Ummid I. Shaikh^a , Sonali Kale^b, Anirban Sur^c, Anindita Roy^c

Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-10, 2023, DOI:10.5098/hmt.20.28

Abstract The requirement for sustainable development for buildings is to have environmentally friendly cooling and heating systems. The utilization of phase change materials (PCM) in the cooling system is a potential solution for minimizing active power requirements as well as for reducing the size of components of a vapor compression refrigeration VCR system. A prototype of an Air-PCM (T25™) heat exchanger was fabricated and tested in actual environmental conditions. Experimental trials using a salt hydrate as PCM have shown the maximum cooling effect of 2.05 kW when 75% of the PCM was solidified. Based on the results, it is found that… More >

Ameer Abed Jaddoa^* , Karema Assi Hamad, Arshad Abdul Jaleil Hameed

Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-9, 2023, DOI:10.5098/hmt.20.18

Abstract In the Heat Transfer process, many innovations were introduced aiming to obtain the most optimum behavior of the cooling process using nanofluids as coolant liquids. These nanofluids have gained much attention in cooling systems due to their special rheological and thermal performance. In this work, an experimental evaluation is conducted for nanofluids Al₂O₃, SiO₂, CuO, ZnO, and TiO₂ nanoparticles applied to a mini-channel. The nanofluid particles were entirely spread out in purified water (size of 15 nm) before being passed to the heat sink through a confined inflow channel. The obtained results showed that the achieved improvement rates are 25%,20%,… More >

Hussein Al-Gburi^*, Akeel Abbas Mohammed, Audai Hussein Al-Abbas

Frontiers in Heat and Mass Transfer, Vol.20, pp. 1-7, 2023, DOI:10.5098/hmt.20.17

Abstract Transferring thermal energy efficiently necessitates utilizing a heat exchanger capable of producing the full thermal power of the energy supply at lowest possible cost and time. Therefore, in the present investigation, the impact of corrugated helical coil concentric tube-in-tube heat exchanger on the thermal performance is investigated experimentally. As a continuous in our issue of heat exchanger, the corrugated helical tube-in-tube is carried out and compared with smooth helical tube-in-tube for free convection heat transfer. The set-up of the experimental apparatus are designed and utilized to be appropriate for the cooling and heating systems of working fluid. The impacts of… More >

Jianwei Zhang¹, Yue Yin¹, Lei Shi¹, Yi Han², Mi Zhou^3,*, Xihong Zhang⁴

Journal of Renewable Materials, Vol.11, No.6, pp. 2893-2911, 2023, DOI:10.32604/jrm.2023.025436

Abstract Dust is an environmental and health hazard. In this study, a new technology for dust suppressant is introduced using soybean urease with an optimal cementing solution. Calcium carbonate is produced by soybean urease and cementing solution, which bonds the soil particles towards a dust suppressant. A laboratory wind tunnel test is carried out to examine its effectiveness and discover possible optimization solutions. Several factors, including soybean meal concentration, cementing solution concentration, and volume of solution per unit area, are examined to quantify their influences on soil transport mass, evaporation ratio, evaporation rate, surface strength, water retention ratio, and infiltration rate… More >

Yue Chen^1,2, Haitao Li^1,2,*, Lei Gao^3,*, Wei Xu^1,2, Rodolfo Lorenzo⁴, Milan Gaff^5,6

Journal of Renewable Materials, Vol.11, No.6, pp. 2787-2808, 2023, DOI:10.32604/jrm.2023.027634

Abstract Bamboo is an eco-friendly material with light weight, high strength, short growth cycle and high sustainability, which is widely used in building structures. Engineered bamboo has further promoted the development of modern bamboo structures due to its unrestricted size and shape. However, as a fiber-reinforced material, fracture damage, especially Mode I fracture damage, becomes the most likely damage mode of its structure, so Mode I fracture characteristics are an important subject in the research of mechanical properties of bamboo. This paper summarizes the current status of experimental research on the Mode I fracture properties of bamboo based on the three-point… More >

Yuhang He, Rongzhuo Zhang, Yifan Zhang, Zheng Wang^*

Journal of Renewable Materials, Vol.11, No.6, pp. 2729-2743, 2023, DOI:10.32604/jrm.2023.025867

Abstract In order to better meet the objective requirements of the use safety of the high-rise glulam building floor structure and the living comfort of the residents, the transient excitation, environmental excitation and frequency spectrum identification methods were used to carry out experimental modal test in-site on the three rooms numbered A, B and C of the same glulam structural building. The three rooms have different functions, different floor sizes and different floor supporting structures. The research results have shown that the first-order bending frequency of the floor structure of Room A is 27.50 Hz, the transverse second-order bending frequency is… More > Graphic Abstract

Ningbo Guo, Xianming Gao^*, Duanling Li, Jixing Zhang, Penghui Yin, Mengyi Hua

CMES-Computer Modeling in Engineering & Sciences, Vol.136, No.3, pp. 3061-3082, 2023, DOI:10.32604/cmes.2023.026657

Abstract Computational fluid dynamics was used and a numerical simulation analysis of boiling heat transfer in microchannels with three depths and three cross-sectional profiles was conducted. The heat transfer coefficient and bubble generation process of three microchannel structures with a width of 80 μm and a depth of 40, 60, and 80 μm were compared during the boiling process, and the factors influencing bubble generation were studied. A visual test bench was built, and test substrates of different sizes were prepared using a micro-nano laser. During the test, the behavior characteristics of the bubbles on the boiling surface and the temperature… More >

Guoqing Long¹, Guogang Zhang¹, Qi Zhang², Cuilin Zhao², Suoying He^2,*, Fengzhong Sun²

FDMP-Fluid Dynamics & Materials Processing, Vol.19, No.7, pp. 1789-1801, 2023, DOI:10.32604/fdmp.2023.026559

Abstract In recent years, water collecting systems, with the associated advantages of energy saving and noise reduction, have become the foundation for the development of a scheme to optimize the structure of cooling towers. To explore the feasibility of this approach for mechanical draft cooling towers, a small-scale experimental device has been built to study the resistance and splash performances of three U-type water collecting devices (WCDs) for different water flow rates and wind speeds. The experimental results show that within the considered ranges of wind speed and water flow rate, the pressure drop of the different WCDs can vary significantly.… More > Graphic Abstract

Alireza Doustvandi, Mehrzad Tahamouli Roudsari^*, Behnoush Niazi

Structural Durability & Health Monitoring, Vol.17, No.1, pp. 55-70, 2023, DOI:10.32604/sdhm.2022.017458

Abstract Liquid storage, particularly oil and petrochemical products which are considered hazardous liquid, are an important part of the oil industry. Thin-walled vertical cylindrical steel storage tanks are widely used in recent years. Due to high sensitivity of these structures in an earthquake and other external excitations may lead to catastrophic consequences. For instance, huge economic losses, environmental damages, and casualities, many studies have been done about these structures. past studies showed that liquid storage tanks, equipped with a floating roof, are potentially vulnerable while subjected to seismic loads and earthquake has been considered as one of the most destructive natural… More >

Xiang Zhang^1,*, Miao Su¹, Wenjie Yu², Zhen Lei¹, Jun Ren¹, Juntong Qu¹

CMES-Computer Modeling in Engineering & Sciences, Vol.136, No.2, pp. 1487-1507, 2023, DOI:10.32604/cmes.2023.025799

Abstract The durability of cement-based materials is related to water transport and storage in their pore network under different humidity conditions. To understand the mechanism and characteristics of water adsorption and desorption processes from the microscopic scale, this study introduces different points of view for the pore space model generation and numerical simulation of water transport by considering the “ink-bottle” effect. On the basis of the pore structure parameters (i.e., pore size distribution and porosity) of cement paste and mortar with water-binder ratios of 0.3, 0.4 and 0.5 obtained via mercury intrusion porosimetry, randomly formed 3D pore space models are generated… More >