GAURAV AGARWAL

Journal of Polymer Materials, Vol.39, No.3-4, pp. 255-267, 2022, DOI:10.32381/JPM.2022.39.3-4.6

Abstract Studies were conducted to observe the effect of fracture toughness and damping response on fabric reinforced epoxy polymer composites. The samples of glass fabric, kevlar fabric and carbon fabric having 15wt%, 25wt%, 35wt%, 45wt% and 55wt % fabric content were prepared and tested following ASTM standards. Fracture toughness, peak load and increase in energy absorption are determined for the fabric-epoxy composites. Effect of temperature on storage modulus, loss modulus and tan delta values for various percentages of fabric epoxy composites are noticed and corresponding damping response behaviour is determined. The results revealed that reduction in More >

MUHAMAD SOFFI BIN MANDA^1,2, MOHD RUZAIMI BIN MAT REJAB¹, SHUKUR ABU HASSAN^3,4, MAT UZIR BIN WAHIT^3,4, JOSEPH SELVI BINOJ^5,*, BRIGHT BRAILSON MANSINGH⁶, SITI SAFARAH BINTI AMIRNUDDIN³, ALAMRY ALI⁷, KHENG LIM GOH^8,9, DIDIK NURHADIYANTO¹⁰

Journal of Polymer Materials, Vol.39, No.3-4, pp. 241-253, 2022, DOI:10.32381/JPM.2022.39.3-4.5

Abstract This study investigates the potential of Tin Slag Polymer Concrete (TSPC) strengthening through confinement using basalt fiber reinforced polymer (BFRP) and aramid fiber reinforced polymer (AFRP) confinement. TSPC short cylindrical column samples have been wrapped with BFRP and AFRP in a single layer (30 mm overlap) using Sikadur-330 epoxy and final samples were coded as TSPC-UC, TSPC-BF and TSPC-AF for unconfined, BFRP and AFRP for confined respectively. After curing for 30 days at room temperature, compressive test has been performed to know the strength, modulus, strain, fracture energy and failure modes of unconfined and confined… More >

RITESH D. BHATT, JIGNESH P. PATEL, PARSOTAM H. PARSANIA^*

Journal of Polymer Materials, Vol.39, No.3-4, pp. 223-239, 2022, DOI:10.32381/JPM.2022.39.3-4.4

Abstract Compression-molded epoxy methacrylate of bisphenol-C-jute/treated jute-banana/groundnut/ cane sugar/pineapple leaf/rice husk/wheat husk sandwich composites were fabricated under 5 MPa pressure at room temperature for 3 h. Alkali treated jute-natural fiber sandwich composites displayed considerably improved mechanical properties over untreated jute-natural fiber sandwich composites due to surface modification of the jute fibers. Both types of sandwich composites showed high water uptake tendency, excellent hydrolytic stability against acids, alkali, and salt solutions, and also a longer equilibrium time at 30o C. Alkali treated sandwich composites revealed a considerably lower water uptake tendency than untreated sandwich composites. Observed water More >

RITESH D. BHATT, JIGNESH P. PATEL, PARSOTAM H. PARSANIA^*

Journal of Polymer Materials, Vol.39, No.3-4, pp. 205-221, 2022, DOI:10.32381/JPM.2022.39.3-4.3

Abstract Epoxy methacrylate of bisphenol-C-jute/treated jute and their sandwich composites of white coir, brown coir, wild almond, bamboo, betel nut, and palmyra were prepared by a compression molding technique under 5MPa pressure and at room temperature for three h. The neat sample showed almost double tensile strength than its jute composite, while it is comparable for treated jute. The composites revealed substantially improved flexural strength compared to neat. The neat, jute/treated jute and their sandwich composites indicated good impact strength, pretty good Barcol hardness, and fairly good electric strength. The neat sample showed excellent volume resistivity, More >

S. MATHIVANAN^*, R. MOHAN, RAMES C PANDA, P. BALACHANDER¹

Journal of Polymer Materials, Vol.39, No.3-4, pp. 195-204, 2022, DOI:10.32381/JPM.2022.39.3-4.2

Abstract Optimum-designed footwear with polyurethane (PU) material for comfort is an important requirement for obese. Investigations on compressive behavior of varied designed footwear using 120 D PU material have been carried out. The energy absorption primarily depends on heel height, slope angle and load applied or body mass index of obese. Statistical analysis has been used to formulate the prediction of absorbed energy wherein a heel height of 30 mm with 20-degree angle provides optimum value with the incorporation of 120 D PU material. A coefficientof-determination (R² ) value of 0.9406 confirms the suitability of the statistical More >

ALOK K. SAHU^a, RAJSHREE VIJAYVARGIYA^a, R. M. SARVIYA^b

Journal of Polymer Materials, Vol.39, No.3-4, pp. 183-193, 2022, DOI:10.32381/JPM.2022.39.3-4.1

Abstract HDPE material is found to be best suited material for the manufacturing of floating bed structure for the solar photovoltaic (PV) system due to its light weight and excellent mechanical & chemical resistant properties. However, the major restriction in this regard is the limited engineering design and also the effect of UV radiations present in the natural environment that leads to the degradation of the plastic materials. Hence, in order to improve its UV stability carbon black is incorporated into it as UV resistant additive and hollow cubical floats of such HDPE/carbon black composite material… More >

XINGMIN XU¹, QINGQING SUN², AIRONG XU², XINBAO GUO²

Journal of Polymer Materials, Vol.39, No.1-2, pp. 167-181, 2022, DOI:10.32381/JPM.2022.39.1-2.11

Abstract Silk fibroin (SF) with renewability, biocompatibility and biodegradability shows potential application in various fields including biomedicine, tissue engineering, and wearable electronic devices. Herein, SF is used to exert effective reinforcement of polyvinyl alcohol (PVA) composite film to further improve its practicability. As such, PVA/SF composite films were prepared for the first time using a facile approach. The films were characterized to investigate possible interaction of PVA with SF. Meanwhile, systematic investigations have also been completed to explore the influences of PVA/SF mass ratio on the mechanical properties (tensile strength, elongation at break), biodegradability and biocompatibility, More >

NURUL HAYATI YUSOF^1,*, DAZYLAH DARJI¹, TAN KIM SONG¹, NGHIEM THI THUONG²

Journal of Polymer Materials, Vol.39, No.1-2, pp. 151-166, 2022, DOI:10.32381/JPM.2022.39.1-2.10

Abstract In this work, a pure gum mould made of prevulcanized natural rubber/cloisite-Na⁺ nanocomposite (PVNR/CN) was prepared and characterized for ornament application. The suitable conditions to prepare PVNR/CN latex mixtures and the properties of the resulting PVNR/CN nanocomposites were investigated. The optimum CN concentration in the latex mixture was 1.0 phr, with the properties of 60 wt% total solid content, more than 600 sec mechanical stability time, lower than 350 cP Brookfield viscosity, and pH 10. The properties of PVNR/CN nanocomposite showed high strength, moderate hardness, and good thermal stability. The morphology by TEM showed well dispersion More >

V. S. MAMTANI, A. K. GHOSH^*, R. C. BINDAL

Journal of Polymer Materials, Vol.39, No.1-2, pp. 137-149, 2022, DOI:10.32381/JPM.2022.39.1-2.9

Abstract In this study, polysulfone based capillary ultrafiltration membranes with desired characteristics were indigenously developed and their performance was evaluated with respect to turbidity removal from raw sea water. Capillary membranes were spun with in-house fabricated spinneret using polymer casting solution (dope solution) of different compositions having different viscosity using polyvinyl pyrrolidone (PVP) as pore-forming agent. Different experimental conditions namely dope pressure, bore fluid flow rate and air gap distance are optimized to get membranes of desired properties. Test results of individual capillaries in terms of pure water permeability (PWP), separation of single uncharged solutes like… More >

PRABHAT KUMAR, ANJANA SARKAR, PURNIMA JAIN^*

Journal of Polymer Materials, Vol.39, No.1-2, pp. 121-135, 2022, DOI:10.32381/JPM.2022.39.1-2.8

Abstract Biocompatible graphene derivative materials (GBMs) to harness the maximum potential of pristine graphene biologically, is the most important strategy for its advanced applications in pharmaceutical and other biomedical fields. Currently, scientists are trying to find this by using biopolymer nanocomposites or anchored materials. Nevertheless, tuning the bare GBMs towards biocompatibility is a beautiful approach to exploit the fundamental potential of pristine graphene vis-à-vis suppressing the effects of incorporated biopolymers or anchored materials. Herein, a large-scale, cost-effective, facile, and environment-friendly green synthetic strategy is used for the synthesis of reduced graphene oxide (rGO) nanosheet using L-ascorbic… More >