Ligia Munteanu¹, Veturia Chiroiu¹, Viorel Şerban²

CMC-Computers, Materials & Continua, Vol.42, No.3, pp. 175-204, 2014, DOI:10.3970/cmc.2014.042.175

Abstract The paper introduces a new alternative towards fabrication of auxetic metamaterials (materials with negative Poisson’s ratio) controlled by geometric transformations. These transformations are derived from the theory of small (infinitesimal) elastic deformation superimposed on finite elastic deformations. By using this theory, a cylindrical region filled with initial deformed foam is transformed through deformation into a cylindrical shell region filled with auxetic metamaterial. As an example, the realization of the seismic cloak device becomes a practical possibility. More >

K.B. Mustapha ^1,2

CMC-Computers, Materials & Continua, Vol.42, No.2, pp. 141-174, 2014, DOI:10.3970/cmc.2014.042.141

Abstract This study investigates the sensitivity of the flexural response of a ribconnected system of coupled micro-panels with traction-free surfaces. Idealized as a two-dimensional elastic continuum with a finite transverse stiffness, each micropanels’ behavior is examined within the framework of the biharmonic mathematical model derived from the higher-order, size-dependent strain energy formulation. The model incorporates the material length scale, which bears an associative relationship with the underlying polymer’s averaged Frank elastic constant. Upper estimates of the eigenvalue of the system, under fully clamped edges and simplysupported edges, are determined by the Rayleigh method. The adopted theory for the micro-panel’s behavior takes… More >

M. Chang^1,2,3, Y. C. Chou^1,2, P. T. Lin^1,2, J. L. Gabayno^2,4

CMC-Computers, Materials & Continua, Vol.42, No.2, pp. 125-140, 2014, DOI:10.3970/cmc.2014.042.125

Abstract Automated optical inspection systems installed in production lines help ensure high throughput by speeding up inspection of defects that are otherwise difficult to detect using the naked eye. However, depending on the size and surface properties of the products such as micro-cracks on touchscreen panels glass cover, the detection speed and accuracy are limited by the imaging module and lighting technique. Therefore the current inspection methods are still delegated to a few qualified personnel whose limited capacity has been a huge tradeoff for high volume production. In this study, an automated optical technology for in-line surface defect inspection is developed… More >

S. Zhao¹, Zichun Yang^1,2, X. G. Zhou³, X. Z. Ling⁴, L. S. Mora⁵, D. Khoshkhou⁶, J. Marrow⁵

CMC-Computers, Materials & Continua, Vol.42, No.2, pp. 103-124, 2014, DOI:10.3970/cmc.2014.042.103

Abstract Continuous SiC fiber reinforced SiC matrix composites (SiC/SiC) have been studied and developed for high temperature and fusion applications. Polymer impregnation and pyrolysis (PIP) is a conventional technique for fabricating SiC/SiC composites. In this research, KD-1 SiC fibers were employed as reinforcements, a series of coatings such as pyrocarbon (PyC), SiC and carbon nanotubes (CNTs) were synthesized as interphases, PCS and LPVCS were used as precursors and SiC/SiC composites were prepared via the PIP method. The mechanical properties of the SiC/SiC composites were characterized. Relationship between the interphase shear strength and the fracture toughness of the composites was established. X-ray… More >

Amar Prakash¹, Srinivasan, S. M.², Rama Mohan Rao, A.³

CMC-Computers, Materials & Continua, Vol.42, No.1, pp. 75-102, 2014, DOI:10.3970/cmc.2014.042.075

Abstract Behaviour of layered steel fibre reinforced cementitious composite (SFRCC) panels is studied under high velocity impact of short projectiles. The panels consist of slurry infiltrated fibre concrete (SIFCON) layers in external faces and an intermediate (core) layer of latex modified concrete (LMC) and steel wire mesh embedded in cement sand slurry. In order to minimize acoustic impedance mismatch at the interfaces, judiciously selected materials are provided in the layers with appropriate lay-up sequences. For relative evaluation of high velocity impact performances of these panels', impact experiments are conducted in controlled environment. Two most commonly used types of short projectiles having… More >

J. Joseph¹, Y. C. Lu ¹,

CMC-Computers, Materials & Continua, Vol.42, No.1, pp. 63-74, 2014, DOI:10.3970/cmc.2014.042.063

Abstract The super-long, vertically aligned carbon nanotubes (SL-VACNTs) are novel carbon nanomaterial produced from template-free synthesis. The mechanical responses of such material have been investigated by continuum finite element modeling and compared with experimental observations. The crushable foam model has been adequate in modeling the stress-strain curve and deformation of the SL-VACNTs under compression. SL-VACNTs are seen to exhibit transient elastic deformation at small displacement and then plastic deformation at large displacement. The deformation mostly occur at the position immediately beneath the compression platen (indenter face) due to the high stress/strain concentrations. More >

M. Negin¹, S. D. Akbarov^2,3, M. E. Erguven¹

CMC-Computers, Materials & Continua, Vol.42, No.1, pp. 25-62, 2014, DOI:10.3970/cmc.2014.042.025

Abstract Within the framework of the piecewise homogeneous body model the influence of the shear-spring type imperfect contact conditions on the dispersion relation of the generalized Rayleigh waves in the system consisting of the initially stressed covering layer and initially stressed half plane is investigated. The second version of the small initial deformation theory of the three-dimensional linearized theory of elastic waves in initially stressed bodies is applied and the elasticity relations of the materials of the constituents are described by the Murnaghan potential. The magnitude of the imperfectness of the contact conditions is estimated through the shear-spring type parameter. Consequently,… More >

Anna Y. Matveeva¹, Helmut J. Böhm², Grygoriy Kravchenko², Ferrie W. J. van Hattum¹

CMC-Computers, Materials & Continua, Vol.42, No.1, pp. 1-23, 2014, DOI:10.3970/cmc.2014.042.001

Abstract This paper presents a comparison of different finite element approaches to modelling polymers reinforced with wavy, hollow fibres with the aim of predicting the effective elastic stiffness tensors of the composites. The waviness of the tubes is described by sinusoidal models with different amplitude-to-wavelength parameters. These volume elements are discretized by structured volume meshes onto which fibres in the form of independently meshed beam, shell or volume elements are superimposed. An embedded element technique is used to link the two sets of meshes. Reference solutions are obtained from conventional three-dimensional volume models of the same phase arrangements. Periodicity boundary conditions… More >

K. Umesh¹, R. Ganguli¹

CMC-Computers, Materials & Continua, Vol.41, No.3, pp. 215-240, 2014, DOI:10.3970/cmc.2014.041.215

Abstract Fractal dimension based damage detection method is investigated for a composite plate with random material properties. Composite material shows spatially varying random material properties because of complex manufacturing processes. Matrix cracks are considered as damage in the composite plate. Such cracks are often seen as the initial damage mechanism in composites under fatigue loading and also occur due to low velocity impact. Static deflection of the cantilevered composite plate with uniform loading is calculated using the finite element method. Damage detection is carried out based on sliding window fractal dimension operator using the static deflection. Two dimensional homogeneous Gaussian random… More >

Yuvaraj P¹, A Ramachra Murthy², Nagesh R Iyer³, S.K. Sekar⁴, Pijush Samui⁵

CMC-Computers, Materials & Continua, Vol.41, No.3, pp. 193-214, 2014, DOI:10.3970/cmc.2014.041.193

Abstract This paper presents fracture mechanics based Artificial Neural Network (ANN) model to predict the fracture characteristics of high strength and ultra high strength concrete beams. Fracture characteristics include fracture energy (Gf), critical stress intensity factor (KIC) and critical crack tip opening displacement (CTODc). Failure load of the beam (Pmax) is also predicated by using ANN model. Characterization of mix and testing of beams of high strength and ultra strength concrete have been described. Methodologies for evaluation of fracture energy, critical stress intensity factor and critical crack tip opening displacement have been outlined. Back-propagation training technique has been employed for updating… More >