Joel Koti^1,2,*, Crespin P. Yabi³, Mohamed Gibigaye¹, Anne Millien², Christophe Petit²

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1469-1482, 2022, DOI:10.32604/fdmp.2022.021902 - 27 May 2022

Abstract In tropical areas, palm oil production generates significant amounts of waste, including palm kernel shells. The use of this waste in the civil engineering sector, presents a very challenging task. In the present study, the production of lateritic soil (A-2 in GTR classification and A-7-6 (9) in HRB classification) reinforced with palm kernel shells is considered. In order to improve their performances, these materials are mixed using the Fuller’s parabolic law. Moreover, experimental tests are used to characterize the physical and mechanical geotechnical properties of the lateritic soil. After characterizing the matrix (i.e., lateritic soil)… More >

Brahim Amahan¹, Hamid El Qarnia^2,*, Ali El Afif¹

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1539-1549, 2022, DOI:10.32604/fdmp.2022.021839 - 27 May 2022

Abstract This paper numerically investigates the effect of the location of a horizontal fin on the melting of a phase change material (PCM) inside a rectangular enclosure heated by multiple discrete pulsed protruding heat sources. The fin and the phase change material filling the enclosure store the thermal energy extracted from the heat sources, in sensible and latent forms. The heat sources are assumed to simulate electronic components undergoing a superheating technical issue. By extracting heat from the electronics, the PCM plays the role of a heat sink. To analyze the thermal behavior and predict the… More >

Larbi Afif^*, Nahla Bouaziz

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1243-1251, 2022, DOI:10.32604/fdmp.2022.021831 - 27 May 2022

Abstract In the present work, a novel Organic Rankine Cycle (ORC) configuration is used for a low-grade heat source cogeneration plant. An investigation is conducted accordingly into the simultaneous production of electricity and cold. The proposed configuration relies on concentrated solar power (as heat source) and ambient air (for cooling). Furthermore, two gas ejectors are added to the system in order to optimize the thermodynamic efficiency of the organic Rankine cycle. The results show that the thermodynamic and geometric parameters related to these ejectors have an important effect on the overall system performances. In order to More >

Yazid Statra, Sara Fawaz, Hocine Menana^*, Bruno Douine

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1529-1537, 2022, DOI:10.32604/fdmp.2022.021827 - 27 May 2022

Abstract The electromagnetic properties of high temperature superconductors (HTS) are characterized with the explicit intent to improve their integration in electric power systems. A tape and a coil made of Bismuth Strontium Calcium Copper Oxide (BSCCO) are considered in the presence of electromagnetically active materials in order to mimic properly the electromagnetic environment typical of electrical machines. The characterization consists of the determining the critical current and the AC losses at different values of the frequency and the transport current. The effects induced by the proximity of the active materials are studied and some related experimental More >

Fatima Zohra Elhilali, Hicham Fihri-Fassi^*

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1285-1292, 2022, DOI:10.32604/fdmp.2022.021803 - 27 May 2022

Abstract In order to mitigate the risks stemming from the utilization of mineral and synthetic organic substances, consensus exists in the literature that additional efforts should be devoted to the identification of adequate equivalent natural (ecological) materials. This work presents the outcomes of a preliminary study where the physical, mechanical, chemical and thermal properties of natural fibers have been considered. Initially, areca, and materials such as Moroccan doum and jute are considered. As a case study, a brake pad based on natural fibers is critically assessed. More >

Mourad Najjaoui^1,*, Thami Ait-taleb¹, Abdelhalim Abdelbaki², Zaki Zrikem², Hassan Chaib¹

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1399-1407, 2022, DOI:10.32604/fdmp.2022.021760 - 27 May 2022

Abstract This work presents the results of a set of steady-state numerical simulations about heat transfer in hollow blocks in the presence of coupled natural convection, conduction and radiation. Blocks with two air cells deep in the vertical direction and three identical cavities in the horizontal direction are considered (typically used for building ceilings). Moreover, their outside horizontal surface is subjected to an incident solar flux and outdoor environment temperature while the inside surface is exposed to typical indoor environment conditions. The flows are considered laminar and two-dimensional over the whole range of parameters examined. The More >

Redouane En-nadir^1,*, Haddou El-ghazi², Anouar Jorio¹, Izeddine Zorkani¹, Hassan Abboudi¹, Fath Allah Jabouti¹

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1253-1261, 2022, DOI:10.32604/fdmp.2022.021759 - 27 May 2022

Abstract In this paper, we theoretically investigate the total optical coefficient (TOAC) considering 1S-2P and 2S-2P conduction subband transitions in a single parabolic quantum well (SPQW) with an on-center hydrogen-like impurity. Within the framework of the effective-mass approximation, the Schrödinger equation is solved numerically to obtain the eigenvalues and their corresponding eigenvectors using the finite difference method. The calculations are performed for finite confinement potential height, taking into account the dielectric and effective mass mismatches between GaN and InGaN materials under the considered electric field and temperature effects. The temperature dependence of the effective mass, dielectric… More > Graphic Abstract

Baraket Nada^1,2,3,*, Brandelet Benoit¹, Trouvé Gwenaëlle², Rogaume Yann¹

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1419-1425, 2022, DOI:10.32604/fdmp.2022.021753 - 27 May 2022

Abstract One option to fight global warming is to convert our use of fossil energy into renewables such as biomass energy. However, the forest preservation and the quality of the ambient air are also two major issues. Therefore, the use of biomass waste without any supplementary emissions could represent a part of the solution. In this study, two fuels were considered for a 200 kW moving grate boiler. A multicyclone and a bag filter were fitted on the boiler. The first fuel consisted of classical wood chips whereas the second was a mixture of wood chips… More >

Saad Adjal^1,*, Sabiha Aklouche-Benouaguef¹, Belkacem Zeghmati²

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1389-1397, 2022, DOI:10.32604/fdmp.2022.021619 - 27 May 2022

Abstract Two-dimensional transient laminar natural convection in a square cavity containing a porous medium and inclined at an angle of 30∘ is investigated numerically. The vertical walls are differentially heated, and the horizontal walls are adiabatic. The effect of Rayleigh number on heat transfer and on the road to chaos is analyzed. The natural heat transfer and the Darcy Brinkman equations are solved by using a finite volume method and a Tri Diagonal Matrix Algorithm (TDMA). The results are obtained for a porosity equal to 0.45, a Darcy number and a Prandtl respectively equal to 10⁻³ and More >

Mourad Najjaoui^1,*, Thami Ait-Taleb¹, Abdelhalim Abdelbaki², Zaki Zrikem², Hassan Chaib¹

FDMP-Fluid Dynamics & Materials Processing, Vol.18, No.5, pp. 1339-1348, 2022, DOI:10.32604/fdmp.2022.021564 - 27 May 2022

Abstract In this paper, some effort is provided to optimize the geometry of a concrete hollow brick (used in the construction of building roofs) in order to increase the related thermal resistance, thereby reducing energy consumption. The analysis is conducted for three different configurations of the hollow concrete bricks. Coupling of conduction, natural convection and thermal radiation phenomena is considered. Moreover, the flows are assumed to be laminar and two-dimensional for the whole range of parameters examined. The conservation equations are solved by a finite difference method based on the control volumes approach and the SIMPLE More >