Le-Le Zhang¹, Xue-Qian Fang¹, Jin-Xi Liu¹, Ji-Hong Ma¹

CMC-Computers, Materials & Continua, Vol.21, No.3, pp. 171-186, 2011, DOI:10.3970/cmc.2011.021.171

Abstract On the basis of continuum surface elasticity, two interacting cylindrical nano-inhomogeneities with surface/interface effect in a small-sized solid under anti-plane shear waves are investigated, and the dynamic stress around the nano-inhomogeneities is analyzed. The wave function expansion method is used to expressed the wave field around the two nano-inhomogeneities. The total wave field is obtained by the addition theorem for cylindrical wave function. Through analysis, it is found that the distance between the two nano-inhomogeneities shows great effect on the dynamic stress in nano composites. The effect of the distance is also related to the properties of the nano-inhomogeneities and… More >

W.H. Chen¹, C.W. Hong^1,2

CMC-Computers, Materials & Continua, Vol.21, No.2, pp. 147-170, 2011, DOI:10.3970/cmc.2011.021.147

Abstract Nanorod/nanowell/nanotube arrays are effective nanotechnologies that can increase the performance of a photo-electrochemical solar cell by increasing the reaction area of the working electrode. However, the confined space due to the nano-arrays also tends to decrease the redox ion diffusivity. This paper describes computer modeling on the ionic diffusion of the active species (I-/I3-) among the nano-arrays of the working electrode material (TiO2). A three dimensional periodic boundary molecular dynamics simulation technique is employed to simulate the nano-scale transport phenomenon. Performance improvement tendency can be evaluated from the Butler-Volmer equation. Simulation results reveal that the increasing reaction area times the… More >

Bin Li¹, Guo-biao Yang¹, Qi-rong Zhu², Fan Ni²

CMC-Computers, Materials & Continua, Vol.21, No.2, pp. 107-118, 2011, DOI:10.3970/cmc.2011.021.107

Abstract In this paper, digital image correlation method (DICM) is employed to measure the shear behavior of the spot welding specimens and the ones using adhesive under quasi-static lap shear testing. The images of the specimens' surfaces are captured in real-time by CCD and corresponding computer system. DICM is subsequently used to obtained strain by correlating the images captured before and after deformation. Then, both force-displacement curves and stress-strain curves of the specimens including the cracking load are obtained. The results and analysis show that the mechanical properties of specimens using adhesive compared with the spot welding specimens have an obvious… More >

Chih-Wen Chang¹

CMC-Computers, Materials & Continua, Vol.21, No.2, pp. 87-106, 2011, DOI:10.3970/cmc.2011.021.087

Abstract We address a new numerical approach to deal with these multi-dimensional backward wave problems (BWPs) in this study. A fictitious time τ is utilized to transform the dependent variable u(x, y, z, t) into a new one by (1+τ)u(x, y, z, t)=: v(x, y, z, t, τ), such that the original wave equation is written as a new hyperbolic type partial differential equation in the space of (x, y, z, t, τ). Besides, a fictitious viscous damping coefficient can be employed to strengthen the stability of numerical integration of the discretized equations by using a group preserving scheme. Several numerical… More >

S. H. Kwon¹, B. R. Kim², H. K. Lee^2,3

CMC-Computers, Materials & Continua, Vol.21, No.1, pp. 65-86, 2011, DOI:10.3970/cmc.2011.021.065

Abstract The electromagnetic shielding effectiveness of grid-mesh films made of polyaniline was numerically investigated, and the optimal size of the polyaniline grid was determined through numerical analyses. The permittivity of polyaniline was first determined from an inverse analysis based on experimental data. A series of numerical analyses were carried out with 225 polyaniline grid-mesh films of different thickness, spacing, and width, and the shielding effectiveness of every grid was examined. In addition to the numerical analysis, the transparency of the grid-mesh films and the amount of polyaniline material required to manufacture the unit grid area (1mx1m) were calculated. The optimal dimensions… More >

Chein-Shan Liu¹

CMC-Computers, Materials & Continua, Vol.21, No.1, pp. 17-40, 2011, DOI:10.3970/cmc.2011.021.017

Abstract Only the left-boundary data of temperature and heat flux are used to estimate an unknown parameter function α(x) in T_t(x,t) = ∂(α(x)T_x)/∂x + h(x,t), as well as to recover the right-boundary data. When α(x) is given the above problem is a well-known inverse heat conduction problem (IHCP). This paper solves a mixed-type inverse problem as a combination of the IHCP and the problem of parameter identification, without needing to assume a function form of α(x) a priori, and without measuring extra data as those used by other methods. We use the one-step Lie-Group Adaptive Method (LGAM) for the semi-discretizations of… More >

V.G.Yakhno¹

CMC-Computers, Materials & Continua, Vol.21, No.1, pp. 1-16, 2011, DOI:10.3970/cmc.2011.021.001

Abstract Homogeneous non-dispersive anisotropic materials, characterized by a positive constant permeability and a symmetric positive definite conductivity tensor, are considered in the paper. In these anisotropic materials, the electric and magnetic dyadic Green's functions are defined as electric and magnetic fields arising from impulsive current dipoles and satisfying the time-dependent Maxwell's equations in quasi-static approximation. A new method of deriving these dyadic Green's functions is suggested in the paper. This method consists of several steps: equations for electric and magnetic dyadic Green's functions are written in terms of the Fourier modes; explicit formulae for the Fourier modes of dyadic Green's functions… More >

X. H. Du¹, X. P. Shen¹

CMC-Computers, Materials & Continua, Vol.20, No.3, pp. 225-242, 2010, DOI:10.3970/cmc.2010.020.225

Abstract Aim of this paper is to estimate the integrity of liquefied natural gas (LNG) prestressed storage tank under seismic influence. The coupled Eulerian-Lagrangian (CEL) analysis technique is used to simulate the fluid-structure interaction between LNG and the cylinder of LNG prestressed storage tank. The 3-D model of LNG has been dispersed by Eulerian mesh that is different from traditional analysis method which is called the added mass method. Meanwhile, both of the 3-D models of prestressed rebar and concrete structure are dispersed by Lagrangian mesh. Following conclusions are obtained: 1) Natural frequency of the whole model has been obtained by… More >

X.P. Shen, A. Diaz¹, T. Sheehy²

CMC-Computers, Materials & Continua, Vol.20, No.3, pp. 205-224, 2010, DOI:10.3970/cmc.2010.020.205

Abstract This paper presents a case study for the design of a mud-weight window (MWW) with three-dimensional (3-D), finite-element (FE) tools for subsalt wells. The trajectory of the target well penetrates a 7 km thick salt body. A numerical scheme has been proposed for calculating the shear failure gradient (SFG) and fracture gradient (FG) with 3-D FE software. User subroutines have been developed to address non-uniform pore-pressure distribution. A series of FE calculations were performed to obtain the MWW of the target wellbore, which consists of the SFG and FG for the subsalt sections. Although no reverse faulting structure exists in… More >

X.P. Shen¹, J.L. Feng²

CMC-Computers, Materials & Continua, Vol.20, No.2, pp. 185-204, 2010, DOI:10.3970/cmc.2010.020.185

Abstract The characteristic length of a gradient-dependent damage model is a key parameter, which is usually regarded as the length of damage process zone (DPZ). Value and evolution of the size of DPZ were investigated by both a numerical method and an experimental manner. In the numerical study, the geometrical model adopted was a set of four-point shearing beams; the numerical tool used was the Abaqus/Explicit software. The distance between the front and end of a complete DPZ was obtained. Values of strain components at these points were given out at given time points. The experimental study of the evolution process… More >