R. Abdeljabar¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 217-230, 2011, DOI:10.3970/fdmp.2011.007.217

Abstract In this paper, we discuss a new technique for desalination based on the principles of the Soret effect. In particular, the method stems from the peculiar behavior of the solute in a solution of sodium chloride (i.e. salty water layer) of uniform concentration being less or equal to 5wt% under the effect of an imposed temperature gradient with average temperature equal to 12oC. The Soret coefficient may be positive or negative according to whether the temperature of the solution is above or below 12oC. As two diffusion processes (one parallel to the temperature gradient and the other anti-parallel) can occur… More >

M. N. Noui-Mehidi¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 141-152, 2011, DOI:10.3970/fdmp.2011.007.141

Abstract The present work is concerned with a numerical study of the performance of a conical annular centrifugal contractor through the analysis of the flow properties when the apex angle is changed for different imposed axial flows. The calculations revealed the advantage of using conical annular centrifugal contractors compared to the cylindrical annular centrifuges. The study is conducted by a comparison analysis of the hydrodynamics of fluid flow in both conical and cylindrical contractors where moderate axial flows are imposed. In both systems the outer body is stationary while the inner rotor is maintained at constant speed. The calculations are achieved… More >

M. Kriaa¹, M. El Alami^1,2, M. Najam¹, E. Semma³

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.2, pp. 125-140, 2011, DOI:10.3970/fdmp.2011.007.125

Abstract In this paper a numerical study of natural convection in a two dimensional convergent channel, with or without rectangular block, is carried out. The block is placed at the channel outlet and its thermal conductivity is set equal to that of air. One of channel planes is heated at constant temperature T_H. The other one is maintained cold at T_C < T_H. The governing equations are solved using a finite volume method and the SIMLEC algorithm for the velocity-pressure coupling is used. Special emphasis is given to detail the effect of the block size and Rayleigh number on the dynamics… More >

Yu. Gaponenko¹, I. Ryzhkov², V. Shevtsova³

FDMP-Fluid Dynamics & Materials Processing, Vol.6, No.1, pp. 75-98, 2010, DOI:10.3970/fdmp.2010.006.075

Abstract Gas-liquid flows in annulus are analyzed for fluids in large range of viscosity ratios. The geometry corresponds to a liquid bridge co-axially placed into an outer cylinder with solid walls. The internal core consists of solid rods at the bottom and top, while the central part is a relatively short liquid zone filled with viscous liquid and kept in its position by surface tension. The gas enters into the annular duct and entrains initially quiescent liquid. The flow structures in the liquid and gas are obtained numerically for different shapes of solid rods. Solution for fully developed flow in annulus… More >

O.M.Lavrenteva, Yu. Holenbergand A.Nir¹

FDMP-Fluid Dynamics & Materials Processing, Vol.6, No.1, pp. 41-74, 2010, DOI:10.3970/fdmp.2010.006.041

Abstract A variety of exact analytical solutions describing natural and thermocapillary convection in a horizontal double layer system consisting of Newtonian and Herschel-Bulkley fluids subjected to longitudinal temperature and concentration gradients is constructed. The lower boundary of the system is a solid wall with no-slip, while the upper ones if either a solid wall or a free surface. It was demonstrated that, depending on the governing parameters of the system, viscoplastic layer is entirely yielded or unyielded, or it can be yielded partially, exhibiting up to 5 flowing and quasi-solid layers. The dependence of the flow patterns (appearance and position of… More >

N. Armour¹, S. Dost^1,2

FDMP-Fluid Dynamics & Materials Processing, Vol.5, No.4, pp. 331-344, 2009, DOI:10.3970/fdmp.2009.005.331

Abstract A combined numerical and experimental investigation has been undertaken to explore the benefits of an applied static magnetic field on Silicon transport into a Germanium melt. This work utilized a similar material configuration to that used in the Liquid Phase Diffusion (LPD) and Melt-Replenishment Czochralski (Cz) growth systems. The measured concentration profiles from the samples processed with and without the application of magnetic field showed very similar shape. The amount of silicon transport into the melt is slightly higher in the samples processed under magnetic field, and there is a substantial difference in dissolution interface shape indicating a change in… More >

Thomas Boeck¹, Alexander Nepomnyashchy^2,3, Ilya Simanovskii²

FDMP-Fluid Dynamics & Materials Processing, Vol.4, No.1, pp. 11-20, 2008, DOI:10.3970/fdmp.2008.004.011

Abstract Anticonvection in a two-layer system of mercury and water is studied using three-dimensional direct numerical simulations with a Fourier-Chebyshev spectral method. The two fluid layers have equal thicknesses and are uniformly heated from above. Interface deformations and surface tension gradients are neglected. The quiescent state is replaced by steady hexagons upon increasing the heating from above. We investigate the destabilization of this primary convective pattern in a small and in a large computational domain upon increasing the temperature difference across the two fluid layers. For the large domain the convection cells become disordered at about twice the critical temperature difference… More >

Ehsan Saeedi¹, Shaghayegh Abbasi¹, Karl F. B ¨ohringer¹, Babak A. Parviz¹

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.4, pp. 221-246, 2006, DOI:10.3970/fdmp.2006.002.221

Abstract Self-assembly is emerging as one of the main methods for construction of heterogeneous systems consisting of multiple component types in nano- and micro-scales. The engineered self-assembly used for system integration involves preparation of parts that can recognize and bind to each other or a template, and perfection of procedures that allow for high yield self-assembly of these parts into a system. Capillary forces resultant from molten alloys are attractive candidates for driving such self-assembly processes as they can simultaneously provide electrical and mechanical connections. The basic self-assembly process is reviewed here. Selection of the appropriate alloy, a critical issue in… More >

Sunil Punjabi¹, K. Muralidhar², P. K. Panigrahi²

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.2, pp. 95-106, 2006, DOI:10.3970/fdmp.2006.002.095

Abstract Convection in a differentially heated two-layer system consisting of air and water was studied experimentally, using laser-interferometry. The cavity used for flow visualization was square in cross-section and rectangular in-plan having dimensions of 447 × 32 × 32 mm³. Experiments performed over different layer thicknesses of water filled in a square cross-section cavity, the rest being air, are reported in the present work. The following temperature differences for each layer height were imposed across the hot and the cold walls of the superposed fluid layers: (i) ΔT=10K and (ii)ΔT =18 K. The present study was aimed at understanding the following… More >

M.El-Gammal¹, J.M.Floryan¹

FDMP-Fluid Dynamics & Materials Processing, Vol.2, No.1, pp. 17-26, 2006, DOI:10.3970/fdmp.2006.002.017

Abstract Interface deformation and thermocapillary rupture in a cavity with free upper surface subject to concentrated heating from above is investigated. The dynamics of the process is modulated by placing different amounts of liquid in the cavity. The results determined for large Biot and zero Marangoni numbers show the existence of limit points beyond which steady, continuous interface cannot exist and processes leading to the interface rupture develop. Evolution of the limit point as a function of the mass of the liquid is investigated. The topology of the flow field is found to be qualitatively similar, regardless of whether the cavity… More >