.2013.037.077

Abstract This paper presents the development of an improved concrete damage model for projectile impact on concrete structural components. The improvement is in terms of reduction of input material parameters for nonlinear transient dynamic impact analysis by employing concrete damage model. The experimental data such as pressure vs volumetric strain, triaxial compression failure and pressure vs stress difference have been used for evaluation of the important parameters of concrete damage model. Various contact algorithms have been outlined briefly to model the interface between the projectile and target. The nonlinear explicit transient dynamic analysis has been carried out by using finite element… More >

J. Joseph¹, Y. C. Lu¹

CMC-Computers, Materials & Continua, Vol.37, No.1, pp. 59-75, 2013, DOI:10.3970/cmc.2013.037.059

Abstract The aligned carbon nanotube (A-CNT) structure is composed of arrays of individual CNTs grown vertically on a flat substrate. The overall structure and properties of an A-CNTs are highly dependent upon the designs of various architectures and geometric parameters. In Part 2, we have presented the detailed designs and modeling of various aligned carbon nanotube structures. It is found the A-CNT structures generally have much lower modulus than an individual CNT. The reason is due to the high porosity and low density of the A-CNT structures, since the interstitial space between nanotubes is mostly occupied by air. Increasing the nanotube… More >

J. Joseph¹, Y. C. Lu¹

CMC-Computers, Materials & Continua, Vol.37, No.1, pp. 39-57, 2013, DOI:10.3970/cmc.2013.037.039

Abstract Aligned carbon nanotubes structures are emerging new materials that have demonstrated superior mechanical, thermal, and electrical properties and have the huge potential for a wide range of applications. In contrast with traditional materials whose microstructures are relatively "fixed", the aligned carbon nanotube materials have highly "tunable" structures. Therefore, it is crucial to have a rational strategy to design and evaluate the architectures and geometric factors to help process the optimal nanotube materials. Astructural mechanics based computational modeling is used for designing the aligned carbon nanotubes structures. Part 1 of the papers presents the theory of the computational method as well… More >

M. Marin¹, S. R. Mahmoud^2,3, K. S. Al-Basyouni⁴

CMC-Computers, Materials & Continua, Vol.37, No.1, pp. 23-37, 2013, DOI:10.3970/cmc.2013.037.023

Abstract Taking advantage of the flexibility of Lagrange’s identity, we prove the uniqueness theorem and some continuous dependence theorems without recourse to any energy conservation law, or to any boundedness assumptions on the constitutive coefficients. Also, we avoid the use of positive definiteness assumptions on the constitutive coefficients, even if these results are related to the difficult mixed problem in elasticity of micromorphic bodies. More >

Leiting Dong^1,2, Salah H. Gamal³, Satya N. Atluri^2,4

CMC-Computers, Materials & Continua, Vol.37, No.1, pp. 1-21, 2013, DOI:10.3970/cmc.2013.037.001

Abstract In this paper, a simple and reliable procedure of stochastic computation is combined with the highly accurate and efficient Trefftz Computational Grains (TCG), for a direct numerical simulation (DNS) of heterogeneous materials with microscopic randomness. Material properties of each material phase, and geometrical properties such as particles sizes and distribution, are considered to be stochastic with either a uniform or normal probabilistic distributions. The objective here is to determine how this microscopic randomness propagates to the macroscopic scale, and affects the stochastic characteristics of macroscopic material properties. Four steps are included in this procedure: (1) using the Latin hypercube sampling,… More >

E. Ferretti¹

CMC-Computers, Materials & Continua, Vol.36, No.3, pp. 293-322, 2013, DOI:10.3970/cmc.2013.036.293

Abstract The Cell Method is applied in order to model the debonding mechanism in ceramic floor tiles subjected to positive thermal variation. The causes of thermal debonding, very usual in radiant heat floors, have not been fully clarified at the moment. There exist only a few simplified analytical approaches that assimilate this problem to an eccentric tile compression, but these approaches introduce axial forces that, in reality, do not exist. In our work we have abandoned the simplified closed form solution in favor of a numerical solution, which models the interaction between tiles and sub-base more realistically, when the positive thermal… More >

Zichun Yang^1,2,3, Gaohui Su^1,4, Fengrui Sun¹

CMC-Computers, Materials & Continua, Vol.36, No.3, pp. 271-292, 2013, DOI:10.3970/cmc.2013.036.271

Abstract In this paper, we investigate the radiative properties and the effective thermal conductivity (ETC) of the opacified silica aerogel by theoretical method. The radiative properties of the opacified silica aerogel are obtained by the modified Mie Scattering Theory that is used for particle scattering in absorbing medium. The modified gamma distribution is used to take account of the non-uniformity of the particle size. The solid thermal conductivity of the composite material is obtained by considering the scale effect of the particles. Based on these calculated thermophysical properties the coupled heat conduction and radiation through the evacuated opacified aerogel are solved… More >

Sanjeev Saxena¹, Raghvendra Singh², Geeta Agnihotri²

CMC-Computers, Materials & Continua, Vol.36, No.3, pp. 257-270, 2013, DOI:10.3970/cmc.2013.036.257

Abstract The present numerical study is an attempt to understand the dependency of characteristic distance on the fracture specimen thickness and temperature. The presented work will be useful to establish the characteristic distance prediction methodology using three dimensional FEM model. Based on the methods proposed for the numerical prediction of characteristic distance, it comes out that it depends on fracture specimen thickness and finally it converges after a specified thickness of fracture specimen. In Armco iron material, characteristic distance varies in temperature ranges where dynamic strain ageing phenomenon is observed, initially decrease and then increases again. More >