Dein Shaw^1,2, Chih-Ren Huang², Li-Cheng Huang²

CMC-Computers, Materials & Continua, Vol.11, No.3, pp. 229-242, 2009, DOI:10.3970/cmc.2009.011.229

Abstract In this study, a method for designing an in-plane, free-form, beam-type spring for use in a lower-limb orthosis was developed. A spring designed by this method follows a predefined relationship between loading and displacement. To facilitate the analysis of the spring, it was divided into several beam segments. The stiffness equations related to loading (including moment and force) and displacements (linear and rotation) of each beam segment were found to follow a modified (non-linear) Castigliano's second theorem (NCST) and were assembled by using the continuity of nodal points of neighbouring curve segments. Using the proposed method, a spring designer can… More >

Syh-Tsang Jenq^1,2, Yuen-Sheng Chiu²

CMC-Computers, Materials & Continua, Vol.11, No.1, pp. 33-58, 2009, DOI:10.3970/cmc.2009.011.033

Abstract Current work studies the transient hydroplaning behavior of 200 kPa inflated pneumatic radial tires with various types of tread patterns. Tires were numerically loaded with a quarter car weight of 4 kN, and then accelerated from rest rolling over a water film with a thickness of 5, 10 and 15 mm on top of a flat pavement. Tire structure is composed of outer rubber tread and inner fiber reinforcing composite layers. The Mooney-Rivlin constitutive law and the classical laminated theory (CLT) were, respectively, used to describe the mechanical behavior of rubber material and composite reinforcing layers. The tire hydroplaning phenomenon… More >

P. B. Abhale¹, N. N. Viswanathan¹, N. B. Ballal¹

CMC-Computers, Materials & Continua, Vol.10, No.2, pp. 195-216, 2009, DOI:10.3970/cmc.2009.010.195

Abstract Simulation of gas flow in a multilayered non-isothermal packed bed is useful for blast furnace operators in deciding appropriate charging strategy. While using an anisotropic form of Ergun equation to simulate gas flow through such systems, a new solution methodology for non-isothermal gas with varying density flowing through a layered burden has been proposed. This involves handling non-linearity due to gas density variation with pressure and temperature by solving for the square of pressure instead of pressure directly and handling the non-linearity due to |v| term in the Ergun equation by solving linearized form of Ergun equation and updating |v|… More >

D.W. Kelly¹, M.C.W. Lee¹, A.C. Orifici^2,3, R.S.Thomson³, R. Degenhardt^4,5

CMC-Computers, Materials & Continua, Vol.10, No.2, pp. 163-194, 2009, DOI:10.3970/cmc.2009.010.163

Abstract An experimental program for collapse of curved stiffened composite shell structures encountered a wide range of initial and deep buckling mode shapes. This paper presents work to determine the significance of the buckling deformations for determining the final collapse loads and to understand the source of the variation. A finite element analysis is applied to predict growth of damage that causes the disbonding of stiffeners and defines a load displacement curve to final collapse. The variability in material properties and geometry is then investigated to identify a range of buckling modes and development of deep postbuckling deformation encountered in the… More >

Deepak A Apte¹, Ranjan Ganguli^1,2

CMC-Computers, Materials & Continua, Vol.10, No.2, pp. 139-162, 2009, DOI:10.3970/cmc.2009.010.139

Abstract The influence of electric field and temperature on power consumption of piezoelectric actuated integrated structure is studied by using a single degree of freedom mass-spring-damper system model coupled with a piezoactuator. The material lead zirconate titanate, is considered as it is capable of producing relatively high strains (e.g., 3000με). Actuators are often subject to high electric fields to increase the induced strain produced, resulting in field dependant piezoelectric coefficient d₃₁, dielectric coefficient ε₃₃ and dissipation factor δ. Piezostructures are also likely to be used across a wide range of temperatures in aerospace and undersea operations. Again, the piezoelectric properties can… More >

J. Ghanbari¹, R. Naghdabadi^1,2

CMC-Computers, Materials & Continua, Vol.10, No.1, pp. 41-64, 2009, DOI:10.3970/cmc.2009.010.041

Abstract Continuum-based modeling of nanostructures is an efficient and suitable method to study the behavior of these structures when the deformation can be considered homogeneous. This paper is concerned about multiscale nonlinear tensorial constitutive modeling of carbon nanostructures based on the interatomic potentials. The proposed constitutive model is a tensorial equation relating the second Piola-Kirchhoff stress tensor to Green-Lagrange strain tensor. For carbon nanotubes, some modifications are made on the planar representative volume element (RVE) to account for the curved atomic structure resulting a non-planar RVE. Using the proposed constitutive model, the elastic behavior of the graphene sheet and carbon nanotube… More >

Shen Yubin¹, Xie Huicai^1,2, Den Wei¹

CMC-Computers, Materials & Continua, Vol.3, No.2, pp. 49-54, 2006, DOI:10.3970/cmc.2006.003.049

Abstract Bonding an overlay of new concrete onto the damaged concrete is a usual repair method. Because of the different shrinkage rate of the new and old concrete, restrained shrinkage cracks will appear in the new concrete. The cracks will reduce durability and strength of the repaired structure. A new repair method using an interface layer of carbon fiber reinforced cement mortar between new and old concrete was developed in this paper. The new method was found to be very effective in reducing shrinkage cracking of repaired beams and slabs. Comparing with normal repaired beams, the maximum observed width of the… More >

G. Mishuris¹, A. Öchsner², G. Kuhn³

CMC-Computers, Materials & Continua, Vol.2, No.4, pp. 227-238, 2005, DOI:10.3970/cmc.2005.002.227

Abstract FEM-evaluation of imperfect transmission conditions has been performed for a modelling problem of an elastic structure with a thin intermediate interface. Very good correlations with theoretical results have been obtained. Additionally, the possible error connected with introducing the transmission conditions instead of the intermediate zone has been estimated depending on mechanical properties of the zone. More >