Fatima Ezzahra El Abbassi^1,*, Mustapha Assarar², Rezak Ayad², Hamid Sabhi², Stephane Buet², Nouzha Lamdouar³

Journal of Renewable Materials, Vol.7, No.3, pp. 253-267, 2019, DOI:10.32604/jrm.2019.01759

Abstract This paper aims at studying the effect of recycling on the static and dynamic properties of short alfa fibre reinforced polypropylene. For this purpose, alfa fibres reinforced composites were elaborated by an injection moulding process and were subjected to different mechanical recycling cycles. Then, non-recycled and recycled materials were subjected to static tests and Dynamic Mechanical Analysis (DMA) to evaluate the effect of recycling on their behaviour. Besides, the effects of alkali and salt water treatments on the static and dynamic properties of the alfa composite were also investigated. The obtained results show that tensile and flexural properties of alfa… More >

Hynek Beneš, Aleksandra Paruzel*, Jiří Hodan and Olga Trhlíková

Journal of Renewable Materials, Vol.6, No.7, pp. 697-706, 2018, DOI:10.32604/JRM.2018.00011

Abstract In this study, castor oil, rapeseed oil and medium chain triglycerides of coconut oil, were transesterified by means of 2-ethyl-2-hydroxymethyl-1,3-propanediol (trimethylolpropane) and consequently used to convert polycarbonate waste from end-of-life vehicles into liquid polyols. The prepared recycled polyols, composed uniquely of renewable and recycled components, had a hydroxyl number of ca. 250 mg KOH·g−1. They were successfully applied as 100% replacement of a virgin polyol for preparation of solid crosslinked polyurethanes (PU) by solvent-free casting. The produced rigid cast PU exhibited the main transition temperature ranging from 44°C to 53°C, the hardness value from 46 to 61 Shore D and… More >

O. Gil-Castell¹, J. D. Badia^1,2, A. Ribes-Greus^1,*

Journal of Renewable Materials, Vol.6, No.4, pp. 370-382, 2018, DOI:10.7569/JRM.2017.634170

Abstract A blending strategy of virgin and reprocessed polylactide may be postulated as an alternative to reduce the material cost at industrial level, and as a valorization route to plastic waste management of production scraps. The performance of blends prepared from virgin polylactide and polylactide mechanically reprocessed up to two cycles (PLA-V/R) was assessed in terms of thermo-oxidative stability, morphology, viscoelasticity and thermal kinetics for energetic valorization. PLA-V/R blends showed appropriate thermo-oxidative stability. The amorphous nature of polylactide was preserved after blending. The viscoelastic properties showed an increment of the mechanical blend effectiveness, which suggested the feasibility of using PLA-V/R blends… More >

Yanxia Wang¹, Yu Wang², Siqi Li³, ur Rehman Aziz³, Shutian Liu¹, Kairong Qin^2,*

CMES-Computer Modeling in Engineering & Sciences, Vol.116, No.2, pp. 127-147, 2018, DOI: 10.31614/cmes.2018.03985

Abstract Assessment of the magnitude and pattern of wall shear stress (WSS) in vivo is the prerequisite for studying the quantitative relationship between exercise-induced WSS and arterial endothelial function. In the previous studies, the calculation of the WSS modulated by exercise training was primarily based upon the rigid tube model, which did not take non-linear effects of vessel elastic deformation into consideration. In this study, with an elastic tube model, we estimated the effect of a bout of 30-minute acute cycling exercise on the WSS and the flow rate in the common carotid artery according to the measured inner diameter, center-line… More >

Yasunori Yusa¹, Shinobu Yoshimura¹

CMES-Computer Modeling in Engineering & Sciences, Vol.99, No.1, pp. 87-104, 2014, DOI:10.3970/cmes.2014.099.087

Abstract To speed up the elastic–plastic analysis of a large-scale model with a crack in which plasticity is observed near the crack, the partitioned coupling method is applied. In this method, the entire analysis model is decomposed into two non-overlapped domains (i.e., global and local domains), and the two domains are analyzed with an iterative method. The cracked local domain is modeled as an elastic–plastic body, whereas the large-scale global domain is modeled as an elastic body. A subcycling technique is utilized for incremental analysis to reduce the number of global elastic analyses. For a benchmark problem with 6 million degrees… More >

Huanchun Chen¹, Kunigal Shivakumar¹

CMC-Computers, Materials & Continua, Vol.8, No.1, pp. 33-42, 2008, DOI:10.3970/cmc.2008.008.033

Abstract Thermal cycling degradation effect on tensile and flexural properties of Cytec T650 carbon/Lonza Primaset PT-30 cyanate ester composite rods used for gas turbine engine brush seals was evaluated. The composite rods were thermal cycled in air from room temperature to 315°C for 100, 200, 400, 600 and 800 cycles. Each thermal cycle is a one hour period with 28 minutes hold at peak temperature and a high heating/cooling rate of 73°C/min. The composite withstood the first 100 thermal cycles with less than 10% property change. After that, tensile strength and fracture strain as well as flexural modulus were gradually reduced.… More >