GAURAV AGARWAL

Journal of Polymer Materials, Vol.39, No.3-4, pp. 255-267, 2022, DOI:10.32381/JPM.2022.39.3-4.6

Abstract Studies were conducted to observe the effect of fracture toughness and damping response on fabric reinforced epoxy polymer composites. The samples of glass fabric, kevlar fabric and carbon fabric having 15wt%, 25wt%, 35wt%, 45wt% and 55wt % fabric content were prepared and tested following ASTM standards. Fracture toughness, peak load and increase in energy absorption are determined for the fabric-epoxy composites. Effect of temperature on storage modulus, loss modulus and tan delta values for various percentages of fabric epoxy composites are noticed and corresponding damping response behaviour is determined. The results revealed that reduction in strength at higher percentage of… More >

MUHAMAD SOFFI BIN MANDA^1,2, MOHD RUZAIMI BIN MAT REJAB¹, SHUKUR ABU HASSAN^3,4, MAT UZIR BIN WAHIT^3,4, JOSEPH SELVI BINOJ^5,*, BRIGHT BRAILSON MANSINGH⁶, SITI SAFARAH BINTI AMIRNUDDIN³, ALAMRY ALI⁷, KHENG LIM GOH^8,9, DIDIK NURHADIYANTO¹⁰

Journal of Polymer Materials, Vol.39, No.3-4, pp. 241-253, 2022, DOI:10.32381/JPM.2022.39.3-4.5

Abstract This study investigates the potential of Tin Slag Polymer Concrete (TSPC) strengthening through confinement using basalt fiber reinforced polymer (BFRP) and aramid fiber reinforced polymer (AFRP) confinement. TSPC short cylindrical column samples have been wrapped with BFRP and AFRP in a single layer (30 mm overlap) using Sikadur-330 epoxy and final samples were coded as TSPC-UC, TSPC-BF and TSPC-AF for unconfined, BFRP and AFRP for confined respectively. After curing for 30 days at room temperature, compressive test has been performed to know the strength, modulus, strain, fracture energy and failure modes of unconfined and confined TSPC. Test result shows that… More >

RITESH D. BHATT, JIGNESH P. PATEL, PARSOTAM H. PARSANIA^*

Journal of Polymer Materials, Vol.39, No.3-4, pp. 223-239, 2022, DOI:10.32381/JPM.2022.39.3-4.4

Abstract Compression-molded epoxy methacrylate of bisphenol-C-jute/treated jute-banana/groundnut/ cane sugar/pineapple leaf/rice husk/wheat husk sandwich composites were fabricated under 5 MPa pressure at room temperature for 3 h. Alkali treated jute-natural fiber sandwich composites displayed considerably improved mechanical properties over untreated jute-natural fiber sandwich composites due to surface modification of the jute fibers. Both types of sandwich composites showed high water uptake tendency, excellent hydrolytic stability against acids, alkali, and salt solutions, and also a longer equilibrium time at 30o C. Alkali treated sandwich composites revealed a considerably lower water uptake tendency than untreated sandwich composites. Observed water uptake trend is H₂ SO₄… More >

RITESH D. BHATT, JIGNESH P. PATEL, PARSOTAM H. PARSANIA^*

Journal of Polymer Materials, Vol.39, No.3-4, pp. 205-221, 2022, DOI:10.32381/JPM.2022.39.3-4.3

Abstract Epoxy methacrylate of bisphenol-C-jute/treated jute and their sandwich composites of white coir, brown coir, wild almond, bamboo, betel nut, and palmyra were prepared by a compression molding technique under 5MPa pressure and at room temperature for three h. The neat sample showed almost double tensile strength than its jute composite, while it is comparable for treated jute. The composites revealed substantially improved flexural strength compared to neat. The neat, jute/treated jute and their sandwich composites indicated good impact strength, pretty good Barcol hardness, and fairly good electric strength. The neat sample showed excellent volume resistivity, while jute/treated jute and their… More >

PARSOTAM H. PARSANIA^1,*, JIGNESH V. PATEL², JIGNESH P. PATEL³

Journal of Polymer Materials, Vol.40, No.3-4, pp. 271-284, 2023, DOI:10.32381/JPM.2023.40.3-4.9

Abstract Bisphenol-C epoxy crotonate resin was synthesized by reacting 8.09g epoxy resin of bisphenolC, and 2.15g crotonic acid using 25 mL 1,4-dioxane as a solvent, and 1 mL triethylamine as a catalyst at reflux temperature for 1-6 h. Solid epoxy crotonate (ECCR) is highly soluble in common organic solvents. ECCR was characterized by its acid (24.5-1.5 mg KOH/g) and hydroxyl (504.5-678.4 mg KOH/g) values. The structure of ECCR is supported by FTIR and 1 HNMR spectroscopic methods. A DSC endothermic transition at 229o C indicated melting followed by thermal polymerization of ECCR. ECCR is thermally stable up to 320o C and… More >

PRITI^1,*, RADHA SACHAN², ROLI PURWAR³

Journal of Polymer Materials, Vol.40, No.3-4, pp. 205-214, 2023, DOI:10.32381/JPM.2023.40.3-4.6

Abstract In current research work, we have studied the blending effect of non-mulberry silk fibroin (10% weight/volume basis) and gelatin (20% weight/volume basis) in formic acid. Several blends as SF10G0, SF2G8, SF3G7, SF5G5 and SF0G10 have been made and their rheological behaviour was investigated. The blend solutions were subjected to a steady shear rheological study in the variety of range of shear rates, namely 0.01–500 sec-1 and the viscosities of blend solutions were noticed to decrease in comparison to pure silk solution. The frequency sweep was employed in dynamic rheological tests to determine complex viscosity of these solutions from range of… More >

ARUN KUMAR M, JAYAKUMARI LS^*, RAMJI CHANDRAN

Journal of Polymer Materials, Vol.40, No.3-4, pp. 141-156, 2023, DOI:10.32381/JPM.2023.40.3-4.2

Abstract Nanocomposites are very important materials because it imparts superior properties than other composites with low level of filler loading. Styrene butadiene rubber (SBR) is a non-polar rubber which acts as an insulator and has low electrical conductivity. Graphene platelet nano-powder from 0.1 to 1.25 phr level is incorporated into SBR rubber in order to improve the electrical properties. Comparative studies on electrical and mechanical properties of styrene butadiene rubber with graphene platelet nano-powder (GPN) by varying the filler content are made. The incorporation of Graphene platelet nano-powder increases the electrical conductivity in styrene butadiene rubber. It has been observed that… More >

Lanying Chen^1,2, Qiumei Quan^3,*, Yunxiang Li³

Phyton-International Journal of Experimental Botany, Vol.93, No.3, pp. 551-566, 2024, DOI:10.32604/phyton.2024.048103

Abstract Mediated by pollen flow, natural hybridization is deemed a crucial factor that propels speciation in floral plants. Despite the fact that the diversity of Epimedium species is concentrated mainly in Southwestern China, the potential impact of interspecific pollination on natural hybridization has yet to be empirically scrutinized. To explore this, we studied the flowering period and the visitors of flowers in three frequently overlapping Epimedium species at Jinchengshan National Forest Park, located in Nanchong, Sichuan Province. Additionally, we performed a series of pollination experiments to examine breeding systems and hybrid compatibility. Morphologically, Epimedium pubescens and Epimedium wushanense are clearly distinct… More >

Xiaojie Liang^1,2, Wei An², Yuekun Li², Yajun Wang², Xiaoya Qin², Yanhong Cui¹, Shuchai Su^1,*

Phyton-International Journal of Experimental Botany, Vol.93, No.3, pp. 467-486, 2024, DOI:10.32604/phyton.2024.047628

Abstract

Goji berry (Lycium barbarum L.) is substantially dependent on nitrogen fertilizer application, which can significantly enhance fruit yield and Goji berry industrial development in Ningxia, China. This study aimed to analyze the functions of differential nitrogen application rates including low (N1), medium (N2), and high (N3) levels in soil microbial community structure (bacterial and fungal) at 2 diverse soil depths (0–20, 20–40 cm) through high-throughput sequencing technology by targeting 16S RNA gene and ITS1 & ITS2 regions. All the observed physicochemical parameters exhibited significant improvement (p < 0.05) with increased levels of nitrogen and the highest values for most parameters… More >

NURUL HAYATI YUSOF^1,*, DAZYLAH DARJI¹, TAN KIM SONG¹, NGHIEM THI THUONG²

Journal of Polymer Materials, Vol.39, No.1-2, pp. 151-166, 2022, DOI:10.32381/JPM.2022.39.1-2.10

Abstract In this work, a pure gum mould made of prevulcanized natural rubber/cloisite-Na⁺ nanocomposite (PVNR/CN) was prepared and characterized for ornament application. The suitable conditions to prepare PVNR/CN latex mixtures and the properties of the resulting PVNR/CN nanocomposites were investigated. The optimum CN concentration in the latex mixture was 1.0 phr, with the properties of 60 wt% total solid content, more than 600 sec mechanical stability time, lower than 350 cP Brookfield viscosity, and pH 10. The properties of PVNR/CN nanocomposite showed high strength, moderate hardness, and good thermal stability. The morphology by TEM showed well dispersion of CN particles in… More >