Yang Ming^1,2,3, Ping Chen^1,2,3,*, Yuanhao Wang^1,2,3,*, Ling Li^1,2,3, Xuandong Chen^1,2,3, Pengliang Sun^1,2,3,4

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.011929

Abstract In order to increase use ratio of steel slag solid waste, the concrete containing steel slag powder and zeolite powder as admixtures was prepared by using the orthogonal test method. The effects of water-binder ratio, sand ratio, steel slag powder content and zeolite powder on working properties, mechanical strength and chloride ion permeability of the concrete was studied. It was found that the early strength of the concrete had a decrease with the mixing of steel slag and zeolite powders, but its later strength approached to pure concrete. Moreover, the physical filling and pozzolanic activity of the admixtures increased the… More >

Raimundo N. Lima Júnior¹, João L. I. O. Almeida¹, Jones de Andrade², Flávia O. M. S. Abreu^1,*

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.011629

Abstract Biocoagulants emerges as a promising technology in water treatment, in order to exploit renewable and biodegradable materials. The present work aims to study the coagulant action of chitosan and carboxymethylchitosan on water with very high turbidity (above 300 NTU), contrasting the physicochemical results with those obtained for aluminum sulphate. Carboxymethylchitosan was produced by the Williamson’s ethers synthesis and characterized by potentiometric titration, FTIR and ¹ H-NMR. The coagulant tests were performed using synthetic water in a Jar-test equipment, through the induction of high and low velocity gradients, followed by sedimentation. The results showed turbidity and color removal efficiencies above 99%… More >

Ling Wang^1,2, Shenglong Jiang², Chenchen Huang², Pengyuan Dai², Fenghua Liu^2,*, Xiaopeng Qi¹, Gaojie Xu²

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.010544

Abstract The paper discusses the mechanical and thermal performance manifested in natural nanorods attapulgite (ATP) reinforced Acrylonitrile butadiene styrene (ABS) nanocomposites in the process of fused deposition modeling (FDM). Molten extrusion technique was taken to manufacture the filaments of ABS/organic-attapulgite (OAT) nanocomposites with different mass fraction and the printing operation was made by one commercial FDM three-dimensional (3D) printer. Results indicate that the mechanical performance of these FDM 3D printed specimens are improved obviously via the introduction of OAT, and tensile strength of the ABS/OAT nanocomposites parts with only 2 wt% OAT addition is enhanced by 48.1%. At the same time,… More >

Cheng Cheng^1,2,*, Weiwei Sun², Bo Hu³, Guixiang Tao², Chao Peng², Yanjuan Tian⁴, Shujuan Wu^4,5

Journal of Renewable Materials, Vol., , DOI:10.32604/jrm.2020.012054

Abstract The use of lignin, which is a by-product of the pulp and paper industry, in the development of asphalt binders would contribute to waste reduction, providing environmental, economic, and social benefits. In this study, samples of lignin-modified asphalt binder samples with different content of lignin (3%, 6%, 9%, 12%, and 15%) and unmodified asphalt (control) were tested using Fourier transform infrared spectroscopy (FTIR), dynamic shear rheometer (DSR), and thermogravimetry. The mechanism and effectiveness of lignin in improving the thermal stability of asphalt at high temperatures were analyzed. The FTIR analysis shows that no new characteristic absorption peak is seen in… More >