Estefanía Lidón Sánchez-Safont¹, Jennifer González-Ausejo¹, José Gámez-Pérez¹, José María Lagarón², Luis Cabedo^1*

Journal of Renewable Materials, Vol.4, No.2, pp. 123-132, 2016, DOI:10.7569/JRM.2015.634127

Abstract Novel biodegradable composites based on poly(3-hydroxybutirate-co-3-hydroxyvalerate) (PHBV) and different contents of purifi ed alpha-cellulose fi bers (3, 10, 25 and 45%) were prepared by melt blending and characterized. The composites were characterized by scanning electron microscopy (SEM), wide-angle X-ray scattering (WAXS) experiments, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), dynamic mechanic analysis (DMA) and Shore D hardness measurements. Disintegrability under composting conditions was studied according to the ISO 20200 standard. Morphological results showed that high dispersion of the fi bers was achieved during mixing. Good adhesion on the fi ber-matrix interface was also detected by SEM. The addition of low… More >

Mary Isabel Lopretti^1,2*, Natalia Irene Baldyga³, Maria Gonzalez¹, Laura Beatriz Olazabal³, Marina Graciela Torres³, Fernando Resquin⁴, Leonidas Carrasco⁴

Journal of Renewable Materials, Vol.4, No.1, pp. 66-71, 2016, DOI:10.7569/JRM.2015.634133

Abstract Nowadays, there is a great interest in using lignocellulosic materials as substrate for the production of biorefi nery products. Eucalypti are good options to use as crops to obtain different kinds of biofuels and derivatives, since their plantations show high adaptation potential to soil and weather conditions in Uruguay. The basic process steps involved in the obtainment of biorefi nery materials are: pretreatment, hydrolysis, fermentation and products separation. As delignifi cation is an important process to obtain biorefi nery products, in this context the evaluation of the biological (BT) and hydrothermal (TT) pretreatment of different species of Eucaliptus was studied.… More >

Isabel Patrícia Fernandes¹, Mariana Barbosa¹, Joana Soares Amaral², Vera Pinto³, José Luís Rodrigues³, Maria José Ferreira³, Maria Filomena Barreiro^1*

Journal of Renewable Materials, Vol.4, No.1, pp. 47-56, 2016, DOI:10.7569/JRM.2015.634126

Abstract Among the wide variety of materials employed in the manufacture of shoes, thermoplastic polyurethanes (TPUs) are one of the most widely used. Given its widespread use, and associated waste management problems, the development of more biodegradable and evironmentally compatible solutions is needed. In this work, a polyester-based TPU used in the footwear industry for outsoles production was modifi ed by compounding with lignin, starch and cellulose at content of 4% (w/w). The biodegradability was evaluated by using agar plate tests with the fungi Aspergillus niger ATCC16404, the Gram-negative bacteria Pseudomonas aeruginosa ATCC9027 and an association of both (consortium), and soil… More >

Kabir Fardad¹, Bahman Najafi¹, Sina Faizollahzadeh Ardabili¹, Amir Mosavi^2,3, Shahaboddin Shamshirband,^4,5,*, Timon Rabczuk²

CMC-Computers, Materials & Continua, Vol.55, No.3, pp. 381-392, 2018, DOI: 10.3970/cmc.2018.01803

Abstract Glycyrrhiza glabra, Mint, Cuminum cyminum, Lavender and Arctium medicinal are considered as edible plants with therapeutic properties and as medicinal plants in Iran. After extraction process of medicinal plants, residual wastes are not suitable for animal feed and are considered as waste and as an environmental threat. At present there is no proper management of waste of these plants and they are burned or buried. The present study discusses the possibility of biogas production from Glycyrrhiza Glabra Waste (GGW), Mentha Waste (MW), Cuminum Cyminum Waste (CCW), Lavender Waste (LW) and Arctium Waste (AW). 250 g of these plants with TS… More >