Achille Gnassiri Wedaïna^1,2, Antonio Pizzi², Wolfgang Nzie¹, Raidandi Danwe³, Noel Konaï^4,*, Siham Amirou², Cesar Segovia⁵, Raphaël Kueny⁵

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.012782

Abstract The Piptadeniastrum Africanum bark tannin extract was characterized using MALDI TOF, ATR-FT MIR. It was used in the development of a resin with Vachellia nilotica extract as a biohardener. This tannin is consisting of Catechin, Quercetin, Chalcone, Gallocatechin, Epigallocatechin gallate, Epicatechin gallate. The gel time of the resin at natural pH (pH = 5.4) is 660 s and its MOE obtained by thermomechanical analysis is 3909 MPa. The tenacity of Urena lobata fibers were tested, woven into unidirectional mats (UD), and used as reinforcement in the development of biocomposite. The fibers tenacity at 20, 30 and 50 mm lengths are… More >

Medjda Amari¹, Kamel Khimeche^1,*, Abdelkader Hima² , Redouane Chebout³, Abderahmane Mezroua¹

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.013680

Abstract Recently, the exploitation of renewable plant resources in the formulation of adhesives is very promising for their availability at low coast, as well as their richness in biomolecules such as polyphenols. In this way, many research studies tannins extracted from different sources such as mimosa, quebracho, and pine have been the subject of very satisfactory recent studies. In this paper, a new complete characterization of the tannins extracted from the bark of eucalyptus globulus harvested from two regions in Algeria was achieved. The structural characterization enabled us to confirm the richness in condensed tannins, particularly in procyanidin and prodelphinidin units.… More >

Norma M. P. Machado¹, Gustavo C. Melo¹, Matheus F. Camargo¹, Giulianna G. Feijó¹, Bruna M. S. Putton², Clarice Steffens², Rogerio L. Cansian², Luiz A. Pessan¹, Francys K. V. Moreira^1,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.011081

Abstract Food packaging materials compounded with antimicrobial additives can substantially diminish the incidence of foodborne diseases. Here, poly(L-lactic acid) (PLA) films containing sodium metabisulfite (NaM) were produced by melt extrusion as an attempt to develop a new biodegradable material with antimicrobial properties for packaging. Life cycle assessment (LCA) simulations revealed that the environmental footprints of the PLA film did not change upon NaM addition, and that NaM is more eco-friendly than silver nanoparticles. The PLA/NaM films with NaM content varying from 0.5 to 5.0 wt.% were characterized by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and optical and mechanical properties determinations.… More >

Senyun Liu^1,2, Qinglin Liu^1,2, Xian Yi^1,2,*, Yizhou Shen^4,*, Long Guo^1,2, Wenqing Hou⁴, Haifeng Chen³, Zhen Wang⁴

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.014158

Abstract The aim of this study is to explore the heterogeneous ice nucleation behavior based on controllable micro-cubic array structure surfaces from the statistic perspective. To this end, we firstly constructed a group of micro-cubic array structures on silicon substrates by a selective plasma etching technique. After grafting low-free-energy substance, the as-constructed micro-cubic array structure surfaces exhibited higher non-wettability with the water contact angle being up to 150°. On this basis, 500 cycles of freezing and melting processes were accurately recorded to analyze the instantaneous ice nucleation behavior according to the statistical results of freezing temperature. As a consequence, the statistical… More >

Yang Li^#, Xiaoying Zha^#, Xingliang Xiong, Yan Zhang, Ying Feng, Haojiang Xie, Linqing Zhang, Qifeng Jiang^*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.012271

Abstract A silk fibroin (SF) spongy wound dressing incorporated with silver nanoparticles (Ag-NPs) was developed for biomedical applications. Ag-NPs were efficiently synthesized in situ via ultra violet (UV) with AgNO₃ as precursor and silk fibroin as reducing and protecting agent, respectively. After lyophilization, the formed silk fibroin spongy wound dressing (SFWD) exhibited polyporous morphology and inner lamellae structures, with uniform dispersion of Ag-NPs. The porous structure provided SFWD with the ability to absorb tissue exudatealmost 6 times of its own weight, which could guarantee the sustained release of Ag-NPs. By methanol treatment, SFWD showed much improved mechanical properties and more stable… More >

Zenghuan Gu¹, Aiguo Fang², Sudong Hua^1,*, Qingzhou Zhao², Lidong Sun², Fan Xia², Liying Qian³, Xiaojian Ren³

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.011912

Abstract The research used industrial by-products original phosphogypsum (PG) as the main raw material, slag (SG) and Portland cement (PC) as auxiliary materials, and the optimal additive amount was determined according to the compressive strength value of the sample. Comprehensively evaluate the water resistance and volume stability of the samples, and determine the best formula for new roadbed stabilized materials. The results showed that when the weight ratio of PG, slag and cement was OPG:SG:PC = 6:3:1, and mixed with 5% micro silica fume (MSF) and 3‰ hydroxypropyl methyl cellulose (HPMC), the sample’s comprehensive performance was the best, specifically, the sample’s… More >

Ilyas Renreng¹, Bakri Bakri^2,*, Sri Chandrabakty², Naharuddin²

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.012774

Abstract In this study, the influence of sodium hydroxide (NaOH) treatment and microwave treatment of coir fibers on the mechanical and physical properties of pressed coir fiber/epoxy composite were evaluated. The composite was fabricated with a hand lay-up method with compression molding. Before composite fabrication, pressed coir fiber was treated with NaOH and microwave treatments. Mechanical testing (tensile, flexural, and impact testing) of the composite was conducted. Then, water absorption and thickness swelling testing are also performed. The fractured composite surface morphology after the tensile test was analyzed by scanning electronic microscopy (SEM). The results revealed that tensile, flexural, and impact… More >

Nishit Savla¹, Raksha Anand², Soumya Pandit^2,*, Ram Prasad^3,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.011803

Abstract Microbial fuel cells (MFCs) are an attractive innovation at the nexus of energy and water security for the future. MFC utilizes electrochemically active microorganisms to oxidize biodegradable substrates and generate bioelectricity in a single step. The material of the anode plays a vital role in increasing the MFC’s power output. The anode in MFC can be upgraded using nanomaterials providing benefits of exceptional physicochemical properties. The nanomaterials in anode gives a high surface area, improved electron transfer promotes electroactive biofilm. Enhanced power output in terms of Direct current (DC) can be obtained as the consequence of improved microbe-electrode interaction. However,… More >

Lei Guo^1,2,3, Zi Guan¹, Lixia Guo^1,2,3,*, Weiping Shen¹, Zhilong Xue¹, Pingping Chen¹, Mingru Li¹

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.013415

Abstract A recycled aggregate (RA) was prepared by crushing and sieving demolished discarded concrete pavements and was subsequently tested and analyzed to determine its various physical properties. On this basis, pervious concrete (PC) mix proportions were designed. Coarse RA particles with sizes of 5–10 and 10–20 mm were selected. Concrete specimens were prepared with a water–cement ratio of 0.3, an aggregate–cement ratio of 4.5, the substitute rates of RA with 0, 25%, 50%, 75% and a single-/double-gap-graded RA mix (mass ratio of particles with sizes of 5–10 mm to particles with sizes of 10–20 mm: 1:1, 1:2, 2:1, 2:3 and 3:2).… More >

Wenbei Bi¹, Zengfeng Yan^1,*, Huan Zhao¹, Lixin Sun², Xudong Wang^3,4, Zhengmo Zhang³

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.012808

Abstract Murals in Mogao Grottoes consist of three parts: support layer, earthen plasters and paint layer. The earthen plasters play a key role in the preservation of murals. It is a mixture of Dengban soil, sand, and plant fiber. Two different natural fibers, hemp fiber and cotton fiber, were reinforced to earthen plasters in the same percentage to evaluate the influence on hygrothermal performance. The two types of earthen plasters were studied: one containing hemp fiber in the fine plaster (HFP) and the other containing cotton fiber in the fine plaster (CFP). Specific heat capacity, dry thermal conductivity, water vapor permeability,… More >