S. D. Harris¹, R. Mustata², L. Elliott², D. B. Ingham², D. Lesnic²

CMES-Computer Modeling in Engineering & Sciences, Vol.25, No.2, pp. 69-80, 2008, DOI:10.3970/cmes.2008.025.069

Abstract Two homogeneous anisotropic materials are butted together to form a contact surface within a single composite material (the specimen). An inverse boundary element method (BEM) is developed to determine the components of the hydraulic conductivity tensor of each material and the position of the contact surface. A steady state flow is forced through the specimen by the application of a constant pressure differential on its opposite faces. Experimental measurements (simulated) of pressure and average hydraulic flux at exposed boundaries are then used in a modified least squares functional. This functional minimises the gap between the above measured (simulated) values and… More >

Leevan Ling¹, Tomoya Takeuchi²

CMES-Computer Modeling in Engineering & Sciences, Vol.20, No.2, pp. 99-110, 2007, DOI:10.3970/cmes.2007.020.099

Abstract We aim to identify the unknown source locations in a two-dimensional heat equation from scattered measurements. In [Inverse Problems, 22(4):1289--1305, 2006], we proposed a numerical procedure that identifies the unknown source locations of 2D heat equation solely based on three measurement points. Due to the nonlinearity and complexity of the problem, the quality of the resulting estimations is often poor especially when the number of unknown is large. In this paper, we purpose a linear refinement scheme that takes the outputs of the existing nonlinear algorithm as initial guesses and iteratively improves on the accuracy of the estimations; the convergence… More >

Daiki Shiozawa¹, Shiro Kubo², Takahide Sakagami², Masaaki Takagi²

CMES-Computer Modeling in Engineering & Sciences, Vol.11, No.1, pp. 27-36, 2006, DOI:10.3970/cmes.2006.011.027

Abstract The passive electric potential CT (computed tomography) method using piezoelectric film was applied to the identification of plural through cracks. The use of piezoelectric material made it possible to obtain electric potential field without applying electric current. For identification of cracks an inverse analysis scheme based on the least residual method was applied, in which square sum of residuals is evaluated between the measured electric potential distributions and those computed by using the finite element method. Akaike information criterion (AIC) was used to estimate the number of cracks. Numerical simulations were carried out on the identification of plural cracks and… More >

R Sivaprasad^1,2, S Venkatesha¹, C S Manohar^1,3

CMC-Computers, Materials & Continua, Vol.9, No.3, pp. 179-208, 2009, DOI:10.3970/cmc.2009.009.179

Abstract The problem of identifying parameters of time invariant linear dynamical systems with fractional derivative damping models, based on a spatially incomplete set of measured frequency response functions and experimentally determined eigensolutions, is considered. Methods based on inverse sensitivity analysis of damped eigensolutions and frequency response functions are developed. It is shown that the eigensensitivity method requires the development of derivatives of solutions of an asymmetric generalized eigenvalue problem. Both the first and second order inverse sensitivity analyses are considered. The study demonstrates the successful performance of the identification algorithms developed based on synthetic data on one, two and a 33… More >

Asif Husain¹, M. Guniganti², D. K. Sehgal², R. K. Pandey²

CMC-Computers, Materials & Continua, Vol.8, No.3, pp. 133-150, 2008, DOI:10.3970/cmc.2008.008.133

Abstract This paper describes an approach to identify the mechanical properties i.e. fracture and yield strength of steels. The study involves the FE simulation of shear punch test for various miniature specimens thickness ranging from 0.20mm to 0.80mm for four different steels using ABAQUS code. The experimental method of the miniature shear punch test is used to determine the material response under quasi-static loading. The load vs. displacement curves obtained from the FE simulation miniature disk specimens are compared with the experimental data obtained and found in good agreement. The resulting data from the load vs. displacement diagrams of different steels… More >

Chein-Shan Liu^1,2

CMC-Computers, Materials & Continua, Vol.7, No.2, pp. 81-96, 2008, DOI:10.3970/cmc.2008.007.081

Abstract We consider an inverse problem for estimating an unknown heat conductivity parameter α(t) in a heat conduction equation T_t(x,t) = α(t)T_xx(x,t) with the aid of an extra measurement of temperature gradient on boundary. Basing on an establishment of the one-step Lie-group elements G(r) and G(l) for the semi-discretization of heat conduction equation in time domain, we can derive algebraic equations from G(r) = G(l). The new method, namely the Lie-group estimation method (LGEM), is examined through numerical examples to convince that it is highly accurate and efficient; the maximum estimation error is smaller than 10^-5 for smooth parameter and for… More >

E. Ferretti¹, A. Di Leo¹

CMC-Computers, Materials & Continua, Vol.7, No.2, pp. 59-80, 2008, DOI:10.3970/cmc.2008.007.059

Abstract The main assumption on the basis of the identifying model of the effective law, developed by the Author, is the impossibility of considering the specimen as a continuum, when an identifying procedure from load-displacement to stress-strain in uniaxial compression is attempted. Actually, a failure mechanism with propagation of a macro-crack was found to activate from the very beginning of the uniaxial compression test forth. This leads to considering the acquired displacements as composed by two quotes: one constitutive, due to the material strain, and one of crack opening. Since the ratio between these two quotes is not constant during the… More >

S. Marguet¹, P. Rozycki¹, L. Gornet¹

CMC-Computers, Materials & Continua, Vol.4, No.3, pp. 119-136, 2006, DOI:10.3970/cmc.2006.004.119

Abstract This paper deals with the modelling until rupture of composite structures made of glass-fibre / epoxy-resin woven fabrics submitted to dynamic loadings. The model is built at the mesoscale of the elementary ply. It takes into account the slightly nonlinear brittle behaviour of the fibres under tensile sollicitations, their nonlinear behaviour in compression as well as the strongly non linear and irreversible behaviour of the ply in shear. Strain rate effects are also introduced and special attention is paid to the objectivity of the model in the context of finite element calculation. Therefore the choice of a delayed damage mesomodel… More >

Yue Zhao¹, Jianjian Yue¹, Wei Song^1,*, Xiaona Xu¹, Xiali Li¹, Licheng Wu¹, Qiang Ji²

CMC-Computers, Materials & Continua, Vol.60, No.3, pp. 1223-1235, 2019, DOI:10.32604/cmc.2019.05636

Abstract Tibetan language has very limited resource for conventional automatic speech recognition so far. It lacks of enough data, sub-word unit, lexicons and word inventories for some dialects. And speech content recognition and dialect classification have been treated as two independent tasks and modeled respectively in most prior works. But the two tasks are highly correlated. In this paper, we present a multi-task WaveNet model to perform simultaneous Tibetan multi-dialect speech recognition and dialect identification. It avoids processing the pronunciation dictionary and word segmentation for new dialects, while, in the meantime, allows training speech recognition and dialect identification in a single… More >

Haipeng Chen¹, Kexiong Liu², Chunyang Ma³, Yu Han⁴, Jian Su^5,*

CMC-Computers, Materials & Continua, Vol.57, No.2, pp. 195-204, 2018, DOI:10.32604/cmc.2018.03592

Abstract Recently, object identification with radio frequency identification (RFID) technology is becoming increasingly popular. Identification time is a key performance metric to evaluate the RFID system. The present paper analyzes the deficiencies of the state-of-the-arts algorithms and proposes a novel sub-frame-based algorithm with adaptive frame breaking policy to lower the tag identification time for EPC global C1 Gen2 UHF RFID standard. Through the observation of slot statistics in a sub-frame, the reader estimates the tag quantity and efficiently calculates an optimal frame size to fit the unread tags. Only when the expected average identification time in the calculated frame size is… More >