Jennifer D. Rhymer¹, Hyonny Kim¹

CMC-Computers, Materials & Continua, Vol.35, No.2, pp. 87-117, 2013, DOI:10.3970/cmc.2013.035.087

Abstract Polymer matrix composite structures are exposed to a variety of impact threats including hail ice. Internal delamination damage created by these impacts can exist in a form that is visually undetectable. This paper establishes an analysis methodology for predicting the onset of delamination damage in toughened carbon/epoxy composite laminates when impacted by high velocity ice spheres (hailstones). Experiments and analytical work focused on ice sphere impact onto composite panels have determined the failure threshold energy as a function of varying ice diameter and panel thickness, and have established the ability to predict the onset of delamination using cohesive elements in… More >

M. C. Song¹, B.V. Sankar¹, G. Subhash¹, C. F. Yen²

CMC-Computers, Materials & Continua, Vol.35, No.1, pp. 67-85, 2013, DOI:10.3970/cmc.2013.035.067

Abstract Delamination initiation and propagation in plain woven laminates and 3D orthogonal woven composites during short beam shear (SBS) test were analyzed using finite element (FE) analyses. Two kinds of 3D woven composites, containing single z-yarns and double z-yarns, were considered. The FE models were guided by experimental observations from SBS tests for the same material systems. A series of mechanisms including creation and evolution of matrix cracks and delaminations were modeled discretely. The force-displacement curves obtained from the FE simulations were compared with those from experiments. Further parametric studies were conducted to investigate the effects of z-yarns and interlaminar fracture… More >

A. Ataş¹, C. Soutis²

CMC-Computers, Materials & Continua, Vol.34, No.3, pp. 199-226, 2013, DOI:10.3970/cmc.2013.034.199

Abstract A strength prediction method is presented for double-lap single fastener bolted joints of cross-ply carbon fibre reinforced plastic (CFRP) composite laminates using cohesive zone elements (CZEs). Three-dimensional finite element models were developed and CZEs were inserted into subcritical damage planes identified from X-ray radiographs. The method makes a compromise between the experimental correlation factors (dependant on lay-up, stacking sequence and joint geometry) and three material properties (fracture energy, interlaminar strength and nonlinear shear stress-strain response). Strength of the joints was determined from the predicted load-displacement curves considering sub-laminate and plylevel scaling effects. The predictions are in a reasonable agreement with… More >

Chih-Wen Chang^1,2, Chein-Shan Liu³

CMC-Computers, Materials & Continua, Vol.34, No.2, pp. 143-175, 2013, DOI:10.3970/cmc.2013.034.143

Abstract The nonlinear Poisson problems in heat diffusion governed by elliptic type partial differential equations are solved by a modified globally optimal iterative algorithm (MGOIA). The MGOIA is a purely iterative method for searching the solution vector x without using the invert of the Jacobian matrix D. Moreover, we reveal the weighting parameter αc in the best descent vector w = αcE + DTE and derive the convergence rate and find a criterion of the parameter γ. When utilizing αc and γ, we can further accelerate the convergence speed several times. Several numerical experiments are carefully discussed and validated the proposed… More >

L.H. Kuo¹, M.H. Gu², D.L. Young³, C.Y. Lin³

CMC-Computers, Materials & Continua, Vol.33, No.3, pp. 213-228, 2013, DOI:10.3970/cmc.2013.033.213

Abstract Coupled with the Houbolt method, a third order finite difference time marching scheme, the method of approximate particular solutions (MAPS) has been applied to solve wave equations. Radial basis function has played an important role in the solution process of the MAPS. To show the effectiveness of the MAPS, we compare the results with the well known Kansa's method, timemarching method of fundamental solutions (TMMFS), and traditional finite element methods. To validate the effectiveness and easiness of the MAPS, four numerical examples which including regular, smooth irregular, and non-smooth domains are given. More >

A Rama Chandra Murthy¹, Smitha Gopinath^1,2, Ashish Shrivastav¹, G. S. Palani¹, Nagesh R. Iyer¹

CMC-Computers, Materials & Continua, Vol.25, No.1, pp. 1-18, 2011, DOI:10.3970/cmc.2011.025.001

Abstract This paper presents methodologies for crack growth study and fatigue remaining life prediction of reinforced concrete structural components accounting for the corrosion effects. Stress intensity factor (SIF) has been computed by using the principle of superposition. At each incremental crack length, net SIF has been computed as the difference of SIF of plain concrete and reinforcement. The behaviour of reinforcement has been considered as elasto-plastic. Uniform corrosion rate has been assumed in the modeling. Corrosion effect has been accounted in the form of reduction in the diameter and modulus of elasticity of steel. Numerical studies have been carried out to… More >

Surkay D. Akbarov^1,2, Arzu Turan³

CMC-Computers, Materials & Continua, Vol.24, No.3, pp. 257-270, 2011, DOI:10.3970/cmc.2011.024.257

Abstract The influence of the initial finite stretching or compressing of the strip containing a single crack on the Energy Release Rate (ERR) and on the SIF of mode I at the crack tips is studied by the use of the Three-Dimensional Linearized Theory of Elasticity. It is assumed that the edges of the crack are parallel to the face planes of the strip and the ends of the strip are simply supported. The initial finite strain state arises by the uniformly distributed normal forces acting at the ends of the strip. The additional normal forces act on the edges of… More >

A. M. Dongare^1,2, A. M. Rajendran³, B. LaMattina⁴, M. A. Zikry¹, D. W. Brenner¹

CMC-Computers, Materials & Continua, Vol.24, No.1, pp. 43-60, 2011, DOI:10.3970/cmc.2011.024.043

Abstract Large-scale molecular dynamics (MD) simulations are used to investigate the effects of microstructure and loading conditions on the dynamic failure behavior of nanocrystalline Cu. The nucleation, growth, and coalescence of voids is investigated for the nanocrystalline metal with average grain sizes ranging from 6 nm to 12 nm (inverse Hall-Petch regime) for conditions of uniaxial expansion at constant strain rates ranging from 4x107 s - 1 to 1010 s - 1. MD simulations suggest that the evolution of voids can be described in two stages: The first stage corresponds to the nucleation of voids and the fast linear initial growth… More >

F. Casciati¹, S. Casciati², L. Faravelli¹, A. Marzi¹

CMC-Computers, Materials & Continua, Vol.23, No.3, pp. 287-306, 2011, DOI:10.3970/cmc.2011.023.287

Abstract The potential offered by the main features of shape memory alloys (SMA) in Structural Engineering applications is object of attention since two decades. The main issues concern the predictability of the material behavior and the fatigue lifetime of macro structural elements (as different from wire segments). In this paper, the fatigue characteristics, at given temperatures, of multigrain samples of a specific Cu-based alloy are investigated. The results of laboratory tests on bar specimens are discussed. The target is to model the manner in which the effects of several loading-unloading cycles of different amplitude cumulate. More >

Hong-Hua Dai^1,2, Jeom Kee Paik³, S. N. Atluri²

CMC-Computers, Materials & Continua, Vol.23, No.2, pp. 155-186, 2011, DOI:10.3970/cmc.2011.023.155

Abstract The application of the Galerkin method, using global trial functions which satisfy the boundary conditions, to nonlinear partial differential equations such as those in the von Karman nonlinear plate theory, is well-known. Such an approach using trial function expansions involving multiple basis functions, leads to a highly coupled system of nonlinear algebraic equations (NAEs). The derivation of such a system of NAEs and their direct solutions have hitherto been considered to be formidable tasks. Thus, research in the last 40 years has been focused mainly on the use of local trial functions and the Galerkin method, applied to the piecewise… More >