Mahesh B. Mawale¹, Abhaykumar Kuthe², Padma G. Pawane³, Sandeep W. Dahake²

CMES-Computer Modeling in Engineering & Sciences, Vol.114, No.2, pp. 173-189, 2018, DOI:10.3970/cmes.2018.114.173

Abstract This article describes a study based on the use of an instrumented form of applanation and indentation tonometry through eyelid. The methods and devices which are available for the measurement of intraocular pressure (IOP) have their own limitations. These cause discomfort to the patients during IOP measurement. Also these methods, used to measure IOP over cornea, need anesthesia. In the present work, an attempt is made to develop a device for the measurement of IOP through eyelid which eliminates the need of anesthesia and enhance the patient’s comfort and convenience of the clinician. To represent the results of proposed technique,… More >

F. Wang¹, J.L. Li¹, B.X. Yang¹, N.A. Hill²

CMES-Computer Modeling in Engineering & Sciences, Vol.95, No.1, pp. 59-85, 2013, DOI:10.3970/cmes.2013.095.059

Abstract A gas-liquid two-phase model for the simulation of a power-law fluid mold filling process with the consideration of phase change is proposed, in which the governing equations for the melt and air in the cavity, including the mass conservation, momentum conservation and energy conservation equations, are unified into one system of equation. A revised Enthalpy method, which can be used for both the melt and air in the mold cavity, is proposed to describe the phase change during the mold filling. Finite volume method on non-staggered grid is used to solve the system. The level set method is used to… More >

G. Prater, Jr.¹

CMES-Computer Modeling in Engineering & Sciences, Vol.3, No.3, pp. 299-312, 2002, DOI:10.3970/cmes.2002.003.299

Abstract A vapor compressor's performance is affected by pressure and mass flow fluctuations resulting from acoustic effects in the suction and discharge manifolds. Through proper geometric design of the manifolds, these pulsations can be modified to increase efficiency and reduce noise. This paper documents the development of a computer simulation program used to tune stationary-vane refrigeration compressors. The program models the mechanical, fluid, thermodynamic, kinematic, and acoustical processes occurring in such compressors, and calculates suction and discharge chamber pressures, mass flow rates, valve displacements, and acoustic input and transfer impedances. Experimental acoustic pressure measurements from a refrigerator test stand provide validation… More >

J.H. Wu¹, L.Y. Zhu², J.T. Tang³

CMES-Computer Modeling in Engineering & Sciences, Vol.86, No.3, pp. 225-240, 2012, DOI:10.3970/cmes.2012.086.225

Abstract Magnetic induction hyperthermia is one of hopeful methods for tumor therapy. In this method, several ferromagnetic seeds are needed to be implanted into the tumor. The seeds would produce energy, and cause the nearby tumor to die. Temperature prediction is significant before treatment. In addition, in clinical treatment, the tumor temperature has to be monitored in realtime. However, using as few thermometers as possible is the basic principle. Fortunately, the numerical simulation can contribute to realtime measurement. The seed temperature is modeled based on the Haider's method, which is treated as the thermal boundary in numerical simulation. We employ the… More >

Xiaowei Zeng¹

CMES-Computer Modeling in Engineering & Sciences, Vol.74, No.3&4, pp. 183-202, 2011, DOI:10.3970/cmes.2011.074.183

Abstract This paper presents an atomistic field theory and its application in modeling and simulation of nano/micro materials. Atomistic formulation and finite element implementation of the atomistic field theory is briefly introduced. Numerical simulations based on the field theory are performed to investigate the material behaviors of bcc iron at coarse-grained scale and we have obtained the mechanical strength and elastic modulus, which are in good agreement with results by first principles calculations. Also the nanoscale deformation and failure mechanism are revealed in bcc iron nanorods under simple tension. It is interesting to observe that under tensile loading, iron has gone… More >

Binxin Yang¹, Jie Ouyang¹, Tao Jiang¹, Chuntai Liu²

CMES-Computer Modeling in Engineering & Sciences, Vol.63, No.3, pp. 191-222, 2010, DOI:10.3970/cmes.2010.063.191

Abstract A gas-solid-liquid three-phase model is proposed for fiber reinforced composites mold filling process. The fluid flow is described in Eulerian coordinate while the dynamics of fibers is described in Langrangian coordinate. The interaction of fluid flow and fibers are enclosed in the model. The influence of fluid flow on fibers is described by the resultant forces imposed on fibers and the influence of fibers on fluid flow is described by the momentum exchange source term in the model. A finite volume method coupled with a level set method for viscoelastic-Newtonian fluid flow is used to solve the model. The direct… More >

Robert Rundqvist¹, Andreas Mark¹, Fredrik Edelvik¹, Johan S. Carlsson¹

FDMP-Fluid Dynamics & Materials Processing, Vol.7, No.3, pp. 259-278, 2011, DOI:10.3970/fdmp.2011.007.259

Abstract Multiphase flow simulation using Smoothed Particle Hydrodynamics (SPH) has gained interest during recent years, mostly due to the inherent flexibility of the method and the physically rather intuitive formulation of extra constitutive equations needed when dealing with for instance non-Newtonian flows. In the work presented here, simulations based on an SPH model implemented in the flow solver IBOFlow has been used for simulation of robotic application of sealing material on a car body. Application of sealing materials is done in order to prevent water leakage into cavities of the body, and to reduce noise. In off-line programming of the robots… More >