Qing Li¹, Ming Dai¹, Xueren Qian¹, Tian Liu¹, Zhenbo Liu¹, Yu Liu¹, Ming Chen¹, Wang He¹, Suqing Zeng¹, Yu Meng¹, Chenchen Dai¹, Jing Shen¹, Yingtao Liu¹, Wenshuai Chen¹, Wenbo Liu^1,*, Ping Lu^2,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.011655

Abstract Nanopaper has attracted considerable interest in the fields of films and paper research. However, the challenge of integrating the many advantages of nanopaper still remains. Herein, we developed a facile strategy to fabricate multifunctional nanocomposite paper (NGCP) composed of wood-derived nanofibrillated cellulose (NFC) and graphene as building blocks. NFC suspension was consisted of long and entangled NFCs (10–30 nm in width) and their aggregates. Before NGCP formation, NFC was chemically modified with a silane coupling agent to ensure that it could interact strongly with graphene in NGCP. The resulting NGCP samples were flexible and could be bent repeatedly without any… More >

H. N. Salwa¹, S. M. Sapuan^1,2,*, M. T. Mastura³, M. Y. M. Zuhri²

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.013977

Abstract Biopolymer composite has gained huge attention for its beneficial properties such as biodegradable and less impact to the environment. This consequently would diminish the dependency on the petroleum-based polymer. Abundance of studies have been done on the development and characterization of biopolymer composite materials for food packaging application, but work on the conceptual design of biopolymer composite packaging product is hardly found. Using the Kano Model, Quality Function Deployment for Environment (QFDE), morphological map, and Analytic Hierarchy Method (AHP) framework combination, this paper presents the conceptual design of a natural fibre reinforced biopolymer composites take-out food container. To understand customer… More >

Zhiqiang Shu, Jianmin Wu^*, Shaoqing Li, Bingbing Zhang, Jianqi Yang

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.014379

Abstract The use of steel slag, which is a by-product of the steel manufacture, in the construction of asphalt pavement would contribute to waste reduction and environment protection. Using rubber asphalt at the same time can improve the performance of asphalt mixture. This study investigates the influence of steel slag content on the road performance, thermal conductivity and outdoor temperature distribution of steel slag rubber asphalt mixtures (SSRAM), and calculates the cumulative stress in surface layer. At a certain range of concentration, the steel slag additive improved the deformation resistance and low-temperature cracking resistance of the mixtures. The SSRAM with 40%… More >

Jin Wang¹, Weigang Zhang^2,*, Xiaowei Zhuang^1,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.013269

Abstract Using 1–8 years bamboo as materials, the content of different chemical constituent was tested, and the reactive oxygen species (ROS) free radicals produced from laccase treated bamboo were detected by electron spin-resonance (ESR) spectroscope. The wet-process particleboard was made from laccase-treated bamboo by hot pressing and board mechanical properties including internal bond strength (IB), modulus of rupture (MOR) and thickness swelling (TS) after 2-hours water absorption were tested under different conditions. Results showed that laccase mainly catalyze the bamboo components and improved the bonding strength of laccase-treated boards. By ESR measurement on each single component such as milled bamboo lignin,… More >

Biqing Shu^1,2, Qin Ren¹, Lu Hong¹, Zhongping Xiao², Xiaoning Lu^1,*, Wenya Wang², Junbao Yu²,Naiqiang Fu², Yiming Gu², Jinjun Zheng²

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.012932

Abstract One of the large-scale industrial applications of Moso bamboo and poplar in China is the production of standardized fiberboard. When making fiberboard, a steam blasting pretreatment without the addition of traditional adhesives has become increasingly popular because of its environmental friendliness and wide applicability. In this study, the steam explosion pretreatment of Moso bamboo and poplar was conducted. The steam explosion pressure and holding time were varied to determine the influence of these factors on fiber quality by investigating the morphology of the fiber, the mass ratio of the unexploded specimen at the end face, the chemical composition, and the… More >

Qiaoxin Zhang^1,2, Rui Chen¹, Ding Jin², Chen Zhou^2,*, Xuewu Li^3,4,5,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.011596

Abstract In this paper, the microstructures and rolling contact fatigue behaviors of laser cladding Inconel 625 coatings with or without post-heat treatments were analyzed. The results revealed that the fatigue resistance of the laser cladding coating after any post-heat treatment was worse than that of the as-deposited coating. First, through the finite element analysis, the distribution of stress along the thickness direction of the coating was obtained, and it was concluded that the bonding interface between the coating and the matrix had little effect on the fatigue properties of the coating. Then X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy… More >

R. A. Rahman¹, A. Fazlizan^1,*, N. Asim¹, A. Thongtha²

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.013296

Abstract Autoclaved aerated concrete (AAC) has become more attractive due to its excellent and environmental-friendly properties in building construction. AAC is relatively lightweight, possesses lower thermal conductivity, higher heat resistance, lower shrinkage, and fasten construction than normal concrete. AAC is a combination of silica sand, cement, gypsum, lime, water, and an expansion agent. To improve its physical and mechanical properties and reduce its production cost, tremendous innovations where waste materials were utilized as partial replacement of AAC materials were done. This paper is intended to present the literature on the utilization of waste materials as a means of a partial replacement… More >

Qian Wang^1,#,*, Zhaozhao Liu^1,2,#,*, Xiumei Zhong¹, Zhongnan Gao¹, Fuqiang Liu²

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.014114

Abstract To effectively improve the poor engineering properties of loess and enhance its seismic performance, the industrial by-product lignin is used as a modified material. Based on lots of dynamic triaxial tests, the dynamic elastic modulus and damping ratio of lignin-modified loess were tested. The effects of lignin content on the dynamic elastic modulus and damping ratio of lignin-modified loess were analyzed. Combined with scanning electron microscopy (SEM) and X-ray diffraction (XRD), the microscopic mechanism of lignin to improve the dynamic properties of loess was studied. The results show that lignin can effectively modify the dynamic deformation of loess under dynamic… More >

Zhichao Lou^1,2, Tiancheng Yuan¹, Qiuyi Wang¹, Xinwu Wu¹, Shouheng Hu¹, Xiaomeng Hao¹, Xianmiao Liu^3,*, Yanjun Li^1,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.014285

Abstract This work aimed to help the bamboo industry develop methodology for producing imperfection-free bamboo boards that can serve either decorative or structural benefit to consumers seeking to engage with the bioeconomy. Specifi- cally, softened and slotted bamboo tubes were handled by a roller device with nails to render crack-free flattened bamboo board. Softening temperature and time were optimized herein according to findings regarding chemical composition and board mechanical properties. The optimal softening parameters for saturated steam heat treatment is proved to be 160°C for 8 minutes. The flattened bamboo board possesses an increased bending strength of 101.5 MPa and a… More >

Yipu Wang¹, Yonghua Wang^1,2,*, Zheming Liu¹, Huadong Yu¹, Jinkai Xu¹

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2021.014138

Abstract Noise pollution is one of the contemporary environmental pollution, which seriously damages people’s green and healthy life. In order to further improve the low frequency sound absorption performance of microperforated panel (MPP), a new plastocene coupled microperforated plate (PCMPP) is proposed. The acoustic properties of PCMPP with different apertures and perforation ratio were measured by transfer function method and compared with that of conventional MPPs. It is found that when the aperture was 0.8 mm, the peak value of sound absorption coefficient of PCMPP decreased by 150 Hz compared with MPP. In a certain range, PCMPP with larger apertures showed… More >