V.G.Yakhno¹

CMC-Computers, Materials & Continua, Vol.21, No.1, pp. 1-16, 2011, DOI:10.3970/cmc.2011.021.001

Abstract Homogeneous non-dispersive anisotropic materials, characterized by a positive constant permeability and a symmetric positive definite conductivity tensor, are considered in the paper. In these anisotropic materials, the electric and magnetic dyadic Green's functions are defined as electric and magnetic fields arising from impulsive current dipoles and satisfying the time-dependent Maxwell's equations in quasi-static approximation. A new method of deriving these dyadic Green's functions is suggested in the paper. This method consists of several steps: equations for electric and magnetic dyadic Green's functions are written in terms of the Fourier modes; explicit formulae for the Fourier modes of dyadic Green's functions… More >

X. H. Du¹, X. P. Shen¹

CMC-Computers, Materials & Continua, Vol.20, No.3, pp. 225-242, 2010, DOI:10.3970/cmc.2010.020.225

Abstract Aim of this paper is to estimate the integrity of liquefied natural gas (LNG) prestressed storage tank under seismic influence. The coupled Eulerian-Lagrangian (CEL) analysis technique is used to simulate the fluid-structure interaction between LNG and the cylinder of LNG prestressed storage tank. The 3-D model of LNG has been dispersed by Eulerian mesh that is different from traditional analysis method which is called the added mass method. Meanwhile, both of the 3-D models of prestressed rebar and concrete structure are dispersed by Lagrangian mesh. Following conclusions are obtained: 1) Natural frequency of the whole model has been obtained by… More >

Alamusi¹, Y.L. Liu¹, N. Hu^1,2

CMC-Computers, Materials & Continua, Vol.20, No.2, pp. 101-118, 2010, DOI:10.3970/cmc.2010.020.101

Abstract In this work, we propose a 3 dimensional (3D) numerical model to predict the piezoresistivity behaviors of a nanocomposite material made from an insulating polymer filled by carbon nanotubes (CNTs). This material is very hopeful for its application in highly sensitive strain sensor by measuring its piezoresistivity, i.e., the ratio of resistance change versus applied strain. In this numerical approach, a 3D resistor network model is firstly proposed to predict the electrical conductivity of the nanocomposite with a large amount of randomly dispersed CNTs under the zero strain state. By focusing on the fact that the piezoresistivity of the nanocomposite… More >

Adel A. Abdel-Wahab¹, Angelo Maligno¹, Vadim V. Silberschmidt¹

CMC-Computers, Materials & Continua, Vol.19, No.3, pp. 217-238, 2010, DOI:10.3970/cmc.2010.019.217

Abstract Bone is the principal structural component of a skeleton: it assists the load-bearing framework of a living body. Structural integrity of this component is important; understanding of its mechanical behaviour up to failure is necessary for prevention and diagnostic of trauma. In dynamic events such as traumatic falls, involvement in car crash and sports injuries, bone can be exposed to loads exceeding its structural strength and/or fracture toughness. By developing adequate numerical models to predict and describe its deformation and fracture behaviour up to fracture, a detailed study of reasons for, and ways to prevent or treatment methods of, bone… More >

A.Z. Lorbiecka¹, B. Šarler^1,2

CMC-Computers, Materials & Continua, Vol.18, No.1, pp. 69-104, 2010, DOI:10.3970/cmc.2010.018.069

Abstract The aim of this paper is simulation of thermally induced liquid-solid dendritic growth in two dimensions by a coupled deterministic continuum mechanics heat transfer model and a stochastic localized phase change kinetics model that takes into account the undercooling, curvature, kinetic and thermodynamic anisotropy. The stochastic model receives temperature information from the deterministic model and the deterministic model receives the solid fraction information from the stochastic model. The heat transfer model is solved on a regular grid by the standard explicit Finite Difference Method (FDM). The phase-change kinetics model is solved by the classical Cellular Automata (CA) approach and a… More >

Zone-Ching Lin¹and Ren-Yuan Wang¹

CMC-Computers, Materials & Continua, Vol.16, No.3, pp. 247-272, 2010, DOI:10.3970/cmc.2010.016.247

Abstract The paper establishes a new three-dimensional quasi-steady molecular statics nanoscale abrasive cutting model to investigate the abrasive cutting behavior in the downpressing and abrasive cutting process of a workpiece in chemical mechanical polishing (CMP) process. The downpressing and abrasive cutting process is a continuous process. The abrasive cutting process is done after the single abrasive particle has downpressed and penetrated a workpiece to a certain depth of a workpiece. The paper analyzes the effects of the abrasive particles with different diameters on action force. It also analyzes the action force change of abrasive particles with different diameters on the projected… More >

Chen Y J^1,2, Huber N^2,3

CMC-Computers, Materials & Continua, Vol.16, No.1, pp. 1-24, 2010, DOI:10.3970/cmc.2010.016.001

Abstract An efficient wear integration algorithm is crucial for the simulation of wear in complex transient contact situations. By rewriting Archard's wear law for two dimensional problems, the wear integration can be replaced by the total contact force. This avoids highly resolved simulations in time and space, so that the proposed method allows a significant acceleration of wear simulations. All quantities, including the average contact velocity, slip rate and total contact force, which are required for the pressure-force transformation, can be determined from geometric and motion analysis, or alternatively, from Finite Element simulations. The proposed CForce method has been implemented into… More >

M.A.Arafin¹, J.A.Szpunar²

CMC-Computers, Materials & Continua, Vol.14, No.2, pp. 125-140, 2009, DOI:10.3970/cmc.2009.014.125

Abstract A novel microstructure, texture and grain boundary character based model has been proposed to simulate the intergranular crack propagation behavior in textured polycrystalline materials. The model utilizes the Voronoi algorithm and Monte Carlo simulations to construct the microstructure with desired grain shape factor, takes the texture description of the materials to assign the orientations of the grains, evaluates the grain boundary character based on the misorientation angle - axis calculated from the orientations of the neighboring grains, and takes into account the inclination of grain boundaries with respect to the external stress direction. Markov Chain theory has been applied to… More >

Dyi-Cheng¹, Syuan-Yi Syong¹

CMC-Computers, Materials & Continua, Vol.13, No.3, pp. 191-200, 2009, DOI:10.3970/cmc.2009.013.191

Abstract Finite element simulations are performed to investigate the plastic deformation behavior of Ti-6Al-4V titanium alloy during its indirect extrusion through a four-hole die. The simulations assume the die, mandrel and container to be rigid bodies and ignore the temperature change induced during the extrusion process. Under various extrusion conditions, the present numerical analysis investigates the effective stress and profile of product at the exit. The relative influences of the friction factors, the temperature of billet and the eccentricity of four-hole displacement are systematically examined. The simulations focus specifically on the effects of the friction factor, billet temperature and eccentricity ratio… More >

D. S. Liu¹, C. Y. Tsai¹, S. R. Lyu²

CMC-Computers, Materials & Continua, Vol.11, No.2, pp. 147-164, 2009, DOI:10.3970/cmc.2009.011.147

Abstract This study presents a novel numerical method for extracting the tempe -rature-dependent mechanical properties of the gold and aluminum thin-films. In the proposed approach, molecular dynamics (MD) simulations are performed to establish the load-displacement response of the thin substrate nanoindented at temperatures ranging from 300-900 K. A simple but effective procedure involving genetic algorithm (GA) and finite element method (FEM) is implemented to extract the material constants of the gold and aluminum substrates. The material constants are then used to construct the corresponding stress-strain curve, from which the elastic modulus, yield stress and the tangent modulus of the thin film… More >