Jennifer D. Rhymer¹, Hyonny Kim¹

CMC-Computers, Materials & Continua, Vol.35, No.2, pp. 87-117, 2013, DOI:10.3970/cmc.2013.035.087

Abstract Polymer matrix composite structures are exposed to a variety of impact threats including hail ice. Internal delamination damage created by these impacts can exist in a form that is visually undetectable. This paper establishes an analysis methodology for predicting the onset of delamination damage in toughened carbon/epoxy composite laminates when impacted by high velocity ice spheres (hailstones). Experiments and analytical work focused on ice sphere impact onto composite panels have determined the failure threshold energy as a function of varying ice diameter and panel thickness, and have established the ability to predict the onset of delamination using cohesive elements in… More >

Chandra Veer Singh^1,*

CMC-Computers, Materials & Continua, Vol.34, No.3, pp. 227-249, 2013, DOI:10.3970/cmc.2013.034.227

Abstract A non-linear damage model is developed for the prediction of stiffness degradation in composite laminates due to transverse matrix cracking. The model follows the framework of a recently developed synergistic damage mechanics (SDM) approach which combines the strengths of micro-damage mechanics and continuum damage mechanics (CDM) through the so-called constraint parameters. A common limitation of the current CDM and SDM models has been the tendency to over-predict stiffness changes at high crack densities due to linearity inherent in their stiffness-damage relationships. The present paper extends this SDM approach by including higher order damage terms in the characterization of ply cracking… More >

A. Ataş¹, C. Soutis²

CMC-Computers, Materials & Continua, Vol.34, No.3, pp. 199-226, 2013, DOI:10.3970/cmc.2013.034.199

Abstract A strength prediction method is presented for double-lap single fastener bolted joints of cross-ply carbon fibre reinforced plastic (CFRP) composite laminates using cohesive zone elements (CZEs). Three-dimensional finite element models were developed and CZEs were inserted into subcritical damage planes identified from X-ray radiographs. The method makes a compromise between the experimental correlation factors (dependant on lay-up, stacking sequence and joint geometry) and three material properties (fracture energy, interlaminar strength and nonlinear shear stress-strain response). Strength of the joints was determined from the predicted load-displacement curves considering sub-laminate and plylevel scaling effects. The predictions are in a reasonable agreement with… More >

A Rama Chandra Murthy¹, Smitha Gopinath^1,2, Ashish Shrivastav¹, G. S. Palani¹, Nagesh R. Iyer¹

CMC-Computers, Materials & Continua, Vol.25, No.1, pp. 1-18, 2011, DOI:10.3970/cmc.2011.025.001

Abstract This paper presents methodologies for crack growth study and fatigue remaining life prediction of reinforced concrete structural components accounting for the corrosion effects. Stress intensity factor (SIF) has been computed by using the principle of superposition. At each incremental crack length, net SIF has been computed as the difference of SIF of plain concrete and reinforcement. The behaviour of reinforcement has been considered as elasto-plastic. Uniform corrosion rate has been assumed in the modeling. Corrosion effect has been accounted in the form of reduction in the diameter and modulus of elasticity of steel. Numerical studies have been carried out to… More >

Smitha Gopinath^1,2, A. Ramach,ra Murthy¹, Nagesh R. Iyer¹

CMC-Computers, Materials & Continua, Vol.22, No.1, pp. 55-72, 2011, DOI:10.3970/cmc.2011.022.055

Abstract This paper presents the mathematical modeling techniques for nonlinear finite element analysis of RC structure to incorporate uniform corrosion effects. Effect of corrosion has been simulated as reduction in effective cross-sectional area of reinforcing bar, reduction in bonding phenomena and as reduction in material properties of reinforcing bar such as yield strength and elastic modulus. Appropriate constitutive laws for (i) corroded rebar elements and (ii) bond slip with corroded bar have been described. Procedure has been outlined to determine the global damage indicator by secant stiffness based approach. A corroded RC beam has been analysed to validate the proposed model… More >

Bin Li¹, Guo-biao Yang¹, Qi-rong Zhu², Fan Ni²

CMC-Computers, Materials & Continua, Vol.21, No.2, pp. 107-118, 2011, DOI:10.3970/cmc.2011.021.107

Abstract In this paper, digital image correlation method (DICM) is employed to measure the shear behavior of the spot welding specimens and the ones using adhesive under quasi-static lap shear testing. The images of the specimens' surfaces are captured in real-time by CCD and corresponding computer system. DICM is subsequently used to obtained strain by correlating the images captured before and after deformation. Then, both force-displacement curves and stress-strain curves of the specimens including the cracking load are obtained. The results and analysis show that the mechanical properties of specimens using adhesive compared with the spot welding specimens have an obvious… More >

V.G.Yakhno¹

CMC-Computers, Materials & Continua, Vol.21, No.1, pp. 1-16, 2011, DOI:10.3970/cmc.2011.021.001

Abstract Homogeneous non-dispersive anisotropic materials, characterized by a positive constant permeability and a symmetric positive definite conductivity tensor, are considered in the paper. In these anisotropic materials, the electric and magnetic dyadic Green's functions are defined as electric and magnetic fields arising from impulsive current dipoles and satisfying the time-dependent Maxwell's equations in quasi-static approximation. A new method of deriving these dyadic Green's functions is suggested in the paper. This method consists of several steps: equations for electric and magnetic dyadic Green's functions are written in terms of the Fourier modes; explicit formulae for the Fourier modes of dyadic Green's functions… More >

N.J. Bartle¹, P.D. Gosling¹

CMC-Computers, Materials & Continua, Vol.20, No.1, pp. 19-62, 2010, DOI:10.3970/cmc.2010.020.019

Abstract ETFE cushions are increasingly being used to form high-profile facades and structural forms. This investigation aims to extend an analytical theory of large deformation in order to predict the shape and stress distributions of an un-patterned square ETFE cushion without the need to resort to discretised numerical methods. In order to assess the validity of the theoretical procedure a prototype cushion has been analysed using a finite element simulation. The theoretical procedure is also compared with alternative approximate equations proposed for the design of ETFE cushions. More >

Surkay D. Akbarov^1,2, Resat Kosker³, Yasemen Ucan³

CMC-Computers, Materials & Continua, Vol.17, No.2, pp. 77-102, 2010, DOI:10.3970/cmc.2010.017.077

Abstract In the framework of the piecewise homogeneous body model with the use of the three-dimensional geometrically non-linear exact equations of the theory of elasticity, the method for determination of the stress-strain state in the infinite body containing periodically located row of periodically curved fibers is developed. It is assumed that the midlines of the fibers are in the same plane. With respect to the location of the fibers according to each other the sinphase and antiphase curving cases are considered. Numerical results on the effect of the geometrical non-linearity to the values of the self balanced shear and normal stresses… More >

Veturia Chiroiu¹, Ligia Munteanu¹, Pier Paolo Delsanto²

CMC-Computers, Materials & Continua, Vol.16, No.1, pp. 75-100, 2010, DOI:10.3970/cmc.2010.016.075

Abstract Conventional continuum theories are unable to capture the observed indentation size effects, due to the lack of intrinsic length scales that represent the measures of nanostructure in the constitutive relations. In order to overcome this deficiency, the Toupin-Mindlin strain gradient theory of nanoindentation is formulated in this paper and the size dependence of the hardness with respect to the depth and the radius of the indenter for multiple walled carbon nanotubes is investigated. Results show a peculiar size influence on the hardness, which is explained via the shear resistance between the neighboring walls during the buckling of the multiwalled nanotubes. More >