Orroño DI, RS Lavado^*

Phyton-International Journal of Experimental Botany, Vol.78, pp. 75-82, 2009, DOI:10.32604/phyton.2009.78.075

Abstract Ornamental plants have been proposed for growing in heavy metal (HM) contaminated soils, and also for phytoremediation. We evaluated (1) biomass production and (2) HM accumulation in Pelargonium hortorum. Plants were grown for 16 weeks on HM (cadmium, chromium, copper, lead, nickel and zinc) enriched soils. Treatments were i) control, non-enriched soil, ii) medium concentration treatment, and iii) high concentration treatment. Four destructive harvests were carried out, and roots, stems, leaves, and flowers were analyzed each time. Concentrations of HM were determined using ICP. Significant reductions in biomass production were observed in HM-enriched soils compared with the control. Different indexes… More >

Chan RL

Phyton-International Journal of Experimental Botany, Vol.78, pp. 5-10, 2009, DOI:10.32604/phyton.2009.78.005

Abstract Transcription factors (TFs) are proteins able to specifically recognize DNA sequences in the regulatory regions of their target genes. They bind these specific sequences, an event that leads to the activation or repression of whole signal transduction pathways. In plants about 1500 TFs were informatically identified; identification was mainly based in the presence of DNA-binding domains in the translated sequences. They were classified in families and subfamilies according to several features, including the conservation of the DNA binding domain, the genes structures and the functions they exert. Among transcription factors, several seem to be potential powerful biotechnological tools to improve… More >

Carolina Saint Pierre, Carlos Alberto Busso

Phyton-International Journal of Experimental Botany, Vol.75, pp. 21-30, 2006, DOI:10.32604/phyton.2006.75.021

Abstract This article has no abstract. More >

R. Citarella¹, A. Apicella²

Structural Durability & Health Monitoring, Vol.2, No.3, pp. 183-196, 2006, DOI:10.3970/sdhm.2006.002.183

Abstract This paper presents an overview of the achievements of a research and development project sponsored by the European Commission in the general area of Key Actions and New Perspectives in Aeronautics. The project was coordinated by Alenia and involved partners from major European Aircraft and Helicopter manufactures as well as research institutions and universities. The project was in support of EU policies on energy and environment, in addition to those on transport, economic and social cohesion, industry and, of course, research and technology.
The overall objective of Advanced Design concepts and Maintenance by Integrated risk Evaluation for aerostructures (ADMIRE) was… More >

A. Soprano¹, F. Caputo¹

Structural Durability & Health Monitoring, Vol.2, No.1, pp. 51-68, 2006, DOI:10.3970/sdhm.2006.002.051

Abstract This work describes the results of the experience acquired by the authors during their participation to some among the European research programs with the aim to develop a probabilistic risk assessment procedure to analyse the spreading of fatigue-induced damage in typical aeronautical components. The several steps of the procedure are pointed out, and especially the modelling of the damage evolutionary process; the initiation and the transitional probabilities, which characterize the passage from one damage level to a higher one, are fully characterized and their dependence from time and from the damage state of surrounding zones illustrated by various example results. More >

G. Bertrand¹

Structural Durability & Health Monitoring, Vol.1, No.3, pp. 185-192, 2005, DOI:10.3970/sdhm.2005.001.185

Abstract Each maintenance strategy demands for the definition of an inspection threshold and further inspection intervals. A general criterion for the calculation of the time to first inspection is high probability of detection of a certain crack size and low failure probability in case a predicted crack size was not detected. The proposed method demonstrates that a top down analysis of crack development from critical sizes to detectable sizes reveals an economic benefit with respect to the frequency of inspections. The dispersion of fatigue stress cycles at rupture obtained from component tests at riveted lap joints is transformed to the distribution… More >

S. N. Atluri¹

Structural Durability & Health Monitoring, Vol.1, No.1, pp. 1-20, 2005, DOI:10.3970/sdhm.2005.001.001

Abstract The solution of three-dimensional cracks (arbitrary surfaces of discontinuity) in solids and structures is considered. The BEM, developed based on the symmetric Galerkin BIEs, is used for obtaining the fracture solutions at the arbitrary crack-front. The finite element method is used to model the uncracked global (built-up) structure for obtaining the stresses in an otherwise uncracked body. The solution for the cracked structural component is obtained in an iteration procedure, which alternates between FEM solution for the uncracked body, and the SGBEM solution for the crack in the local finite-sized subdomain. In addition, some crack growth models are used to… More >

Dhouha Belhaj Sghaier¹, Insaf Bankaji¹, Sylvia Pedro², Isabel Caçador², Noomene Sleimi^1,*

Phyton-International Journal of Experimental Botany, Vol.88, No.3, pp. 239-252, 2019, DOI:10.32604/phyton.2019.06887

Abstract The lack of knowledge of plant tolerance and differential response to aluminum (Al) encouraged many researchers, in the last decade, to elucidate Al toxicity and tolerance mechanisms. The current study reported the impact of Al, a toxic element with negative effects on plant growth and development, in halophytic plant Tamarix gallica. Plants were subjected to different Al concentrations (0, 200, 500 and 800 μM) with or without NaCl (200 mM) supplementation. Growth, photosynthesis and mineral content were assessed. Al stress had a significant decrease on shoots’ biomass production between 19 to 41%, and a little variation on chlorophyll content and… More >

Mirza Hasanuzzaman^1,*, Aditya Banerjee², M. H. M. Borhannuddin Bhuyan^3,4, Aryadeep Roychoudhury^2,*, Jubayer Al Mahmud⁵ and Masayuki Fujita³

Phyton-International Journal of Experimental Botany, Vol.88, No.3, pp. 185-221, 2019, DOI:10.32604/phyton.2019.07559

Abstract In the era of climate change, abiotic stresses (e.g., salinity, drought, extreme temperature, flooding, metal/metalloid(s), UV radiation, ozone, etc.) are considered as one of the most complex environmental constraints that restricts crop production worldwide. Introduction of stress-tolerant crop cultivars is the most auspicious way of surviving this constraint, and to produce these types of tolerant crops. Several bioengineering mechanisms involved in stress signaling are being adopted in this regard. One example of this kind of manipulation is the osmotic adjustment. The quarternary ammonium compound glycinebetaine (GB), also originally referred to as betaine is a methylated glycine derivative. Among the betaines,… More >