S. Liu¹, X. Liu^2,3, Y. Yuan², P. F. He¹, H. A. Mang^2,4

CMC-Computers, Materials & Continua, Vol.39, No.2, pp. 85-112, 2014, DOI:10.3970/cmc.2014.039.085

Abstract Autogenous shrinkage is defined as the bulk deformation of a closed, isothermal, cement-based material system, which is not subjected to external forces. It is associated with the hydration process of the cement paste. From the viewpoint of engineering practice, autogenous shrinkage deformations result in an increase of tensile stresses, which may lead to cracking of early-age concrete. Since concrete is a multi-phase composite with different material compositions and microscopic configurations at different scales, autogenous shrinkage does not only depend on the hydration of the cement paste, but also on the mechanical properties of the constituents and of their distribution. In… More >

Jingguo Yan¹, Xudong Wang¹, Man Yao^1,2, Ning Hu^3,4

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 73-84, 2014, DOI:10.3970/cmc.2014.039.073

Abstract Electronic structure and magnetism of the rare-earth metals Ac and Th doped Fe₃O₄ Fe_1-xRe_xFe_2-yRe_yO₄(Re=Ac, Th; x=0, 0.5, 1; y=0, 0.5, 1.0, 1.5, 2.0) are investigated by first-principle calculations. AcFe₂O₄, FeAc₂O₄ and ThFe₂O₄ are found to be II B-type half-metals. The large bonding-antibonding splitting is believed to be the origin of the gap for AcFe₂O₄, FeAc₂O₄ and ThFe₂O₄, resulting in a net magnetic moment of 9.0μ_B, 4.0μ_B and 8.1μ_B, respectively, compared with 4.0μ_B of Fe₃O₄. Also, the conductance of AcFe₂O₄ and ThFe₂O₄ are both slightly larger than that of Fe3O4. It can be predicted that the new rare-earth half-metals AcFe₂O₄ and… More >

Y.C. Shiah¹, Y.M. Lee², T.C. Huang²

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 49-71, 2014, DOI:10.3970/cmc.2014.039.049

Abstract A common difficulty arises in characterizing the anisotropic properties of a thin sheet of anisotropic material, especially in the transverse direction. This difficulty is even more phenomenal for measuring its mechanical properties on account of its thickness. As the prelude of such investigation, this paper proposes a novel approach to identify the thermal conductivities of an unknown thin layer of anisotropic material. For this purpose, the unknown layer is sandwiched in isotropic materials with known conductivities. Prescribing proper boundary conditions, one may easily measure temperature data on a few sample boundary points. Therefore, the anisotropic thermal conductivities can be calculated… More >

J. Aubry¹, P. Navarro¹, S. Marguet¹, J.-F. Ferrero¹, O. Dorival², L. Sohier³, J.-Y. Cognard³

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 21-47, 2014, DOI:10.3970/cmc.2014.039.021

Abstract In this paper a numerical model dedicated to the simulation of the mechanical behaviour of polymeric Rohacell foams is presented. The finite elements model is developed at the scale of the microstructure idealized by a representative unit cell: the truncated octahedron. Observations made on micrographs of Rohacell lead to mesh this representative unit cell as a lattice of beam elements. Each beam is assigned a brittle linear elastic mechanical behaviour in tension and an elastoplastic behaviour in compression. The plasticity in compression is introduced as a way to mimic the buckling of the edges of the cells observed in experimental… More >

Meng-Kao Yeh¹, Chia-Shien Liu², Chien-Chang Chen³

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 3-20, 2014, DOI:10.3970/cmc.2014.039.003

Abstract The dynamic instability of rectangular graphite/epoxy composite plates under parametric excitation was investigated analytically and experimentally. In analysis, the dynamic system of the composite plate, obtained based on the assumedmodes method, is a general form of Mathieu’s equation, including parametrically excited terms. The instability regions of the system, each separated by two transition curves, were found to be functions of the modal parameters of the composite plate and the position and the excited amplitude of the electromagnetic device on the composite plates. The fiber orientation, the aspect ratio and the layer numbers of the composite plates were varied to assess… More >

Satya N. Atluri¹

CMC-Computers, Materials & Continua, Vol.39, No.1, pp. 1-2, 2014, DOI:10.3970/cmc.2014.039.001

Abstract This article has no abstract. More >

J.B. Niu¹, L.L. Li², Q. Xu¹, Z.H. Xia^1,3

CMC-Computers, Materials & Continua, Vol.38, No.1, pp. 31-41, 2013, DOI:10.3970/cmc.2013.038.031

Abstract Crack deflection and penetration at the interface of multi-wall carbon nanotube/amorphous carbon composites were studied via molecular dynamics simulations. In-situ strength of double-wall nanotubes bridging a matrix crack was calculated under various interfacial conditions. The structure of the nanotube reinforcement -ideal multi-wall vs. multi-wall with interwall sp³ bonding - influences the interfacial sliding and crack penetration. When the nanotube/matrix interface is strong, matrix crack penetrates the outermost layer of nanotubes but it deflects within the nanotubes with certain sp³ interwall bond density, resulting in inner wall pullout. With increasing the sp³ interwall bond density, the fracture mode becomes brittle; the… More >

X. Frank Xu^1,2, Yuxin Jie³, Irene J. Beyerlein⁴

CMC-Computers, Materials & Continua, Vol.38, No.1, pp. 17-30, 2013, DOI:10.3970/cmc.2013.038.017

Abstract This note aims to relate the measured strength statistics of individual carbon nanotubes (CNTs) to the physics of brittle fracture and the weakest link model. By approximating an arbitrary flaw size distribution with a segmented power law, an effort is made to extend applicability of the Weibull distribution to arbitrary flaw populations, which explains why the Weibull distribution fits the experimental data of CNTs and many other brittle materials, and why in other cases it is not so clear. A generalized Weibull distribution is proposed to account for all non-asymptotic cases. The published CNT testing data are analyzed, and finally… More >

Branden B. Kappes¹, Cristian V. Ciobanu²

CMC-Computers, Materials & Continua, Vol.38, No.1, pp. 1-16, 2013, DOI:10.3970/cmc.2013.038.001

Abstract Controlling the bandgap of carbon nanostructures is a key factor in the development of mainstream applications of carbon-based nanoelectronic devices. This is particularly important in the cases where it is desired that the carbon nanostructures are the active elements, as opposed to being the conductive leads between other elements of the device. Here, we report density functional theory calculations of the effect of silicon impurities on the electronic properties of carbon nanotubes (CNTs). We have found that Si adatoms can open up a bandgap in intrinsically metallic CNTs, even when the linear density of Si atoms is low enough that… More >

Yongze Cao¹, Guojian Li¹, Qiang Wang^1,2, Xiaoguang Wang³, Jiaojiao Du¹, Jicheng He¹

CMC-Computers, Materials & Continua, Vol.37, No.3, pp. 195-203, 2013, DOI:10.3970/cmc.2013.037.195

Abstract The Fe₆₀Ni₄₀ (in atomic %) polycrystalline thin films with 90 nm thickness were prepared on 200 °C quartz substrate by using molecular beam vapor deposition method. The influence of 0 T and 6 T magnetic fields on the structural evolution and magnetic properties of thin films was studied by using EDXS, XRD, AFM and VSM. In this study, only α phase was formed in both thin films. It was found that the application of a 6 T magnetic field obviously decreases the RMS of surface roughness and the grain size. For the magnetic properties of the thin films, the 6… More >