Chih-Ping Wu^1,2, Ruei-Yong Jiang¹, Sheng-Yao Tu¹

CMC-Computers, Materials & Continua, Vol.41, No.2, pp. 111-152, 2014, DOI:10.3970/cmc.2014.041.111

Abstract Exact three-dimensional stability and free vibration analyses of simply-supported, multilayered functionally graded material (FGM) circular hollow cylinders and laminated composite ones under axial compression are presented. The material properties of each FGM layer are assumed to obey a power-law distribution of the volume fractions of constituents through the thickness coordinate. The Pagano method, which is based on the principle of virtual displacement and is conventionally used for the analysis of laminated composite structures, is modified to be feasible for the study of multilayered FGM cylinders, in which Reissner's mixed variational theorem, the successive approximation and transfer matrix methods, and the… More >

Y. L. Liu¹, N. Hu², H. Xu³, H. Ning¹, L. K. Wu¹

CMC-Computers, Materials & Continua, Vol.40, No.1, pp. 1-20, 2014, DOI:10.3970/cmc.2014.040.001

Abstract A real-time monitoring technique for local plasticity using Lamb waves was developed. Tensile test of a thin aluminum plate with a circular hole where high stress concentration was induced was conducted to verify this technique. During the tensile test, a series of wave signals passing through the local plastic region were collected using a directional actuator/sensor set to monitor plasticity evolution. A pulse compression technique was used to process the wave signals. With the increase of tensile stress in the specimen, the amplitude changes of S₀ and A₀ modes were obtained and the difference of Lamb wave signals was further… More >

A. T. Rhead¹, T. J. Dodwell¹, R. Butler^1,2

CMC-Computers, Materials & Continua, Vol.35, No.1, pp. 1-16, 2013, DOI:10.3970/cmc.2013.035.001

Abstract When (robotic) Automated Fibre Placement (AFP) is used to manufacture aerospace components with complex three dimensional geometries, gaps between fibre tows can occur. This paper explores the interaction under compressive load of these tow gaps with impact damage. Two coupons with different distributions of tow-gaps were impacted. Results indicated that the area of delamination is smaller for an impact directly over a tow gap where the tow gap is situated close to the non-impact face. Subsequent Compression After Impact (CAI) testing demonstrated that both the formation of sublaminate buckles and subsequent growth of delaminations is inhibited by the presence of… More >

Xiaonan Hou¹, Hong Hu¹, Yanping Liu¹, Vadim Silberschmidt²

CMC-Computers, Materials & Continua, Vol.23, No.2, pp. 119-134, 2011, DOI:10.3970/cmc.2011.023.119

Abstract Compressibility of warp-knitted spacer fabrics is one of their important mechanical properties with regard to many special applications such as body protection, cushion and mattresses. Due to specific structural features of the fabric and a non-linear mechanical behavior of monofilaments, the compression properties of this kind of fabrics are very complicated. Although several studies have been performed to investigate their compression behavior, its mechanism has not well been understood yet. This work is concerned with a study of compression mechanism of a selected warp-knitted spacer fabric with a given sandwich structure. Both experimental and numerical methods are used to study… More >

Lei Bao^1,2, Christophe Schuman¹, Jean-sébastien Lecomte¹, Marie-Jeanne Philippe¹, Xiang Zhao², Liang Zuo², Claude Esling¹

CMC-Computers, Materials & Continua, Vol.15, No.2, pp. 113-128, 2010, DOI:10.3970/cmc.2010.015.113

Abstract The mechanisms of small plastic deformation of titanium (T40) during cold rolling and channel die compression by means of "interrupted in situ" EBSD orientation measurements were studied. These interrupted EBSD orientation measurements allow to determine the rotation flow field which leads to the development of the crystallographic texture during the plastic deformation. Results show that during rolling, tension twins and compression twins occur and various glide systems are activated, the number of grains being larger with twins than with slip traces. In channel die compression, only tension twins are observed in some grains, whereas slip traces can be spotted in… More >