Kentaro Doi^1,2, Yuzuru Chikasako¹, Satoyuki Kawano^1,3

FDMP-Fluid Dynamics & Materials Processing, Vol.11, No.1, pp. 1-26, 2015, DOI:10.3970/fdmp.2015.011.001

Abstract Propylene carbonate (PC) and ethylene carbonate are known as good candidates of organic solvents to be used in Li-ion rechargeable batteries, since Li⁺ ions exhibit preferable charge-discharge characteristics with such solvents. On the other hand, polar solvents usually form solvation shells with solute ions, and cause a drastic reduction of ionic conductivity. Along these lines, there has been a curious question why the diffusion coefficient D_Li of Li⁺ strongly depends on the salt concentration. In the present study, a theoretical model is developed on the basis of the Langevin equation in which the interactions between ions and solvent molecules are… More >

Munther Issa K,ah¹, Jean-Luc Meunier²

FDMP-Fluid Dynamics & Materials Processing, Vol.5, No.2, pp. 123-136, 2009, DOI:10.3970/fdmp.2009.005.123

Abstract Multi walled carbon nanotubes (MWCNTs) were synthesized on different graphite types covered with thin layer of nickel catalyst by catalytic chemical vapour deposition using acetylene as hydrocarbon source. The produced carbon nanotubes were investigated by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and transmission electron microscopy (TEM). The shape, quantity and diameter of the MWCNTs are shown to be affected by the type of the graphite substrate, the growth temperature and the hydrocarbon source flow rate. The diameters of the produced MWCNTs were ranged between 43 and 80 nm for pyrolytic (PYROID) and polycrystalline (AXF-5Q) graphite, respectively when the… More >

Munther Issa K,ah¹, Jean-Luc Meunier²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.4, pp. 231-236, 2008, DOI:10.3970/fdmp.2008.004.231

Abstract Multi-walled carbon nanotubes (MWCNTs) have been produced by chemical vapor deposition using acetylene as a hydrocarbon source at 700 \textdegree C. The Monel substrates coated with MWCNTs can be used later as cathodes in the Physical Vapor Deposition (PVD) systems to produce CNTs embedded in diamond-like carbon (DLC) film. This new method of generating MWCNTs on Monel substrates without using any catalyst is very simple and uses very little power compared to other CNTs generating techniques. Embedded CNTs in a crystalline carbon coat was observed on mirror-like polished Monel substrates at 700 \textdegree C but not on the rough Monel… More >

T. J Jaber¹, M. Khawaja¹, M.Z. Saghir¹

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.4, pp. 271-286, 2006, DOI:10.3970/fdmp.2006.002.271

Abstract This paper numerically investigates the interaction between thermodiffuion and buoyancy driven convection in a laterally heated vertical porous cavity for different permeability. The Firoozabadi model is applied to binary hydrocarbon mixtures: (i) the mixture of 1,2,3,4 tetrahydronaphtalene (THN) and dodecane (C12) with mass fraction of 50% for each component, (ii) 1,2,3,4 tetrahydronaphtalene and isobutylbenzene (IBB) with mass fraction of 50% for each component, and (iii) isobutylbenzene and dodecane with mass fraction of 50% for each component. The thermal and molecular diffusion coefficients, which are functions of the temperature and other properties of mixture, are calculated at each point of the… More >

Huanchun Chen¹, Kunigal Shivakumar¹

CMC-Computers, Materials & Continua, Vol.8, No.1, pp. 33-42, 2008, DOI:10.3970/cmc.2008.008.033

Abstract Thermal cycling degradation effect on tensile and flexural properties of Cytec T650 carbon/Lonza Primaset PT-30 cyanate ester composite rods used for gas turbine engine brush seals was evaluated. The composite rods were thermal cycled in air from room temperature to 315°C for 100, 200, 400, 600 and 800 cycles. Each thermal cycle is a one hour period with 28 minutes hold at peak temperature and a high heating/cooling rate of 73°C/min. The composite withstood the first 100 thermal cycles with less than 10% property change. After that, tensile strength and fracture strain as well as flexural modulus were gradually reduced.… More >

Arnab Chakrabarty¹, Tahir Çağin¹

CMC-Computers, Materials & Continua, Vol.7, No.3, pp. 167-190, 2008, DOI:10.3970/cmc.2008.007.167

Abstract The excellent set of properties of carbon nanotube and carbon nanotube-based nanostructures has been established by various studies. However the claimed property values and trends have not been unanimously agreed upon. Using state of the art molecular dynamics and ab initio methods, we have extensively studied the mechanical, thermal and structural properties of carbon nanotubes and carbon nanotube based nanostructures. Additionally this study aims to address the approaches used in various studies to assess the validity and influence of various definitions used for determining the physical properties as reported in earlier experiments and theoretical calculations. We have come up with… More >

G. Q. Xie^1,2,3, X. Han², S. Y. Long³

CMC-Computers, Materials & Continua, Vol.6, No.1, pp. 1-12, 2007, DOI:10.3970/cmc.2007.006.001

Abstract A multi-walled carbon nanotube is modeled as a multiple-elastic cylindrical structure. The numerical-analytical method is adopted to analyze the characteristics of harmonic waves propagating along an anisotropic carbon nanotube. Each wall of the carbon nanotube is divided into three-nodal-line layer elements. The deflections of two adjacent tubes are coupled through the van der Waals. The governing equation of element is obtained from Hamilton's principle. A set of system equation of dynamics equilibrium for the entire structure is obtained by the assembling of all the elements. From solution of the eigenvalue equations, the dispersive characteristics, group velocities of multi-walled carbon nanotubes… More >

G. Q. Xie^1,2, S. Y. Long^1,3

CMC-Computers, Materials & Continua, Vol.4, No.1, pp. 11-20, 2006, DOI:10.3970/cmc.2006.004.011

Abstract The concept of the micropolar theory is employed to investigate vibration behaviors of carbon nanotubes. The constitutive relation has been deduced from the two-dimensional analysis of the microstructure of the carbon nanotube. Van der Waals interactions are simulated by a weak spring model. Hamilton's principle is employed to obtain dynamics equations of the multi-walled carbon nanotube. Numerical examples for both single-walled and double-walled carbon nanotubes are presented and the significant difference in vibration behaviors between them has been distinguished. Numerical results show that fundamental frequencies for the cantilever single-walled carbon nanotube decreases with increase of the aspect ratio of them,… More >

Puneet Kumar^1,*, J. Srinivas²

CMC-Computers, Materials & Continua, Vol.54, No.1, pp. 1-20, 2018, DOI:10.3970/cmc.2018.054.001

Abstract Evolution of computational modeling and simulation has given more emphasis on the research activities related to carbon nanotube (CNT) reinforced polymer composites recently. This paper presents the composite cylinder assemblage (CCA) approach based on continuum mechanics for investigating the elastic properties of a polymer resin reinforced by multi-walled carbon nanotubes (MWCNTs). A three-phase cylindrical representative volume element (RVE) model is employed based on CCA technique to elucidate the effects of inter layers, chirality, interspacing, volume fraction of MWCNT, interphase properties and temperature conditions on the elastic modulus of the composite. The interface region between CNT and polymer matrix is modeled… More >

J. Joseph¹, Y. C. Lu ¹,

CMC-Computers, Materials & Continua, Vol.42, No.1, pp. 63-74, 2014, DOI:10.3970/cmc.2014.042.063

Abstract The super-long, vertically aligned carbon nanotubes (SL-VACNTs) are novel carbon nanomaterial produced from template-free synthesis. The mechanical responses of such material have been investigated by continuum finite element modeling and compared with experimental observations. The crushable foam model has been adequate in modeling the stress-strain curve and deformation of the SL-VACNTs under compression. SL-VACNTs are seen to exhibit transient elastic deformation at small displacement and then plastic deformation at large displacement. The deformation mostly occur at the position immediately beneath the compression platen (indenter face) due to the high stress/strain concentrations. More >