Hong-Hua Dai^1,2, Jeom Kee Paik³, S. N. Atluri²

CMC-Computers, Materials & Continua, Vol.23, No.2, pp. 155-186, 2011, DOI:10.3970/cmc.2011.023.155

Abstract The application of the Galerkin method, using global trial functions which satisfy the boundary conditions, to nonlinear partial differential equations such as those in the von Karman nonlinear plate theory, is well-known. Such an approach using trial function expansions involving multiple basis functions, leads to a highly coupled system of nonlinear algebraic equations (NAEs). The derivation of such a system of NAEs and their direct solutions have hitherto been considered to be formidable tasks. Thus, research in the last 40 years has been focused mainly on the use of local trial functions and the Galerkin method, applied to the piecewise… More >

Hong-Hua Dai^1,2, Jeom Kee Paik³, Satya N. Atluri²

CMC-Computers, Materials & Continua, Vol.23, No.1, pp. 69-100, 2011, DOI:10.3970/cmc.2011.023.069

Abstract In this paper, the global nonlinear Galerkin method is used to perform an accurate and efficient analysis of the large deflection behavior of a simply-supported rectangular plate under combined loads. Through applying the Galerkin method to the governing nonlinear partial differential equations (PDEs) of the plate, we derive a system of coupled third order nonlinear algebraic equations (NAEs). However, the resultant system of NAEs is thought to be hard to tackle because one has to find the one physical solution from among the possible multiple solutions. Therefore, a suitable initial guess is required to lead to the real solution for… More >

Zhao Huiming¹, Dong Zhengzhu¹, Chen Jiarui¹, Yang Min¹

CMC-Computers, Materials & Continua, Vol.21, No.3, pp. 209-216, 2011, DOI:10.3970/cmc.2011.021.209

Abstract The advantages of coupling of a natural boundary element method and a finite element method are introduced. Then we discuss the principle of the direct coupling of NBEM and FEM and its implementation. The comparison of the results between the direct coupling method and FEM proves that the direct coupling method is simple, feasible and valid in practice. More >

Weichung Yeih¹, Chein-Shan Liu², Chung-Lun Kuo³, Satya N. Atluri⁴

CMC-Computers, Materials & Continua, Vol.17, No.3, pp. 275-302, 2010, DOI:10.3970/cmc.2010.017.275

Abstract In this paper, a multiple-source-point boundary-collocation Trefftz method, with characteristic lengths being introduced in the basis functions, is proposed to solve the direct, as well as inverse Cauchy problems of the Laplace equation for a multiply connected domain. When a multiply connected domain with genus p (p>1) is considered, the conventional Trefftz method (T-Trefftz method) will fail since it allows only one source point, but the representation of solution using only one source point is impossible. We propose to relax this constraint by allowing many source points in the formulation. To set up a complete set of basis functions, we… More >

Surkay D. Akbarov^1,2, Resat Kosker³, Yasemen Ucan³

CMC-Computers, Materials & Continua, Vol.17, No.2, pp. 77-102, 2010, DOI:10.3970/cmc.2010.017.077

Abstract In the framework of the piecewise homogeneous body model with the use of the three-dimensional geometrically non-linear exact equations of the theory of elasticity, the method for determination of the stress-strain state in the infinite body containing periodically located row of periodically curved fibers is developed. It is assumed that the midlines of the fibers are in the same plane. With respect to the location of the fibers according to each other the sinphase and antiphase curving cases are considered. Numerical results on the effect of the geometrical non-linearity to the values of the self balanced shear and normal stresses… More >

Dyi-Cheng¹, Syuan-Yi Syong¹

CMC-Computers, Materials & Continua, Vol.13, No.3, pp. 191-200, 2009, DOI:10.3970/cmc.2009.013.191

Abstract Finite element simulations are performed to investigate the plastic deformation behavior of Ti-6Al-4V titanium alloy during its indirect extrusion through a four-hole die. The simulations assume the die, mandrel and container to be rigid bodies and ignore the temperature change induced during the extrusion process. Under various extrusion conditions, the present numerical analysis investigates the effective stress and profile of product at the exit. The relative influences of the friction factors, the temperature of billet and the eccentricity of four-hole displacement are systematically examined. The simulations focus specifically on the effects of the friction factor, billet temperature and eccentricity ratio… More >

Cheng-Hsiu Yang¹, Cheng Chang¹, Chao-An Lin^1,2

CMC-Computers, Materials & Continua, Vol.11, No.3, pp. 209-228, 2009, DOI:10.3970/cmc.2009.011.209

Abstract In the present study, a lattice Boltzmann method based new immersed boundary technique is proposed for simulating two-dimensional viscous incompressible flows interacting with stationary and moving solid boundaries. The lattice Boltzmann method with known force field is used to simulate the flow where the complex geometry is immersed inside the computational domain. This is achieved via direct-momentum forcing on a Cartesian grid by combining "solid-body forcing" at solid nodes and interpolation on neighboring fluid nodes. The proposed method is examined by simulating decaying vortex, 2D flow over an asymmetrically placed cylinder, and in-line oscillating cylinder in a fluid at rest.… More >