Jie Qu^1,2, Bingye Xu³, Quanlin Jin⁴

CMC-Computers, Materials & Continua, Vol.20, No.2, pp. 119-158, 2010, DOI:10.3970/cmc.2010.020.119

Abstract Large and complex macro-micro coupled constitutive models, which describe metal flow and microstructure evolution during metal forming, are sometimes overparameterized with respect to given sets of experimental datum. This results in poorly identifiable or non-identifiable model parameters. In this paper, a systemic parameter identification method for the large macro-micro coupled constitutive models is proposed. This method is based on the global and local identifiability analysis, in which two identifiability measures are adopted. The first measure accounts for the sensitivity of model results with respect to single parameters, and the second measure accounts for the degree of near-linear dependence of sensitivity… More >

Alamusi¹, Y.L. Liu¹, N. Hu^1,2

CMC-Computers, Materials & Continua, Vol.20, No.2, pp. 101-118, 2010, DOI:10.3970/cmc.2010.020.101

Abstract In this work, we propose a 3 dimensional (3D) numerical model to predict the piezoresistivity behaviors of a nanocomposite material made from an insulating polymer filled by carbon nanotubes (CNTs). This material is very hopeful for its application in highly sensitive strain sensor by measuring its piezoresistivity, i.e., the ratio of resistance change versus applied strain. In this numerical approach, a 3D resistor network model is firstly proposed to predict the electrical conductivity of the nanocomposite with a large amount of randomly dispersed CNTs under the zero strain state. By focusing on the fact that the piezoresistivity of the nanocomposite… More >

Richard K. F. Lee¹, James M. Hill²

CMC-Computers, Materials & Continua, Vol.20, No.1, pp. 85-100, 2010, DOI:10.3970/cmc.2010.020.085

Abstract In this study, we investigate the mechanics of a metallofullerene shuttle memory device, comprising a metallofullerene which is located inside a closed carbon nanotube. The interaction energy for the system is obtained from the 6-12 Lennard-Jones potential using the continuum approximation, which assumes that a discrete atomic structure can be replaced by an average atomic surface density. This approach shows that the system has two equal minimum energy positions, which are symmetrically located close to the tube extremities, and therefore it gives rise to the possibility of being used as a two-state memory device. On one side the encapsulated metallofullerene… More >

Wen-Hwa Chen^1,2, Tsung-Yu Huang¹

CMC-Computers, Materials & Continua, Vol.20, No.1, pp. 63-84, 2010, DOI:10.3970/cmc.2010.020.063

Abstract The contact characteristics between a droplet and a microchip/binding site strongly affect the accuracy of self-alignment in the self-assembly of micro-electronic-mechanical systems. This study is mainly to implement the Surface Evolver Program, which is commonly adopted for studying surface shaped by surface tension and other energies, to investigate comprehensively the contact characteristics between the small droplet and the microchip/binding site. The details of changes in the contact line and the contact area when the microchip is subjected to translation, compression, yawing and rolling are drawn. The three-dimensional deformation of the droplet between the microchip and the binding site is also… More >

Chih-Wen Chang¹

CMC-Computers, Materials & Continua, Vol.19, No.3, pp. 285-314, 2010, DOI:10.3970/cmc.2010.019.285

Abstract In this article, we propose a new numerical approach for solving these multi-dimensional nonlinear and nonhomogeneous backward heat conduction problems (BHCPs). A fictitious time t is employed to transform the dependent variable u(x, y, z, t) into a new one by (1+t)u(x, y, z, t)=: v(x, y, z, t, t), such that the original nonlinear and nonhomogeneous heat conduction equation is written as a new parabolic type partial differential equation in the space of (x, y, z, t, t). In addition, a fictitious viscous damping coefficient can be used to strengthen the stability of numerical integration of the discretized equations… More >

H. Wang¹, Y. Wu², P.D. Wu¹, K.W. Neale³

CMC-Computers, Materials & Continua, Vol.19, No.3, pp. 255-284, 2010, DOI:10.3970/cmc.2010.019.255

Abstract Large strain homogeneous simple shear of Hexagonal Close Packed (HCP) polycrystals is first studied numerically. The analyses are based on the classical Taylor model and the Visco-Plastic Self-Consistent (VPSC) model with various Self-Consistent Schemes (SCSs). In these polycrystal plasticity models, both slip and twinning contribute to plastic deformations. The simple shear results are then extended to the case of solid circular bars under large strain fixed-end torsion, where it is assumed that the solid bar has the same mechanical properties as the element analyzed for large strain simple shear. It is shown that the predicted second-order axial force is very… More >

M. Demiral, A. Roy, V. V. Silberschmidt¹

CMC-Computers, Materials & Continua, Vol.19, No.2, pp. 199-216, 2010, DOI:10.3970/cmc.2010.019.199

Abstract Static indentation experiments are typically performed to characterize the mechanical properties of a material of interest by a rigid indenter of known geometry to various depths. In contrast, dynamic indentation of materials has not been fully studied. Evaluating material performance under dynamic loading conditions is a challenge and we demonstrate that various modelling schemes may be appropriate for different flavours of dynamic indentation. In order to compare underlying thermo-mechanics and deformation processes in a static and dynamic indentation process, indentation of a rigid indenter into a workpiece to a fixed chosen penetration is extensively studied. A nonlinear strain rate and… More >

Sujoy Mukherjee¹, Ranjan Ganguli^1,2

CMC-Computers, Materials & Continua, Vol.19, No.2, pp. 105-134, 2010, DOI:10.3970/cmc.2010.019.105

Abstract In this study, variational principle is used for dynamic modeling of an Ionic Polymer Metal Composite (IPMC) flapping wing. The IPMC is an Electro-active Polymer (EAP) which is emerging as a useful smart material for `artificial muscle' applications. Dynamic characteristics of IPMC flapping wings having the same size as the actual wings of three different dragonfly species Aeshna Multicolor, Anax Parthenope Julius and Sympetrum Frequens are analyzed using numerical simulations. An unsteady aerodynamic model is used to obtain the aerodynamic forces. A comparative study of the performances of three IPMC flapping wings is conducted. Among the three species, it is… More >

Lutz Nasdala¹ , Andreas Kempe¹ and Raimund Rolfes¹

CMC-Computers, Materials & Continua, Vol.19, No.1, pp. 57-104, 2010, DOI:10.3970/cmc.2010.019.057

Abstract In order to understand the underlying mechanisms of inelastic material behavior and nonlinear surface interactions, which can be observed on macroscale as damping, softening, fracture, delamination, frictional contact etc., it is necessary to examine the molecular scale. Force fields can be applied to simulate the rearrangement of chemical and physical bonds. However, a simulation of the atomic interactions is very costly so that classical molecular dynamics (MD) is restricted to structures containing a low number of atoms such as carbon nanotubes. The objective of this paper is to show how MD simulations can be integrated into the finite element method… More >

Fangyi Li¹, Guangyao Li^2,3, Guangyong Sun², Zhen Luo⁴, Zheng Zhang²

CMC-Computers, Materials & Continua, Vol.19, No.1, pp. 37-56, 2010, DOI:10.3970/cmc.2010.019.037

Abstract The focus of this paper is concentrated on multi-disciplinary and multi-objective optimization for thin walled beam systems considering safety, normal mode, static loading-bearing and weight, in which the uncertainties of the parameters are described via intervals. The size and shape of the cross-section are treated as design parameters during optimization. Considering the lightweight and safety, the design problem is formulated with two individual objectives to measure structural weight and maximum energy absorption, respectively, constrained by the average force, normal mode and maximum stress. The optimization problem with uncertainties is further transformed into a deterministic optimization based on interval number programming.… More >