K. Sefiane¹

FDMP-Fluid Dynamics & Materials Processing, Vol.1, No.3, pp. 267-276, 2005, DOI:10.3970/fdmp.2005.001.267

Abstract In this paper the experimental results on the wetting behaviour of volatile binary sessile drops are reported. The evaporation rate is varied through the control of the ambient total pressure. The dynamic wetting contact angle of an evaporating Water-Ethanol drop is investigated at various sub-atmospheric pressures. The wetting properties (contact angle, shape and volume) are monitored in time using a drop shape analysis instrument. The results show that the evaporation of the binary droplet takes place in two stages: the first stage where the wetting behaviour is very similar to the pure ethanol case and a second stage where the… More >

P. Yu¹, T. S. Lee¹, Y. Zeng¹, H. T. Low²

FDMP-Fluid Dynamics & Materials Processing, Vol.1, No.3, pp. 235-246, 2005, DOI:10.3970/fdmp.2005.001.235

Abstract A numerical model is developed for the investigation of flow field and mass transport in a micro-bioreactor, of working volume below 5 ml, in which medium mixing is generated by a magnetic stirrer-rod rotating on the bottom. The flow-field results show that a recirculation region exists above the stirrer rod and rotates with it; the related fluid mixing is characterized by a circulation coefficient of up to 0.2 which is about five times smaller than that of a one-litre stirred-tank bioreactor. The oxygen transfer coefficient is less than 5 h^-1 which is two orders smaller than that of a 10-litre… More >

A.Yu. Gelfgat¹, A. Rubinov², P.Z. Bar-Yoseph², A. Solan²

FDMP-Fluid Dynamics & Materials Processing, Vol.1, No.1, pp. 21-32, 2005, DOI:10.3970/fdmp.2005.001.021

Abstract The three-dimensional instability of the thermocapillary convection in cylindrical undeformable floating zones heated laterally is studied numerically. Different types of the boundary conditions, including radiation heating, linearized radiation and prescribed heat flux are used in the calculation. Stability diagrams showing the Prandtl number dependence of the critical Marangoni numbers that represent the thermocapillary forcing for different heating conditions are reported. It is shown that the primary instability of initially axisymmetric thermocapillary flows is defined mainly by the total amount of heat supplied through the heated side surface. The way in which the heat is supplied has a less significant effect… More >

Kai Wang¹, Guojian Li¹, Qiang Wang^1,2, Huimin Wang¹, Jiaojiao Du¹, Jicheng He¹

CMC-Computers, Materials & Continua, Vol.38, No.2, pp. 79-89, 2013, DOI:10.3970/cmc.2013.038.079

Abstract Study on the behaviors of the melting and coalescence of clusters in atomic scale may create new structure at nanoscale, which is a very important research field. The structural evolutions of clusters Cu₃₂₁, Co₃₂₁, and Ni₃₂₁ during their melting and coalescence processes were studied using molecular dynamics simulation with a general embedded atom method in this paper. It was found that the geometries of Cu₃₂₁ and Co₃₂₁ transformed to icosahedron from fcc near their melting points, which leads to the increase of their melting points. Concerning the coalescence, it was found that Cu atoms easily formed a coating layer on… More >

Yuhang Jing¹, Ming Hu^2,3

CMC-Computers, Materials & Continua, Vol.38, No.1, pp. 43-59, 2013, DOI:10.3970/cmc.2013.038.043

Abstract Nanostructuring of thermoelectric materials bears promise for manipulating physical parameters to improve the energy conversion efficiency of thermoelectrics. In this paper the thermal transport in Si/Ge superlattice nanotubes is investigated by performing nonequilibrium molecular dynamics simulations aiming at realizing low thermal conductivity by surface roughening. Our calculations revealed that the thermal conductivity of Si/Ge superlattice nanotubes depends nonmonotonically on periodic length and increases as the wall thickness increases. However, the thermal conductivity is not sensitive to the inner diameters due to the strong surface scattering at thin wall thickness. In addition, introducing roughness onto the superlattice nanotubes surface can destroy… More >

R Sivaprasad^1,2, S Venkatesha¹, C S Manohar^1,3

CMC-Computers, Materials & Continua, Vol.9, No.3, pp. 179-208, 2009, DOI:10.3970/cmc.2009.009.179

Abstract The problem of identifying parameters of time invariant linear dynamical systems with fractional derivative damping models, based on a spatially incomplete set of measured frequency response functions and experimentally determined eigensolutions, is considered. Methods based on inverse sensitivity analysis of damped eigensolutions and frequency response functions are developed. It is shown that the eigensensitivity method requires the development of derivatives of solutions of an asymmetric generalized eigenvalue problem. Both the first and second order inverse sensitivity analyses are considered. The study demonstrates the successful performance of the identification algorithms developed based on synthetic data on one, two and a 33… More >

Walter Gerstle¹, Stewart Silling², David Read³, Vinod Tewary⁴, Richard Lehoucq⁵

CMC-Computers, Materials & Continua, Vol.8, No.2, pp. 75-92, 2008, DOI:10.3970/cmc.2008.008.075

Abstract A theoretical framework, based upon the peridynamic model, is presented for analytical and computational simulation of electromigration. The framework allows four coupled physical processes to be modeled simultaneously: mechanical deformation, heat transfer, electrical potential distribution, and vacancy diffusion. The dynamics of void and crack formation, and hillock and whisker growth can potentially be modeled. The framework can potentially be applied at several modeling scales: atomistic, crystallite, multiple crystallite, and macro. The conceptual simplicity of the model promises to permit many phenomena observed in microchips, including electromigration, thermo-mechanical crack formation, and fatigue crack formation, to be analyzed in a systematic and… More >

Jae In Kim¹, Kilho Eom², Moon Kyu Kwak³, Sungsoo Na⁴

CMC-Computers, Materials & Continua, Vol.8, No.2, pp. 67-74, 2008, DOI:10.3970/cmc.2008.008.067

Abstract This paper concerns the application of component mode synthesis for biomolecule modeling to understand protein dynamics. As for protein dynamics, eigenvalue problem should be formulated to obtain eigenvalue, eigenvector and thermal fluctuation. To describe the thermal fluctuation of protein, normal mode analysis is introduced and normal modes identify the dynamic behavior of protein very well. Component mode synthesis considers the given complex structure as an assembly of smaller components. The selection of a component may be arbitrary. When the component mode synthesis is applied to formulate the eigenvalue problem of protein structure, we selected a protein which may be composed… More >

X.G. Yuan^1,2, R.J. Zhang³, H.W. Zhang¹

CMC-Computers, Materials & Continua, Vol.7, No.3, pp. 155-166, 2008, DOI:10.3970/cmc.2008.007.155

Abstract In this paper, the dynamic inflation problems are examined for infinitely long cylindrical tubes composed of a class of transversely isotropic incompressible Ogden material models. The inner surface of the tube is subjected to a class of periodic step radial pressures relating to time. The influences of various parameters, namely, the material parameters, the structure parameters and the applied pressures, on dynamic behaviors of the tube are discussed in detail. Significantly, for some given material parameters, it is proved that the motion of the tube would present a class of nonlinear periodic oscillations for any given pressures and the amplitude… More >

Haomiao Zhou^1,2, Youhe Zhou^1,3, Xiaojing Zheng¹

CMC-Computers, Materials & Continua, Vol.6, No.3, pp. 201-212, 2007, DOI:10.3970/cmc.2007.006.201

Abstract This paper presents some simulation results of nonlinear dynamic responses for a laminated composite beam embedded by actuators of the giant magnetostrictive material (Terfenol-D) subjected to external magnetic fields, where the giant magnetostrictive materials utilizing the realignment of magnetic moments in response to applied magnetic fields generate nonlinear strains and forces significantly larger than those generated by other smart materials. To utilize the full potential application of the materials in the function and safety designs, e.g., active control of vibrations, the analysis of dynamic responses is requested in the designs as accurately as possible on the basis of those inherent… More >