K. S. Alan¹

CMC-Computers, Materials & Continua, Vol.44, No.1, pp. 1-21, 2014, DOI:10.3970/cmc.2014.044.001

Abstract In the framework of the piecewise homogeneous body model with the use of the three-dimensional geometrically nonlinear exact equations of the theory of elasticity, the method developed for the determination of the stress distribution in the nanocomposites with unidirectional locally curved and hollow nanofibers is used to investigate the normal stresses acting along the nanofibers. Furthermore, it is assumed that the body is loaded at infinity by uniformly distributed normal forces which act along the nanofibers and the crosssection of the nanofibers and normal to its axial line, is a circle of constant radius along the entire nanofiber length. For… More >

H. Jiang^1,2, B. Yang¹, S. Liu³

CMC-Computers, Materials & Continua, Vol.38, No.2, pp. 61-77, 2013, DOI:10.3970/cmc.2013.038.061

Abstract Actin, fibrin and collagen fiber networks are typical hierarchical biological materials formed by bundling fibrils into fibers and branching/adjoining fibers into networks. The bundled fibrils interact with each other through weak van der Waals forces and, in some cases, additional spotted covalent crosslinks. In the present work, we apply Timoshenko's beam theory that takes into account the effect of transverse shear between fibrils in each bundle to study the overall mechanical behaviors of such fiber networks. Previous experimental studies suggested that these fibers are initially loose bundles. Based on the evidence, it is hypothesized that the fibers undergo transitions from… More >

Huanchun Chen¹, Kunigal Shivakumar¹

CMC-Computers, Materials & Continua, Vol.8, No.1, pp. 33-42, 2008, DOI:10.3970/cmc.2008.008.033

Abstract Thermal cycling degradation effect on tensile and flexural properties of Cytec T650 carbon/Lonza Primaset PT-30 cyanate ester composite rods used for gas turbine engine brush seals was evaluated. The composite rods were thermal cycled in air from room temperature to 315°C for 100, 200, 400, 600 and 800 cycles. Each thermal cycle is a one hour period with 28 minutes hold at peak temperature and a high heating/cooling rate of 73°C/min. The composite withstood the first 100 thermal cycles with less than 10% property change. After that, tensile strength and fracture strain as well as flexural modulus were gradually reduced.… More >

R. Han¹, M.S. Ingber¹, H.L. Schreyer¹

CMC-Computers, Materials & Continua, Vol.4, No.3, pp. 163-176, 2006, DOI:10.3970/cmc.2006.004.163

Abstract Decohesion is an important failure mode associated with fiber-reinforced composite materials. Analysis of failure progression at the fiber-matrix interfaces in fiber-reinforced composite materials is considered using a softening decohesion model consistent with thermodynamic concepts. In this model, the initiation of failure is given directly by a failure criterion. Damage is interpreted by the development of a discontinuity of displacement. The formulation describing the potential development of damage is governed by a discrete decohesive constitutive equation. Numerical simulations are performed using the direct boundary element method. Incremental decohesion simulations illustrate the progressive evolution of debonding zones and the propagation of cracks… More >

Zhengong Zhou¹, Shuang Tian^1,2, Jiawei Zhang³

CMC-Computers, Materials & Continua, Vol.52, No.2, pp. 105-121, 2016, DOI:10.3970/cmc.2016.052.105

Abstract The methods of numerical simulation and test are combined to analyze the impact behavior of glass fiber reinforced aluminum alloy laminate (GLARE). A new failure criteria is proposed to obtain the impact failure of GLARE, and combined with material progressive damage method by writing code of LS-DYNA. Low velocity impact test of GLARE is employed to validate the feasibility of the finite element model established. The simulation results have been shown that progressive damage finite element model established is reliable. Through the application of the finite element model established, the delamination of GLARE evolution progress is simulated, various failure modes… More >

Smitha Gopinath^1,2, S. Meenu³, A. Ramach,ra Murthy¹

CMC-Computers, Materials & Continua, Vol.51, No.2, pp. 81-103, 2016, DOI:10.3970/cmc.2016.051.081

Abstract This paper presents experimental and analytical investigations on concrete beams reinforced with basalt fiber reinforced polymer (BFRP) and steel fibers without stirrups. Independent behaviour of BFRP reinforced beams and steel fiber reinforced beams were evaluated and the effect of combining BFRP bars and steel fiber was investigated in detail. It is found that combining steel fibers with BFRP could change the shear failure of BFRP reinforced beam to flexural failure. Further, the existing analytical models were reviewed and compared to predict the shear strength of both FRP reinforced and steel fiber reinforced beams. Based on the review, the appropriate model… More >

Neeraj Dubey¹, Geeta Agnihotri¹

CMC-Computers, Materials & Continua, Vol.45, No.1, pp. 39-56, 2015, DOI:10.3970/cmc.2015.045.039

Abstract In this paper, midrib of coconut palm leaves (MCL) was investigated for the purpose of development of natural fiber reinforced polymer matrix composites. A new natural fiber composite as MCL/polyester is developed by the hand lay-up method, and the material and mechanical properties of the fiber, matrix and composite materials were evaluated. The effect of fiber content on the tensile, flexural, impact, compressive strength and heat distortion temperature (HDT) was investigated. It was found that the MCL fiber had the maximum tensile strength, tensile modulus flexural strength, flexural modulus and Izod impact strength of 177.5MPa, 14.85GPa, 316.04MPa and 23.54GPa, 8.23KJ/m²… More >

Trenton M. Ricks¹, Thomas E. Lacy, Jr.^1,2, Brett A. Bednarcyk³, Steven M.Arnold³, John W. Hutchins¹

CMC-Computers, Materials & Continua, Vol.40, No.2, pp. 99-130, 2014, DOI:10.3970/cmc.2014.040.099

Abstract A multiscale modeling methodology was developed for continuous fiber composites that incorporates a statistical distribution of fiber strengths into coupled multiscale micromechanics/ finite element (FE) analyses. A modified twoparameter Weibull cumulative distribution function, which accounts for the effect of fiber length on the probability of failure, was used to characterize the statistical distribution of fiber strengths. A parametric study using the NASA Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) was performed to assess the effect of variable fiber strengths on local composite failure within a repeating unit cell (RUC) and subsequent global failure. The NASA code FEAMAC… More >

Paria Naghipour¹, Evan J. Pineda², Steven M. Arnold²

CMC-Computers, Materials & Continua, Vol.35, No.1, pp. 17-33, 2013, DOI:10.3970/cmc.2013.035.017

Abstract The micromechanics theory, generalized method of cells (GMC), was employed to simulate the debonding of fiber/matrix interfaces, within a repeating unit cell subjected to global, cyclic loading, utilizing a cyclic crack growth law. Cycle dependent, interfacial debonding was implemented as a new module to the available GMC formulation. The degradation of interfacial stresses with applied load cycles was achieved via progressive evolution of the interfacial compliance A periodic repeating unit cell, representing the fiber/matrix architecture of a composite, was subjected to combined normal and shear loadings, and degradation of the global transverse stress in successive cycles was monitored. The obtained… More >

Xue-Qian Fang^1,2, Ming-Juan Huang¹, Jun-Ying Wu³, Guo-Quan Nie¹, Jin-Xi Liu¹

CMC-Computers, Materials & Continua, Vol.33, No.2, pp. 199-211, 2013, DOI:10.3970/cmc.2013.033.199

Abstract In nanocomposites, coated nano-fibers are often used to obtain good performance, and the high interface-to-volume ratio shows great effect on the macroscopic effective properties of nanocomposites. In this study, the effect of interface energy around the unidirectional coated nanofibers on the effective dynamic effective properties is explicitly addressed by effective medium method and wave function expansion method. The multiple scattering resulting from the series coating nano-fibers is reduced to the problem of one typical nano-fiber in the effective medium. The dynamic effective shear modulus is obtained on the basis of the derived imperfect interface conditions. Analyses show that the effect… More >