Xuefeng Song^*, Minjuan Sun, Juan He, Lei Wang

Journal of Renewable Materials, Vol.11, No.12, pp. 4079-4095, 2023, DOI:10.32604/jrm.2023.028885 - 10 November 2023

Abstract The adsorption method has the advantages of low cost, high efficiency, and environmental friendliness in treating fluorinated wastewater, and the adsorbent material is the key. This study combines the inherent anion-exchange adsorption properties of layered double hydroxides (LDHs). Self-supported porous adsorbent materials loaded with AFm and AFt were prepared from a composite cementitious system consisting of calcium aluminate cement (CAC) and flue gas desulfurization gypsum (FGDG) by chemical foaming technique. The mineral composition of the adsorbent material was characterized by X-ray diffraction (XRD) and Scanning electron microscopy (SEM). Through the static adsorption experiment, the adsorption… More > Graphic Abstract

Ye Fu¹, Liwen Deng^1,*, Jinbo Hu^2,3,*, Ti Li³, Shanshan Chang²

Journal of Renewable Materials, Vol.11, No.12, pp. 4025-4038, 2023, DOI:10.32604/jrm.2023.028454 - 10 November 2023

Abstract In the study, it is proposed that a coordinate-parametric matrix model is performed to a square-conjoint pattern of cross woven (SCPCW) in the bamboo mat. The patterns of SCPCW are firstly detected according to the perspective of configuration, which is divided into the basic-monomer shape and the basic combination shape. Secondly, the compositions of design patterns in SCPCW are analyzed to attain the trend of curve shape. Based on the coordinate-parametric matrix model, the specimens of SCPCW are subsequently accomplished to elaborate the woven logic of bamboo mats. The digital innovation of SCPCW, defined by More > Graphic Abstract

Hu Shi, Wei Cai, Xin Wang^*, Lei Song, Yuan Hu^*

Journal of Renewable Materials, Vol.11, No.12, pp. 3991-4006, 2023, DOI:10.32604/jrm.2023.029888 - 10 November 2023

Abstract To solve the fire accidents caused by coal combustion, this work prepared four hybrid hydrogel materials using bio-based polymers, flame retardants, and inorganic materials. Compared to pure water and 3.5 wt% MgCl₂ solution, the as-prepared hydrogel presents good fire prevention performance. In addition, it is found that CO and CO₂ are not produced by coal when the pyrolysis temperature is lower than 200°C. During low-temperature pyrolysis, CO is more likely to be produced than CO₂, indicating inadequate pyrolysis behavior. At the same time, the addition of fire-preventing hydrogel can not only decrease the maximum CO₂ concentration before… More > Graphic Abstract

Suprapto Suprapto, Putri Augista Nur Azizah, Yatim Lailun Ni’mah^*

Journal of Renewable Materials, Vol.11, No.12, pp. 4007-4023, 2023, DOI:10.32604/jrm.2023.031210 - 10 November 2023

Abstract This research focuses on the effective removal of methylene blue dye using silica gel synthesized from chemical glass bottle waste as an environmentally friendly and cost-effective adsorbent. The adsorption process was optimized using Box-Behnken Design (BBD) and Response Surface Methodology (RSM) to investigate the influence of pH (6; 8 and 10), contact time (15; 30 and 45 min), adsorbent mass (30; 50 and 70 mg), and initial concentration (20; 50 and 80 mg/L) of the adsorbate on the adsorption efficiency. The BBD was conducted using Google Colaboratory software, which encompassed 27 experiments with randomly assigned… More > Graphic Abstract

Henky Muljana^*, Ivana Hasjem, Merianawati Sinatra, Dicky Joshua Pesireron, Michael Wilbert Puradisastra, Ryan Hartono, Kevin Yovan Hermanto, Tony Handoko

Journal of Renewable Materials, Vol.11, No.12, pp. 4039-4060, 2023, DOI:10.32604/jrm.2023.031261 - 10 November 2023

Abstract This research paper describes the synthesis of thermo-reversible cross-linking of sago starch by grafting a furan pendant group (methyl 2-furoate) onto the starch backbone, followed by a Diels-Alder (DA) reaction of the furan functional group with 1,1′-(methylenedi-4,1-phenylene) bismaleimide (BM). The proof of principles was provided by FTIR and ¹H-NMR analyses. The relevant FTIR peaks are the carbonyl peak (υ C=O sym) at 1721 cm⁻¹ ; the two peaks appeared after DA cross-linking, i.e., at 1510 cm⁻¹ (corresponding to υ CH=CH BM aromatic rings, stretching vibrations), and at 1173 cm⁻¹ (assigned to cycloadduct (C-O-C, δ DA ring)) while More > Graphic Abstract

Demiao Chu¹, Redžo Hasanagić², Leila Fathi³, Mohsen Bahmani^3,*, Miha Humar⁴

Journal of Renewable Materials, Vol.11, No.12, pp. 4061-4078, 2023, DOI:10.32604/jrm.2023.043657 - 10 November 2023

Abstract This study aimed to investigate the water absorption capacity of thermally modified and non-modified spruce and blue-stained spruce wood. The wettability of wood depends on various factors, including its type, density, porosity, and surface treatment. Wood can swell and become distorted when exposed to water or humidity, impacting its structural integrity. Hence, it is crucial to consider the water and water vapour uptake in the wood when choosing materials for applications that are likely to be exposed to moisture. Various moisture absorption tests were conducted to assess water absorption capacity, including short-term and long-term water… More > Graphic Abstract

Adekunle A. Adeleke^1,*, Nzerem Petrus², Salihu Ayuba², Asmau M. Yahya², Peter P. Ikubanni³, Ikechuckwu S. Okafor², Stephen S. Emmanuel⁴, Adebayo I. Olosho⁴, Ademidun A. Adesibikan⁴

Journal of Renewable Materials, Vol.11, No.12, pp. 4123-4141, 2023, DOI:10.32604/jrm.2023.043915 - 10 November 2023

Abstract Nigeria, often referred to as “the giant of Africa,” boasts a sizable population, a thriving economy, and abundant energy resources. Nevertheless, Nigeria has yet to fully harness its renewable energy potential, despite its enormous capacity in this field. The goal of this review paper is to thoroughly examine the difficulties and untapped opportunities in utilizing biomass for bioenergy production in Nigeria. Notably, Nigeria generates substantial volumes of biomass annually, primarily in the form of agricultural waste, which is often either discarded or burned inefficiently, resulting in significant ecological and environmental damage. Therefore, an efficient approach… More > Graphic Abstract

Ying Ji^*, Xi Liu^*

Journal of Renewable Materials, Vol.11, No.11, pp. 3977-3989, 2023, DOI:10.32604/jrm.2023.028439 - 31 October 2023

Abstract The problem of low disposal and utilization rate of bulk industrial solid waste needs to be solved. In this paper, a high-activity admixture composed of steel slag-phosphate slag-limestone powder was proposed for most of the solid waste with low activity and a negative impact on concrete workability, combining the characteristics of each solid waste. The paper demonstrates the feasibility and explains the principle of the composite system in terms of water requirement of standard consistency, setting time, workability, and mechanical properties, combined with the composition of the phases, hydration temperature, and microscopic morphology. The results… More > Graphic Abstract

Guiwu Lin, Kaige Liu, Yuliang Chen^*, Yunpeng Ji, Rui Jiang

Journal of Renewable Materials, Vol.11, No.11, pp. 3957-3975, 2023, DOI:10.32604/jrm.2023.028290 - 31 October 2023

Abstract This paper presents an experimental study to explore the compressive properties of fiber recycled aggregate concrete. A total of 75 specimens with the replacement rate of recycled coarse aggregate and fiber type were conducted under a uniaxial compressive test. The failure modes, stress-strain whole curves, peak stress, peak strain, and energy dissipation capacity were systematically observed and revealed. Test results indicate that steel fiber has the best modification effect on energy dissipation capacity and the toughness index of recycled concrete, corresponding to the enhancement of 81.75% and 22.90% on average. The addition of polyvinyl alcohol… More > Graphic Abstract

Cheng Hu^1,2, Weiheng Xiang^1,3,*, Ping Chen^2,3, Yi Yang^4,5, Libo Zhou³, Jiufang Jiang⁵, Shunkai Li^2,4, Yang Ming¹, Qing Li³

Journal of Renewable Materials, Vol.11, No.11, pp. 3945-3956, 2023, DOI:10.32604/jrm.2023.027544 - 31 October 2023

Abstract The aim of this study is to enhance the value and utilization of red mud generated in the Bayer process by preparing composite cement mortars. The effects of two different types of Bayer red mud with varying physical and chemical characteristics on the fluidity, mechanical strength, mineral composition, and microstructure of the composite cement mortar were systematically evaluated. The results showed that the optimal addition of red mud A was 10 wt%, while it was 20 wt% for red mud B. The mechanical properties of the composite cement mortar met the standards for P·O42.5 cement. More >