Nour El Houda Ben Mustaphaa^1,3,*, Ibtissem Boumnijel¹, M. El-Ganaoui², Daoued Mihoubi¹

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.6, pp. 1339-1348, 2023, DOI:10.32604/fdmp.2023.022888

Abstract Drying of a deformable saturated porous medium based on convective tempering is a novel method that can enhance energy efficiency and the quality of the dried product itself. In this experimental investigation, the performances of this specific technique are compared with those of a standard stationary drying process in terms of deformation, drying kinetics, moisture redistribution, and energy consumption. In particular, the response of a deformable saturated porous medium (Kaolin) is considered. The results are critically discussed pointing out advantages and drawbacks. More > Graphic Abstract

Marwa El Yassi^1,2,*, Ikram El Abbassi^1,2, Alexandre Pierre², Yannick Melinge³

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.5, pp. 1283-1290, 2023, DOI:10.32604/fdmp.2022.023183

Abstract Phase change materials (PCMs) have the ability to store thermal energy and make it available at a later stage to keep indoor temperature within a specific range and achieve better thermal comfort in buildings. This study focuses on the performances of materials obtained by combining a standard building material with a PCM. In particular, two different materials mixed with the same PCM are considered under the same climatic conditions. The related thermal behavior is assessed in the framework of numerical simulations conducted with ANSYS Fluent assuming parameters representative of a city located in Europe. The results show that the addition… More >

Yanfeng Zhu¹, Huidong Shi¹, Qing Ju¹, Dong Zhao¹, Yucai Shen^1,2,*, Tingwei Wang^1,2,*

Journal of Renewable Materials, Vol.11, No.3, pp. 1303-1319, 2023, DOI:10.32604/jrm.2022.023129

Abstract Poly(butylene adipate-co-terephthalate) (PBAT) and poly(butylene succinate-co-adipate) (PBSA) blend films were prepared with different contents of a multifunctional epoxide chain extender Joncryl ADR-4468 (ADR) or benzoyl peroxide (BPO). The long-chain-branching (LCB) introduced by ADR and branched/crosslinked entanglement induced by BPO increased melt elasticity, viscosity and compatibility, as indicated by thermal properties, rheological and morphological analyses. It was found that the elongation at break and the tensile strength were significantly improved, due to the enhancement of compatibility and the interfacial adhesion by the incorporation of ADR or BPO. The best mechanical properties were obtained in PBAT/PBSA/ADR (60/40/0.3) (A4T6A_0.3) and PBAT/PBSA/BPO (60/40/0.9) (A4T6B_0.9)… More > Graphic Abstract

Pengfei Guan¹, Ping Li², Yiqiang Wu¹, Xingong Li¹, Guangming Yuan¹, Yingfeng Zuo^1,*

Journal of Renewable Materials, Vol.10, No.9, pp. 2451-2463, 2022, DOI:10.32604/jrm.2022.020459

Abstract To enhance mechanical properties and improve flame retardancy and smoke suppression of fast-growing poplar wood in wood applications, the wood was impregnated and modified. An organic phenolic prepolymer and inorganic sodium silicate was used as contrasting impregnation modifiers and wood samples were impregnated by a bionic “respiration” method with alternating positive and negative pressure. The weight percentage gain, density increase ratio, mechanical properties (bending and compressive strength and hardness), and water absorption rate of inorganic and organic-impregnated modified poplar wood (IIMPW and OIMPW, respectively) were compared and these properties in IIMPW were found to be higher than those of OIMPW… More >

Mohammad Alkhedher^*

CMC-Computers, Materials & Continua, Vol.72, No.1, pp. 1901-1920, 2022, DOI:10.32604/cmc.2022.025334

Abstract Modern fighters are designed to fly at high angle of attacks reaching 90 deg as part of their routine maneuvers. These maneuvers generate complex nonlinear and unsteady aerodynamic loading. In this study, different aerodynamic prediction tools are investigated to achieve a model which is highly accurate, less computational, and provides a stable prediction of associated unsteady aerodynamics that results from high angle of attack maneuvers. These prediction tools include Artificial Neural Networks (ANN) model, Adaptive Neuro Fuzzy Logic Inference System (ANFIS), Fourier model, and Polynomial Classifier Networks (PCN). The main aim of the prediction model is to estimate the pitch… More >

Songlin Yang^1,2, Xingjin Han^1,2, Chufeng Kuang^1,2, Weihua Fang³, Jianfei Zhang⁴, Tiantang Yu^4,*

CMES-Computer Modeling in Engineering & Sciences, Vol.131, No.1, pp. 49-72, 2022, DOI:10.32604/cmes.2022.018325

Abstract The deformation prediction models of Wuqiangxi concrete gravity dam are developed, including two statistical models and a deep learning model. In the statistical models, the reliable monitoring data are firstly determined with Lahitte criterion; then, the stepwise regression and partial least squares regression models for deformation prediction of concrete gravity dam are constructed in terms of the reliable monitoring data, and the factors of water pressure, temperature and time effect are considered in the models; finally, according to the monitoring data from 2006 to 2020 of five typical measuring points including J₂₃ (on dam section ), J₃₃ (on dam section… More >

Mohammad Anwar-Us-Saadat¹, Janeshka Goonewardena², Bidur Kafle², Mahmud Ashraf^2,*, Mahbube Subhani²

Journal of Renewable Materials, Vol.10, No.6, pp. 1575-1606, 2022, DOI:10.32604/jrm.2022.018919

Abstract Cross laminated timber (CLT) is an innovative and environment friendly engineered timber product with superior structural performance. CLT offers strong resistance against both in-plane and out-of-plane loading. Hence, it is widely used as floors, roofs or wall elements. Considerable experimental research on CLT under various loading conditions has been done in the recent past. This article presents a comprehensive review of various design methods to determine basic mechanical properties such as tension, compression and rolling shear strength of CLT with primary focus on Norway spruce. All relevant experimental data available from existing literature were collated and consequently been used to… More >

Gang He^*

Molecular & Cellular Biomechanics, Vol.19, No.1, pp. 41-50, 2022, DOI:10.32604/mcb.2022.017044

Abstract This study aims to analyze the biomechanical difference between the two legs of male badminton players when they land on one leg, thereby providing some guidance for preventing sports injury. Ten male badminton players were selected as the subjects. They did the single-leg landing movement successfully three times. The kinematic data were obtained by the Vicon infrared high-speed motion capture system. The kinetic data were obtained by the KISTLER three-dimensional forcing measuring platform. The data were processed and analyzed. The center of gravity of the right leg on the X and Y axes were 0.25 ± 0.05 and 0.21 ± 0.04 m, respectively, which were… More >

Kuntha Pin¹, Jee Ho Chang², Yunyoung Nam^3,*

CMC-Computers, Materials & Continua, Vol.70, No.3, pp. 5821-5834, 2022, DOI:10.32604/cmc.2022.021943

Abstract While the usage of digital ocular fundus image has been widespread in ophthalmology practice, the interpretation of the image has been still on the hands of the ophthalmologists which are quite costly. We explored a robust deep learning system that detects three major ocular diseases: diabetic retinopathy (DR), glaucoma (GLC), and age-related macular degeneration (AMD). The proposed method is composed of two steps. First, an initial quality evaluation in the classification system is proposed to filter out poor-quality images to enhance its performance, a technique that has not been explored previously. Second, the transfer learning technique is used with various… More >

Yen Liang Tung¹, Zubair Ahmad², Eisa Mahmoudi^2,*

Computer Systems Science and Engineering, Vol.39, No.3, pp. 351-363, 2021, DOI:10.32604/csse.2021.014270

Abstract The heavy-tailed distributions are very useful and play a major role in actuary and financial management problems. Actuaries are often searching for such distributions to provide the best fit to financial and economic data sets. In the current study, a prominent method to generate new distributions useful for modeling heavy-tailed data is considered. The proposed family is introduced using trigonometric function and can be named as the Arcsine-X family of distributions. For the purposes of the demonstration, a specific sub-model of the proposed family, called the Arcsine-Weibull distribution is considered. The maximum likelihood estimation method is adopted for estimating the… More >