Wei-Ming Lee¹, Jeng-Tzong Chen^2,3

CMES-Computer Modeling in Engineering & Sciences, Vol.37, No.3, pp. 243-273, 2008, DOI:10.3970/cmes.2008.037.243

Abstract In this paper, a semi-analytical approach is proposed to solve the scattering problem of flexural waves and to determine dynamic moment concentration factors (DMCFs) in an infinite thin plate with multiple circular holes. The null-field integral formulation is employed in conjunction with degenerate kernels, tensor transformation and Fourier series. In the proposed direct formulation, all dynamic kernels of plate are expanded into degenerate forms and further the rotated degenerate kernels have been derived for the general exterior problem. By uniformly collocating points on the real boundary, a linear algebraic system is constructed. The results of dynamic moment concentration factors for… More >

R. Valisetty^1,2, A. Rajendran^1,3, D. Grove²

CMES-Computer Modeling in Engineering & Sciences, Vol.60, No.1, pp. 41-72, 2010, DOI:10.3970/cmes.2010.060.041

Abstract A multi-scale model exhibiting progressive damage is considered for a 3D-woven composite. It is based on the evolution of some fundamental damage modes in a representative volume element (RVE) of a composite's woven architecture. The overall response of a woven composite due to a variety of damage modes is computationally obtained through a transformation field analysis (TFA) that is capable of quantifying the effects of spatial distribution of micro stresses and strains on strength. Since the model is computationally intensive, its numerical requirements are to be understood before it can successfully be used in design studies or in conjunction with… More >

Xuebo Zhang^{1, 2, 3}, Zhiwei Jia^{1, 2, 3, *}

FDMP-Fluid Dynamics & Materials Processing, Vol.15, No.1, pp. 53-61, 2019, DOI:10.32604/fdmp.2019.04779

Abstract The influence of ground stress was quantitatively analyzed on coal seam gas pressure and gas content in this paper. Mining activities in coal mine can result in stress concentration in the coal (rock) body around the mining space, but porosity of the coal seam would not change too much. Therefore, gas pressure and gas content in the coal seam are slightly affected. Studies showed that the free gas was gradually transformed into adsorbed gas, and the gas adsorption volume was small, and then gas pressure increases roughly linearly when the porosity decreased because of stress influence. Additionaly, when porosity of… More >

Hameed Muhamad¹, Simant Upreti ², Ali Lohi³, Huu Doan⁴

FDMP-Fluid Dynamics & Materials Processing, Vol.12, No.3, pp. 111-123, 2016, DOI:10.3970/fdmp.2016.012.111

Abstract Heavy Oil is an up and coming energy resource that is aggressively being sought after as the world’s energy demand increases. As technology continues to improve, this once costly energy source is quickly becoming a more viable alternative. Vapor extraction (Vapex) process is an emerging technology for viscous oil recovery that has gained much attention in the oil industry. The vapor extraction of heavy oil system is presented to describe experimental setups and procedures used to perform different experiments of vape extraction process. The generated experimental data were used to calculate the live oil maximum interfacial solvent concentration as function… More >

K. Sefiane¹

FDMP-Fluid Dynamics & Materials Processing, Vol.1, No.3, pp. 267-276, 2005, DOI:10.3970/fdmp.2005.001.267

Abstract In this paper the experimental results on the wetting behaviour of volatile binary sessile drops are reported. The evaporation rate is varied through the control of the ambient total pressure. The dynamic wetting contact angle of an evaporating Water-Ethanol drop is investigated at various sub-atmospheric pressures. The wetting properties (contact angle, shape and volume) are monitored in time using a drop shape analysis instrument. The results show that the evaporation of the binary droplet takes place in two stages: the first stage where the wetting behaviour is very similar to the pure ethanol case and a second stage where the… More >

Kunigal N. Shivakumar¹, Anil Bhargava², Sameer Hamoush³

CMC-Computers, Materials & Continua, Vol.6, No.2, pp. 71-92, 2007, DOI:10.3970/cmc.2007.006.071

Abstract A detailed and accurate three-dimensional finite element stress analysis was conducted on countersunk rivet holes in a plate subjected to tension loading. The analysis included a wide range of countersunk depths, plate thicknesses, countersunk angles and plate widths. The study confirmed some of the previous results, addressed their differences, provided many new results, and investigated countersunk angle and width effects. Using the detailed FE results and the limiting conditions, a general equation for stress concentration was developed and verified. More >

A. Bakkali¹, L. Azrar^1,2, N. Fakri¹

CMC-Computers, Materials & Continua, Vol.23, No.3, pp. 201-232, 2011, DOI:10.3970/cmc.2011.023.201

Abstract In this paper an N-phase Incremental Self Consistent model is developed for magnetoelectroelastic composites as well as the N-phase Mori-Tanaka and classical Self Consistent. Our aim here is to circumvent the limitation of the Self Consistent predictions for some coupling effective properties at certain inclusion volume fractions. The anomalies of the SC estimates are more drastic when the void inclusions are considered. The mathematical modeling is based on the heterogeneous inclusion problem of Eshelby which leads to an expression for the strain-electric-magnetic field related by integral equations. The effective N-phase magnetoelectroelastic moduli are expressed as a function of magnetoelectroelastic concentration… More >

Xue-Qian Fang^1,2, Xiao-Hua Wang¹, Le-Le Zhang³

CMC-Computers, Materials & Continua, Vol.16, No.3, pp. 229-246, 2010, DOI:10.3970/cmc.2010.016.229

Abstract In the design of advanced micro- and nanosized materials and devices containing inclusions, the effects of surfaces/interfaces on the stress concentration become prominent. In this paper, based on the surface/interface elasticity theory, a two-dimensional problem of an elliptical nano-inhomogeneity under anti-plane shear waves is considered. The conformal mapping method is then applied to solve the formulated boundary value problem. The analytical solutions of displacement fields are expressed by employing wave function expansion method, the expanded mode coefficients are determined by satisfying the boundary conditions at the interfaces of the nano-inhomogeneity. Analyses show that the effect of the interfacial properties on… More >

Kunigal N. Shivakumar¹, Anil Bhargava¹, Sameer Hamoush²

CMC-Computers, Materials & Continua, Vol.3, No.2, pp. 97-106, 2006, DOI:10.3970/cmc.2006.003.097

Abstract A detailed three-dimensional finite element stress analysis was conducted on straight-shank and countersunk rivet holes in a plate subjected to tension loading. The study included a wide range of plate width to radius, thickness to radius, countersunk depth to thickness ratios and countersunk angles(θ_c). The stress concentration is maximum at or near the countersunk edge. The stress concentration depends on countersunk depth, plate thickness and width and it is nearly independent of the countersunk angle for 80° ≤ θ_c ≤ 120°. Using the finite element results and limiting conditions, an equation for stress concentration factor is developed and verified. More >