Qingguo Ben¹, Congcong Zhang², Benkai Shi², Huifeng Yang^2,*

Journal of Renewable Materials, Vol.10, No.12, pp. 3599-3610, 2022, DOI:10.32604/jrm.2022.022344

Abstract Stress laminated timber (SLT) deck is assembled using timber (lumber or glulam) components placed side by side and stressed together, which has the advantages of easy prefabrication and good cost performance. This work presented an experimental investigation of bending tests performed on SLT slabs. Several parameters, including prestress levels, distance of pre-stressing bars, and the existence of self-tapping screw (STS) reinforcement, were taken into consideration. To reinforce the compressive property of timber perpendicular to the grain, the STSs were placed under the anchor plate of the pre-stressed bars. The experimental results were analyzed and discussed in terms of failure modes,… More > Graphic Abstract

Norshariza Mohamad Bhkari^1,2,*, Lum Wei Chen¹, Anis Azmi², Muhammad Shaiful Nordin², Norman Wong Shew Yam³, Zakiah Ahmad², Lee Seng Hua⁴

Journal of Renewable Materials, Vol.10, No.11, pp. 2851-2869, 2022, DOI:10.32604/jrm.2022.022326

Abstract This study investigated the bending, compression as well as the bonding performance of CLT panels made from fast-growing timber species, i.e., Laran (Neolamarckia cadamba) and Batai (Paraserianthes falcataria). The variables studied were timber species (Laran and Batai), layers of lamination (3-layer and 5-layer), loading direction in bending (in-plane and out-of-plane), loading direction in compression (x-, y-, and z-axis) and different treatment conditions for bonding performance test. The desired outputs of this study were bending and compression properties (strength and stiffness) as well as bonding performance (block shear strength, wood failure percentage and delamination value). The bending and compression test were… More >

Mohammad Zohurul Islam¹, Rabindra Nath Mondal², Suvash C. Saha^1,*

Energy Engineering, Vol.119, No.2, pp. 453-472, 2022, DOI:10.32604/ee.2022.018160

Abstract

A depth understanding of fluid flow past a curved duct having rectangular cross-section with different aspect ratios (l) are essential for various engineering applications such as in chemical, mechanical, bio-mechanical and bio-medical engineering. So highly ambitious researchers have given significant attention to study new characteristics of fluid flow in a curved duct. The flow characterization in the rectangular duct has been studied over a wide range of numerical and selective experimental studies. However, proper knowledge with the effects of Coriolis force for different aspect ratios is important for better understanding of the transitional behaviour and the subsequent heat generation, which… More >

Mohammad Anwar-Us-Saadat¹, Janeshka Goonewardena², Bidur Kafle², Mahmud Ashraf^2,*, Mahbube Subhani²

Journal of Renewable Materials, Vol.10, No.6, pp. 1575-1606, 2022, DOI:10.32604/jrm.2022.018919

Abstract Cross laminated timber (CLT) is an innovative and environment friendly engineered timber product with superior structural performance. CLT offers strong resistance against both in-plane and out-of-plane loading. Hence, it is widely used as floors, roofs or wall elements. Considerable experimental research on CLT under various loading conditions has been done in the recent past. This article presents a comprehensive review of various design methods to determine basic mechanical properties such as tension, compression and rolling shear strength of CLT with primary focus on Norway spruce. All relevant experimental data available from existing literature were collated and consequently been used to… More >

Yifei Yin, Lirong Qu, Weidong Lu^*, Chengshuai Li

Journal of Renewable Materials, Vol.10, No.6, pp. 1517-1535, 2022, DOI:10.32604/jrm.2022.018149

Abstract Creep test results of glulam members under compression and bending were studied in this paper. The creep tests were conducted to investigate the influence of the stress level and relative eccentricity on the creep deformation of glulam members. The test results showed that the creep deformation trends of glulam members under long-term compression and bending loading were similar; the creep deformation increased with increases in both the stress level and relative eccentricity. However, the relative creep deformation decreased with the increase in both the stress level and relative eccentricity under long-term loading, and a five-parameter creep model was proposed to… More > Graphic Abstract

Benedikt Plaumann^*

Sound & Vibration, Vol.56, No.1, pp. 1-19, 2022, DOI:10.32604/sv.2022.018634

Abstract This contribution shows an analysis of vibration measurement on large floor-mounted traction batteries of Battery Electric Vehicles (BEV). The focus lies on the requirements for a realistic replication of the mechanical environments in a testing laboratory. Especially the analysis on global bending transfer functions and local corner bending coherence indicate that neither a fully stiff fixation of the battery nor a completely independent movement on the four corners yields a realistic and conservative test scenario. The contribution will further show what implication these findings have on future vibration & shock testing equipment for large traction batteries. Additionally, it will cover… More >

Ting Huang, Xin Zhuo^*

Journal of Renewable Materials, Vol.10, No.4, pp. 993-1005, 2022, DOI:10.32604/jrm.2022.017373

Abstract The construction of grouting butt joints of bamboo tubes is simple and efficient. However, when the joint is bent, the low tensile strength of the mortar easily leads to cracking of the mortar prior to the failure of the bamboo tube. In this paper, a comparative test of the bending capacity was performed on grouting butt joints reinforced by nonperforated, fully perforated, and semiperforated steel plates embedded in bamboo tubes to obtain the load-displacement curves and ultimate bearing capacity of various specimens. The strengthening effect of CFRP pasted on bamboo tubes was also studied. The results show that the opening… More > Graphic Abstract

Yujie Huang¹, Yifan Zhang¹, Zheng Wang^1,*, Assima Dauletbe², Yao Lu¹, Zhaoyu Shen¹

Journal of Renewable Materials, Vol.10, No.3, pp. 849-870, 2022, DOI:10.32604/jrm.2022.018515

Abstract To describe the dynamic cracking process of the CLT vertical layer, the correlation between a load-displacement curve, specimen cracking, and planar shear failure mechanism of the CLT were explored. A three-point bending test and an improved planar shear test are used to evaluate the shear performance of the CLT. In this study, the load-displacement curve is recorded, the experimental part is synchronized with the video, the dynamic process of cracking of the vertical layer is observed and analyzed throughout the test. From the load-displacement curve, the image characteristics of the initial cracking and the sudden increase of the cracking of… More > Graphic Abstract

Ting Wang¹, Zhiqiang Wang^1,*, Yin Yang¹, Jianhui Zhou^2,*

Journal of Renewable Materials, Vol.10, No.2, pp. 527-540, 2022, DOI:10.32604/jrm.2022.017955

Abstract The acoustic emission (AE) technique can perform non-destructive monitoring of the internal damage development of bamboo and wood materials. In this experiment, the mechanical properties of different bamboo and wood (bamboo scrimber, bamboo plywood and SPF (Spruce-pine-fir) dimension lumber) during four-point loading tests were compared. The AE activities caused by loadings were investigated through the single parameter analysis and K-means cluster analysis. Results showed that the bending strength of bamboo scrimber was 3.6 times that of bamboo plywood and 2.7 times that of SPF dimension lumber, respectively. Due to the high strength and toughness of bamboo, the AE signals of… More > Graphic Abstract

Hasan Sabah Hasan^1,*, Abdallah A. Abdallah², Imran Khan³, Hala Sadek Alosman⁴, Ayshan Kolemen⁵, Bilal Alhayani⁶

CMC-Computers, Materials & Continua, Vol.68, No.3, pp. 3499-3511, 2021, DOI:10.32604/cmc.2021.015968

Abstract True unilateral posterior crossbite in adults is a challenging malocclusion to treat, especially when we need to correct cross-arch segments with unwanted effects on non-cross segments. Conventional expansion methods are expected to have some shortcomings; the Unilateral dental expander appliance used to restore unilateral cross bite dental arch is an uncommon appliance; for this, a designed new device is needed. This paper aimed to invite a new unilateral dental expander appliance (UDEX) to treat unilateral dental posterior crossbite in adults using available dental material, easy to use and handle, well tolerated by the patient, and biocompatible with oral structure. It… More >