Xiao Sun¹, Huifan Huang¹, Yanjuan Zhao^2,*, Lianghuai Tong^3,*, Haibin Lin³, Yuliang Zhang⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.21, No.6, pp. 1261-1298, 2025, DOI:10.32604/fdmp.2025.064329 - 30 June 2025

Abstract The reverse operation of existing centrifugal pumps, commonly referred to as “Pump as Turbine” (PAT), is a key approach for recovering liquid pressure energy. As a type of hydraulic machinery characterized by a simple structure and user-friendly operation, PAT holds significant promise for application in industrial waste energy recovery systems. This paper reviews recent advancements in this field, with a focus on pump type selection, performance prediction, and optimization design. First, the advantages of various prototype pumps, including centrifugal, axial-flow, mixed-flow, screw, and plunger pumps, are examined in specific application scenarios while analyzing their suitability… More >

Yuliang Zhang^1,2,*, Zezhou Yang¹, Lianghuai Tong^3,*, Yanjuan Zhao⁴, Xiaoqi Jia⁵, Anda Han⁶

FDMP-Fluid Dynamics & Materials Processing, Vol.21, No.4, pp. 891-938, 2025, DOI:10.32604/fdmp.2024.059903 - 06 May 2025

Abstract This paper investigates the start-up and shutdown phases of a five-bladed closed-impeller centrifugal pump through experimental analysis, capturing the temporal evolution of its hydraulic performances. The study also predicts the transient characteristics of the pump under non-rated operating conditions to assess the accuracy of various machine learning methods in forecasting its instantaneous performance. Results indicate that the pump’s transient behavior in power-frequency mode markedly differs from that in frequency-conversion mode. Specifically, the power-frequency mode achieves steady-state values faster and exhibits smaller fluctuations before stabilization compared to the other mode. During the start-up phase, as… More >

Xiao Sun¹, Huifan Huang¹, Yuliang Zhang², Lianghuai Tong^3,*, Xiaowei Xu², Xiaoqi Jia⁴, Litao Ou⁵

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.10, pp. 2251-2264, 2024, DOI:10.32604/fdmp.2024.050997 - 23 September 2024

Abstract In order to obtain the transient characteristics of a low-speed centrifugal pump during the start-up and shutdown stages, dedicated experimental tests were conducted with eight different valve opening conditions. The Pearson correlation coefficient was used to reveal the linear correlation between variables. According to the results, the stable rotational speed decreases with increasing valve opening (rotational speed decreases from approximately 1472 to 1453 r/min), while the stable shaft power exhibits an increasing trend (shaft power increases from approximately 0.242 to 0.390 kW). The stable time and zeroing time of each parameter during start-up and shutdown More >

Xiao Sun¹, Jiangbo Tong¹, Yuliang Zhang^2,*, Haibing Cai³, Wen Zhou⁴, Xiaoqi Jia⁵, Litao Ou⁶

FDMP-Fluid Dynamics & Materials Processing, Vol.20, No.4, pp. 725-737, 2024, DOI:10.32604/fdmp.2023.045541 - 28 March 2024

Abstract Centrifugal pumps are widely used in the metallurgy, coal, and building sectors. In order to study the hydraulic characteristics of a closed impeller centrifugal pump during its shutdown in the so-called power frequency and frequency conversion modes, experiments were carried to determine the characteristic evolution of parameters such as speed, inlet and outlet pressure, head, flow rate and shaft power. A quasi-steady-state method was also used to further investigate these transient behaviors. The results show that, compared to the power frequency input, the performance parameter curves for the frequency conversion input are less volatile and More >